Ballard Designs Large Eastman Secretary MO386 User manual

PRODUCT NAME: Large Eastman Secretary*
ITEM NUMBER: MO386
ASSEMBLED DIMENSIONS: 47”H x 48”W X 19 1/2”D
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 1-12-2021 Page 1 of 5
IMPORTED
* Installed Power Strip is NOT a surge supressor/protector.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 5
Ltr.
C2
Legal Size File Bars
Shelves (F)
D4Wood Plugs
A 16
Shelf Supports
B2Letter Size File Bars
Qty. Hardware Included
Ltr.
F 4
Qty. Components
E2
REQUIRED TOOLS:
Phillips and Flat Head Screwdrivers
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
Assemble in location for intended use.
Wall Anchoring
(Anti-tip) Hardware
See page 5
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
ANCHORING HARDWARE INCLUDED
Cleaning and Care
Periodically dust with a soft, dry cloth.
Prevent finish damage: do not use alchohol based
cleaners or polishers. Promptly remove spills.
G1
Secretary (G)

(C)
(B)
Page 3 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(D)
Assemble in location for intended use.
STEP 1: Open lower drawer and insert either Letter Size (B) or Legal Size (C) File Bars into notches
along inside top edge. NOTE: Orient LETTER along drawer length. LEGAL along drawer depth.
STEP 2: Secretary is equipped with Rotary Levelers under each corner which are accessed from INSIDE
cabinet. Insert Flat Head Screwdriver into hole to engage with Slot in leveler. Turn clockwise/counter-
clockwise to adjust. NOTE: Uneven doors may be rectified by adjusting Levelers.
When complete, cover open holes with Wood Plugs (D).

(A)
(F)
Page 4 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Assemble in location for intended use.
STEP 3: Determine location for each Shelf (F) then insert Shelf Supports (A) into applicable pre-drilled
holes along wall of each compartment. Carefully place each Shelf level upon supports.
NOTE: Right compartment is designed with an opening for use with a CPU. If using compartment
for housing a CPU, do not install Shelf or Shelf Supports.
CPU COMPARTMENT: To place CPU in Secretary, slide open rear door and slide CPU in from back. TO
ALLOW FOR CPU HEAT DISSIPATION permit unit to slightly hang out of back of compartment. This will
also provide space for the front door to completely close.
Connect all cables and cords BEFORE attaching Wall Anchoring Hardware.
Installed Power Strip is NOT a Surge Supressor/Protector.

Page 5 of 5
Installation:
Ltr.
A2
Small Screw
Retention Belt
Qty. Hardware Included
B2
Large Screw
C4 Bracket
D2
WALL ANCHORING HARDWARE (ANTI-TIP)
1. Place furniture against wall at desired location then locate and mark a Wall Stud behind unit.
2. Corresponding to Stud location, attach one Bracket (C) to back of unit using Small Screw (B).
3. To keep hardware out of view after installation, attach remaining Bracket (C) INTO WALL STUD
with Large Screw (A) 2 inches below Bracket attached to back of unit.
4. Move unit into place, align Brackets then connect both using Retention Belt (D).
5. Confirm Belt is securely laced and locked.
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
W
A
L
L
S
TUD
WALL BRACKET MUST BE ATTACHED TO WALL STUD
(A)
(B)
(C)
(D)
R
e
presen
t
a
tiv
e
Fu
r
nitu
r
e
I
tem
Cleaning and Care
Avoid harsh or abrasive chemicals as finish damage may result.
Use coasters, trivets, place mats to protect surfaces. Promply remove spills.
Dust with a soft, dry cloth.