Bradley HSR20 User manual

215-1678 Rev. A; EN 10-03-006
© 2010 Bradley Corporation
Page 1 of 3 4/13/10
P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX [phone]
bradleycorp.com
Installation
IMPORTANT!
Read this entire installation manual to ensure proper installation. When
finished with the installation, file this manual with the owner or maintenance
department. Compliance and conformity to local codes and ordinances is
the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for
before discarding packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Make sure that all water supply lines have been flushed and then completely
turned off before beginning installation. Debris in supply lines can cause
valves to malfunction.
Product warranties may be found under “Products” on our web site at
bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
•
•
•
•
Anti-Ligature Shower
HSR20
Supplies Required ................................................. 2
Rough-in Dimensions ............................................ 2
Installation ............................................................. 3
Caring for Stainless Steel...................................... 3
Bradley Corporation assumes no liability for
self-inflicted harm when using this product.
DISCONTINUED

HSR20 Installation
24/13/10 Bradley Corporation • 215-1678 Rev. A; EN 10-03-006
Recommended Shower Heights
Age Male Female
Adult 6'0" (1.83m) 6'0" (1.83m)
Teenage 6'0" (1.83m) 5'6" (1.68m)
Pre-Teens 5'6" (1.68m) 5'6" (1.68m)
Supplies Required
• Water supply piping to connect 1/2" NPT flexible
hose(s)
• Suitable wall anchors and 1/4" diameter fasteners
to mount shower to the wall
• Pipe Sealant
Shower Dimensions
Supplies thru-wall
Supplies from above
1Rough-In Supply
Supply inlets are 1/2" NPT flexible hose and are accessible from the back of the shower or from knockouts on the top cover.
Bradley’s HD valve shown; other valve versions install in similar manner.
• If supplies will be run “thru-wall”, Bradley recommends using a 90° street ell to connect the supply hoses.
• If supplies will be run “from above”, Bradley recommends running them approximately 1/2" into the top cover.
4"
(102)
4"
(102)
5"
(127)
(mm)
4"
(102)
7-1/2"
(190)
33-1/2"
(851)
34-1/4"
(870)
14"
(355)
Hot
Supply Cold
Supply
6-3/4"
(171)
6-1/4"
(159)
7-1/4"
(182)
8"
(204)
DISCONTINUED

Installation HSR20
Bradley Corporation • 215-1678 Rev. A; EN 10-03-006 4/13/10 3
2Install Shower
Cleaning Stainless Steel
Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive. Proper care, particularly
under corrosive conditions, is essential. Always start with the simplest solution and work your way toward the more complicated.
Routine cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia. Apply the cleaning
solution per the manufactures instructions and always use a soft cloth or sponge to avoid damaging the finish.
Stubborn Stains: To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball® stainless steel
cleaner or a soft abrasive. Always follow the manufactures instructions and apply in the same direction as the polish lines.
Special Situations for Material
Fingerprints and Smears: To remove fingerprints or smears use a high quality stainless steel cleaner and polish in accordance with
the manufactures instructions. Many of these products leave a protective coating the helps prevent future smears and fingerprints.
Grease and Oil: To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in accordance to the
manufactures instructions and in the direction of the polish lines.
Precautions: Avoid prolonged contact with chlorides (bleaches, salts), bromides (sanitizing agents), thiocyanates (pesticides,
photography chemicals, and some foods), and iodides on stainless steel equipment, especially if acid conditions exist.
The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for the actual source of
the rust in some iron or steel particles which may be touching, but not actually a part of the stainless steel structure.
Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement, nor
does the omission of any brand name cleaner imply its inadequacy. Many products named are regional in distribution, and can be
found in local supermarkets, department and hardware stores, or through your cleaning service. It is emphasized that all products
should be used in strict accordance with package instructions.
Never use ordinary steel wool or steel brushes on stainless steel.
Always use stainless steel wool or stainless steel brushes.
Do not permit salty solutions to dry and evaporate on stainless steel.
Strongly acidic or caustic cleaners may attack the steel causing a
reddish film to appear. The use of these cleaners should be avoided.
APosition unit at desired height and
using the mounting tabs as a template,
mark wall. Drill holes for 1/4" fasteners
(supplied by installer.) BConnect the 1/2" flexible hoses to the
supply lines. Turn the water on and
check for leaks and adequate water
supply. Mount unit securely on wall.
DISCONTINUED