Ballard Designs Louis XVI Poster Bed MB372 User manual

PRODUCT NAME: Louis XVI Poster Bed
ITEM NUMBER: MB372
DIMENSIONS OF ITEM ASSEMBLED:
92”H x 66“/83”W x 85”D
This item is not intended for commercial use.
Made in Italy.
Page 1 of 5
2010 Ballard Designs, Inc.
Check to ensure that you have the following:
Hardware Included
.ytQ.rtL
A 8
B 4
Part List
.ytQ.rtL
D
E
G
F
1
1
4
2
Headboard
Footboard
Wood Support Rails
Side Rails
H
J
I
3
4
4
Plastic Feet
Feet
Finials
C 1
Large Screws
Pre-installed Bolts
Tool
800.367.2810
www.ballarddesigns.com
For Assembly Purposes:
-Requires 2 people.
-Requires a screwdriver.
K 4 Poster Poles (2 Sm. / 2 Lg.)
Poster Rails (2 Sm. / 2 Lg.)
L 4

800.367.2810
www.ballarddesigns.com
STEP 1: Feet Assembly
STEP 2: Side Rail Installation
Page 2 of 5
2010 Ballard Designs, Inc.
Twist in the Feet (J) to the Headboard (D) and Footboard (E).
Release the Pre-installed Bolt (B) out of the Side Rail (F) using the Tool (C) provided. Then, with
your hand, screw in the shorter side of the Bolt (B) into the center slot of the Headboard (D).
Slide the Side Rail (F) into the Headboard with the cam lock and Wood Support Rails (G) holders
facing inward. Tighten the cam lock with the Tool (C) and repeat this process on all 4 corners.
(J) (J)
Smaller Side, screwed
into Headboard
(F)
(F)
(E)
(D)
(D)
(D)
(C)
(C)
(B)
(B)

Page 3 of 5
2010 Ballard Designs, Inc.
800.367.2810
www.ballarddesigns.com
STEP 3:Plastic Feet Installation
Install Plastic Feet (H) into the 3 Wood Rails (G) that have the additional wood block
added to them. The 3 rails with the additional wood blocks have receiving holes
for the Plastic Feet (H).
(H)
(G)
STEP 4: Wood Support Rails Installation
Place Wood Support Rails (G) in bed frame in the U-shaped supports on the Side Rails (F) with the
Plastic Feet facing the floor. Using the Large Screws (A), install the 4 Wood Support Rails (G).
Be sure to put the support rail with no Plastic Foot closest to the Footboard (E).
(G)
(F)
(A)

Twist in the Poster Poles (K). Attach the long poster poles to the Footboard (E) and
the short poster poles to the Headboard (D).
STEP 5:Poster Pole Assembly
Page 4 of 5
2010 Ballard Designs, Inc.
800.367.2810
www.ballarddesigns.com
(E)
(D)
(K)
1) Place the 2 shorter Poster Rails (L) above the Headboard (D) and the Footboard (E).
2) Place the Longer Poster Rails (L) perpendicular to the first 2.
STEP 6:Poster Rail Assembly
1) 2)

(I)
(I)
Cleaning & Care:
DO NOT use alcohol based products or spray polisher as they can damage the finish.
Dust with soft cloth. One to two times monthly apply beeswax polish as needed.
Finish can be affected by heat or extended contact with oils or wine.
Page 5 of 5
2010 Ballard Designs, Inc.
800.367.2810
www.ballarddesigns.com
Twist in the Finials (I) to all four corners.
STEP 7:Finial Assembly