Ballard Designs Lauren Wall Desk WS987 User manual

PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 3-31-2020 Page 1 of 6
PRODUCT NAME: Lauren Wall Desk
ITEM NUMBER: WS987
ASSEMBLED DIMENSIONS : 17 1/2”H x 30”W x 9 1/8”D
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN CHINA

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 6
Ltr.
A4
B 2
Qty. Hardware Included
Ltr.
E
F
1
1
Qty. Components
C 2
REQUIRED TOOLS:
Phillips Screwdriver, Level,
Pencil, Drill. 1/4” and 3/8” bit
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
NOTE: To avoid accidentally
discarding small parts or hardware,
retain all carton contents until
assembly and installation are complete.
Screws
Expansion Bolts
Wall Anchors
Wood Plugs
D2
HARDWARE
Wall Decor is HEAVY and requires adequate support.
Falling Hazard
Wall Brackets must be firmly attached to WALL STUDS.
WARNING
Desk (E)
Wall Bracket (F)
Assemble in location for intended use.

Page 3 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 1: Determine installation site and locate at least two WALL STUDS in wall behind Desk. Use a
level to position Wall Bracket (F) and center a hole over each WALL STUD. Insert and drive Screw (A)
directly into WALL STUD. For holes located in open drywall (no stud) use an Expansion Bolt (B).
See Step 2 for installation instructions.
WALL BRACKET MUST BE ATTACHED TO WALL STUD
(F)
(B)
(A)
STEP 2: For Bracket hole locations where no wall stud is present, mark location and use a drill with a
3/8” bit to create a pilot hole. Lightly tap Expansion Bolt (B) into hole and sink teeth into wall surface.
Drywall
3/8” Drill Bit
(B)
Teeth

Page 4 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 3: Use a screwdriver to press down and firmly turn screw clockwise until it begins to slip indicating
the barrel has crimped against inside of drywall. Back out and completely remove Screw, leaving
bolt/anchor in wall. Position Bracket (F), align holes, replace and tighten Screw.
Barrel
Turn screw until it slips Remove screw
STEP 4: With Bracket (F) firmly attached to wall, carefully lift Desk (E) and engage cleat on back with
Bracket as illustrated below. Gently push/pull down until Desk is fully seated and locked in place.
B
a
c
k
ofD
e
s
k
(F)
(E)

Page 5 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(E)
STEP 5: Carefully open and fold down door and use a pencil to mark location for both screw holes on
the inside bottom edge of Desk (E).
STEP 6: Carefully lift and remove Desk (E) from wall. Use a drill with a 1/4” bit to create a pilot hole
at each mark then gently tap Wall Anchors (C) into place until flush with wall surface.
(C)

Page 6 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(D)
(E)
(A)
STEP 7: Return Desk (E) to wall and lock onto Bracket. Align both interior holes with Wall Anchors,
insert Screw (A), fully tighten, then cover hole with Wood Plug (D).
Cleaning & Care:
DO NOT use alcohol based products or spray polisher as they can damage the finish.
Dust with soft cloth. Finish can be affected by heat or extended contact with oils or wine.