Ballard Designs Dover Shiplap MS106 User manual

PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 4-30-2020 Page 1 of 5
PRODUCT NAME: Dover Shiplap Console
ITEM NUMBER: MS106
ASSEMBLED DIMENSIONS : 38”H x 73 3/4”W x 15 1/2”D
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN CHINA

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 5
Ltr.
D
E
2
4
Qty. Components
C 1
REQUIRED TOOLS:
-Phillips Screwdriver
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
NOTE: To avoid accidentally
discarding small parts or hardware,
retain all carton contents until
assembly and installation are complete.
Assemble in location for intended use.
Shelves (D)
Console (C)
B2
Included HardwareLtr. Qty.
A 8 Shelf Supports
Wall Anchoring
(Anti-tip) Kits
See Page 5
WARNING
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
ANCHORING HARDWARE INCLUDED
F
E
1Middle Leg (F)
Doors (E)
Shelves (D)
Hardware Packet
Doors (E)
Middle Leg (F)

STEP 1: NOTE: To protect finish, consider leaving packaging in place for this step. Invert Console (C)
onto a clean, level surface then insert, turn and hand-tighten Middle Leg (F) into embedded T-nut in
center base of Console.
(C)
(F)
Page 3 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Assemble in location for intended use.
STEP 2: Set Console (C) upright, remove all packaging and determine location for each Shelf (D).
Insert Shelf Supports (A) into corresponding pre-drilled holes then set each Shelf level upon Supports.
(A)
(C)
(D)

Page 4 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Cleaning & Care:
DO NOT use alcohol based products or spray polisher as
they can damage the finish. Dust with soft cloth.
Assemble in location for intended use.
STEP 3: Align and place wheels on bottom of two Doors (E) into REAR TRACK in base of
Console (C) then gently push top of each Door into Console. NOTE: Be certain track guides on the
top of each door are pushed in and locked before pushing door in. Once top of Door is aligned with
top rear track, push button on guide assembly and guide will pop up and into track.
Repeat process for both doors in FRONT TRACK.
U
p
p
e
r
T
r
a
c
k
L
o
w
e
r
T
r
a
c
k
W
h
e
e
l
Po
p
-o
u
t
T
r
ack
G
ui
d
e
(C)
(E)
STEP 4: Console is equipped with Rotary Levelers located under each corner. If necessary, adjustments
may be made by carefully lifitng corner then turning Leveler clockwise/counterclockwise.

Page 5 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Installation:
Ltr.
A2
Small Screw
Retention Belt
Qty. Hardware Included
B2
Large Screw
C4 Bracket
D2
WALL ANCHORING HARDWARE (ANTI-TIP)
1. Place furniture against wall at desired location then locate and mark a Wall Stud behind unit.
2. Corresponding to Stud location, attach one Bracket (C) to back of unit using Small Screw (B).
3. To keep hardware out of view after installation, attach remaining Bracket (C) INTO WALL STUD
with Large Screw (A) 2 inches below Bracket attached to back of unit.
4. Move unit into place, align Brackets then connect both using Retention Belt (D).
5. Confirm Belt is securely laced and locked.
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
W
A
L
L
S
TUD
WALL BRACKET MUST BE ATTACHED TO WALL STUD
(A)
(B)
(C)
(D)
R
e
presen
t
a
tiv
e
Fu
r
nitu
r
e
I
tem