Ballard Designs Del Ray Ping Pong Table JM083 User manual

PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 3-2-2020 Page 1 of 8
PRODUCT NAME: Del Ray Ping Pong Table
ITEM NUMBER: JM083
ASSEMBLED DIMENSIONS : 30”H x 48”W x 96”L
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN USA

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 8
20 Key
Allen Screw
Allen Wrench
Long Crossbar
20
Qty. Hardware Included
2
Net1
Top Crossbar Middle
2
Top Crossbar End
2
Shelf
2
Bottom Crossbar
2
Table Leg2 Table Top1
Ping Pong Paddles2 Ping Pong Balls4
Qty. Components
Bracket2
Qty. Components
1
TOOLS NEEDED:
Rubber Mallet. Two person assembly suggested.
Remove all parts, hardware and protective
packaging from carton and carefully arrange
on a clean, level, padded surface.
NOTE:
To avoid accidentally discarding small parts
or hardware, retain all carton contents until
assembly and installation are complete.

Page 3 of 8
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 1: Locate the 2 table legs and 8 keys. Insert the keys into the key slots on the inside
of the table legs. Wait until step 10 to screw the keys into place.
Align the corresponding slots of the bottom crossbars and the table legs with the letter
system facing the inside of the table. Slide the pieces together, using a mallet if needed,
and continue until all 4 pieces are assembled together.
STEP 2:
IMPORTANT:
1. Unpack and lay all Ping Pong Table pieces flat on a padded surface to avoid scratching
or damaging the components.
2. Look for an engraved letter near each slot on the enclosed pieces. Always match
up coordinating slots (A+A, B+B, etc.) to ensure proper assembly.
3. Locate all hardware before discarding any packaging.
A
F
E
L
K
J
I
B
C
I
JK
L
F
E

Page 4 of 8
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 3: Locate the 2 shelves and place them on top of the bottom crossbars. Once in place,
maneuver the shelves slightly until they are positioned correctly over the fasteners and
use a slight tap on each corner to secure.
Align the corresponding letters of the 2 brackets and insert them into the table legs
using the letter system. Slide the pieces together, using a mallet if needed.
STEP 4:
F
F
E
G
K
L
J
I
A
F
E
L
K
J
I

Page 5 of 8
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 5: Insert 4 additional keys into the key slots located on the brackets as you did in step 1.
Wait until step 10 to screw the keys into place.
Align the corresponding letters of the top crossbars and insert them into the table legs
using the letter system. Slide the pieces together, using a mallet if needed, and continue
until you have inserted all 4 crossbars (2 middle crossbars, 2 end crossbars) into the table
legs and the tops are flush.
STEP 6:
FF
K
K
I
L
M
R
N
I
JK
L
FF

Page 6 of 8
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 7: Insert 8 remaining keys into the key slots located on the brackets as you did in step 1.
Wait until step 10 to screw the keys into place.
Align the corresponding letters of the long crossbar and insert the piece into the table
frame using the letter system. Slide the pieces together, using a mallet if needed,
and continue until the top of the long crossbar is flush with the rest of the frame.
STEP 8:
K
L
L
M
R
N
K
K
K
K
K
L
L
M
Q
R
R

Page 7 of 8
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 9: Place the table top on top of the frame. Adjust slightly until the grooves on the bottom
of the table align and the table rests properly on the table frame.
Locate the 20 keys you have already inserted into the table and screw them into place
using the included Allen screws and Allen wrench.
STEP 10:
M
R
R
FF
B
A
L
L

Page 8 of 8
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 11: Snap the net into place, using a mallet if necessary.
CLEANING INSTRUCTIONS:
ROUTINE CLEANING
For routine cleaning, just use water and a soft cloth or microfiber towel, or spray down
with a water hose. For a deeper clean, use mild soap and water and a soft bristle brush.
POWER WASHING
If power washing is desired, start with a low PSI, at least 3 ft away from furniture.
Move closer or increase PSI gradually and with caution. While power washing,
check often to ensure no inscription is left on the furniture.