Ballard Designs Tuscan Secretary Desk User manual

PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 6/17/2019 Page 1 of 7
PRODUCT NAME: Tuscan Secretary Desk
ITEM NUMBER: MO400
ASSEMBLED DIMENSIONS : 81 3/4”H x 36”W x 15”D
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
IMPORTED

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 7
Ltr.
A 8
B 2
Qty. Hardware Included
Ltr.
E
F
1
1
Qty. Components
C 16
D 2
Hardware Packet and
Shelves (E & F) Here
Shelf Bracket
File Rod
Screw
L-Bracket
(Anti-tip Hardware)
Serious or fatal crushing injuries can occur from a furniture tip-over
WARNING
Tip-Over Hazard
WALL BRACKET MUST BE ATTACHED TO WALL STUD
Prevent tipping accidents. Anchor your furniture.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
NOTE: To avoid accidentally
discarding small parts or hardware,
retain all carton contents until
assembly and installation are complete.
REQUIRED TOOLS:
-Phillips Screwdriver
-Pencil
-Power Drill (optional)
Requires at least two people for
installation.
IMPORTANT: Power Strip included with Secretary Desk is not a surge protection device.
Glass Shelf
Desk Shelf

Page 3 of 7
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
NOTE: Assemble in intended area for use.
STEP 1: Open lower drawer and install File Rods (B) into notches in drawer edge.
NOTE: To prevent an accidental tip-over, a locking mechanism has been installed on the lower two
drawers which prevents both to be open at the same time. One drawer must be closed in order to
open the other.
(B)
STEP 2: Install Glass Shelf (E) into upper compartment by inserting four Shelf Supports (A) at
desired height and gently laying shelf in place upon supports.
Add remaining four supports to drop-down desk compartment and gently lay in Desk Shelf (F).
NOTE: The optional power strip may be removed by taking out screws and gently pulling cord
out through front of Cabinet. Power Strip is NOT a surge protection device.
(E)
(F)

Page 4 of 7
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
NOTE: Assemble in intended area for use.
LEVELERS: If doors are uneven, adjust Levelers on bottom of each corner by turning clockwise or
counter-clockwise until doors are evenly aligned.
Easy Touch
Touch metal
hinge for 3-level
light control
LIGHTED CABINET: Plug electrical cord into an outlet. Cabinet is equipped with an “Easy Touch”
dimmer control which allows for three levels of brightness. To operate, touch upper right hinge.

Serious or fatal crushing injuries can occur from a furniture tip-over
WARNING
Tip-Over Hazard
WALL BRACKET MUST BE ATTACHED TO WALL STUD
Prevent tipping accidents. Anchor your furniture.
Page 5 of 7
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
NOTE: Assemble in intended area for use.
ANTI-TIP INSTALLATION STEP 1: Locate Wall Studs then center Secretary in front and mark
their location on wall. Push Secretary fully against the wall.
Wall
Studs
Wall Stud
(D)
ANTI-TIP INSTALLATION STEP 2: Slide L-Brackets (D) over back top corner of Secretary in front
of previously marked Studs. Mark the wall at the top of each Bracket. NOTE: Position brackets
as shown to ensure they are NOT VISIBLE once installation is complete.

Page 6 of 7
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Cleaning & Care:
DO NOT use alcohol based products or spray polisher as finish damage may result.
Dust with a soft cloth.
NOTE: Assemble in intended area for use.
(D)
Wall
(C)
ANTI-TIP INSTALLATION STEP 3: Pull Secretary away from wall then position and attach both
L-Brackets (D) to the Wall Studs using Screws (C).
ANTI-TIP INSTALLATION STEP 4: Slide Secretary back to wall and re-center under each
installed L-Bracket (D). Use two or more of the remaining Screws (C) to securely attach
Secretary to Brackets. NOTE: Due to floor molding, Secretary may not completely push back to
wall and Bracket may not fully cover. Use screws on only those holes that cover top of Secretary.
(D)
(C)
Wall

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 7 of 7
HALOGEN BULB REPLACEMENT:
Insert the new Bulb (A) into the Fixture Body (C) Socket using a tissue or soft cloth (oil from the
skin my damage the bulb). Replace the Lens Cover (B) by twisting it clockwise back into place.
1
Qty.
Halogen JCD G8 120V 25W
Replacement Bulb (A)
NOT INCLUDED
Item needed
Unplug the unit from the wall. Remove the Lens Cover (B) from the Fixture Body (C) by turning it
counter clockwise and pulling it away from the unit. Remove the old Bulb (A) by pulling it straight
out in a horizontal direction.
(B)
(C)
(B)
(C)
(A)
NOTE: Save this page for future bulb replacement.