Bradley Verge LVS Series User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
215-1828 Rev. B; ECN 16-08-008
© 2016 Bradley
Page 1 of 12 6/6/2016
LVSD1
Verge®Lavatory System – LVS-Series
with Evero®Natural Quartz Material
Table of Contents
Components ..................................................................3–4
Supplies Required .............................................................5
Dimensions....................................................................5–6
Rough-Ins ..........................................................................7
Frame Mounting.................................................................8
Faucet Box and Valve Mounting ........................................9
Overflow Plug Assembly....................................................9
Drain Assembly ...............................................................10
Faucets and Optional Soap Valve ...................................10
Bowl Mounting .................................................................11
Strainer and P-trap ..........................................................11
Adjust Temperature..........................................................12
Trap Cover .......................................................................12
Cleaning and Maintenance..............................................13

LVSD1 Installation
26/6/2016 Bradley • 215-1828 Rev. B; ECN 16-08-008
WARNING
Make sure that all water supply lines have been flushed and then completely turned off before beginning
installation. Debris in supply lines can cause valves to malfunction.
Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to installation. Electrical
power MUST remain off until installation is complete.
Installer's hardware must be appropriate for wall construction. Wall anchors must have a minimum pull-out
rating of 1,000 pounds.
IMPORTANT
Read this entire installation manual to ensure proper installation. When finished with the installation, file this
manual with the owner or maintenance department. Compliance and conformity to local codes and ordinances
is the responsibility of the installer. Product warranties may be found under “Products” on our Web site at
www.bradleycorp.com.
Separate parts from packaging and make sure all parts are accounted for before discarding any packaging
material. If any parts are missing, do not begin installation until you obtain the missing parts.
For standard height mounting, do not exceed the recommended 33.5" distance from the fixture rim to the
finished floor.

Installation LVSD1
Bradley • 215-1828 Rev. B; ECN 16-08-008 6/6/2016 3
Components
Bowl
Contact your Bradley Representative for
color options
Individual Rough-In Option
Chrome P-trap (S29-094)
Plastic P-trap (269-1697)
Complete Drain Prepack
(S45-2862)
O-Ring
(125-111)
Drain
Adapter
Packing
Washer
#10-24
Screw
Drain
Adapter
Prepack
(S45-2480)
Prepack
(S45-2861) *Screw
Strainer
*Standoff, Hex,
SS #6-32 x 1"
*Screw #6-32
x 1-1/4" Pan
*Included in
Prepack S45-2778
Access Panel
(186-1904)
Wall Bracket
(140-1153)
TMV Valve
(½" NPTM
Outlet)
(S45-2701)
Hose Prepack
(S45-2730)
Supply
Fittings
(S45-2712)
Hose Prepack
(S45-2702)
TMV Supply
Connections
Tempered Supply
Connections
Plastic Hose
Plastic
Hose

LVSD1 Installation
46/6/2016 Bradley • 215-1828 Rev. B; ECN 16-08-008
Components
IR-DCD Faucet*
(S53-336)
CAP-DCA Faucet**
(S53-334)
Battery Box for
CAP-DCA Faucets
6315-KT0000 Soap Dispenser 6324-68 Soap Dispenser 6334 Soap Dispenser
Optional
Transformer
Plug-In Transformer
Option (PT) for
IR-DCD Faucet
(S53-337)
Plug-in transformer option (PT)
includes Transformer (S53-338),
Adapter (S53-339), and Grounding
Kit (S53-349) for CAP-DCA Faucets
IR-DCG Faucet*
(S53-350)
Plug-In Transformer
Option (PT) for
IR-DCG Faucet
(153-486)
*Adapter included with faucet (TMV: S45-2872, TL: S45-2871) *Adapter included with faucet (TMV: S45-2872, TL: S45-2871)
**Adapter S45-2873 included with faucet

Installation LVSD1
Bradley • 215-1828 Rev. B; ECN 16-08-008 6/6/2016 5
Dimensions
Top View (shown with CAP-DCA faucet and 6315 soap)
Front View
Supplies Required
• (4) ³⁄₈" fasteners and wall anchors (minimum pull-out rating of 1,000 lbs.)
• (2) ¼" fasteners and wall anchors (minimum pull-out rating of 100 lbs.)
• ½" hot/cold or tempered stub-out
• 1½" NPT drain stub-out(s)
• OPTIONAL: (1) 110 volt GFCI protected electrical outlets for 100–120 VAC plug-in transformers only
• Screen filter(s) as needed, if not included with faucet(s)
• OPTIONAL: (1) ³⁄₈" NPS x ³⁄₈" NPT Male Adapter for IR-DCD faucet only
21"
(533mm)
4¼"
(165mm)
6"
(152mm)
2" (51mm)
2½"
(64mm)
19³⁄₈"
(492mm)
30"
(762mm)
12⁷⁄₈"
(327mm)
1⁷⁄₈"
(48mm)

LVSD1 Installation
66/6/2016 Bradley • 215-1828 Rev. B; ECN 16-08-008
Dimensions – Side View
A
B
14"
(356mm)
13¹⁄₈"
(333mm)
C
10¹⁄₈"
(257mm)
18½"
(470mm)
ADA/TAS Standard
Height
ADA/TAS Juvenile Height
(Children 6-12 years)
CSA Standard
Height
OBC Standard
Height
AODA-2015
Standard Height
Dim A 33½" (851mm) 31" (787mm) 33½ (851mm) 33" (838mm) 32½" (826mm)
Dim B 27" (686mm) 24" (610mm) 29⁵⁄₈" (752mm) 28¹⁵⁄₁₆" (735mm) 28¹⁵⁄₁₆" (735mm)
Dim C 20¾ (527mm) 18¼ (464mm) 21¹⁄₈" (536mm) 20¼" (514mm) 19¾" (502mm)

Installation LVSD1
Bradley • 215-1828 Rev. B; ECN 16-08-008 6/6/2016 7
Mounting for Standard, ADA and TAS height shown.
Structural Rough-Ins
Points A, B and C require sufficient backing
compliant with local building codes.
Secure bracket to wall using min.
³⁄₈" anchor bolt to the left of C/L and
min. ³⁄₈" anchor bolt to the right of
C/L. The anchor bolt to the right
of C/L must be min. 5" apart from
the anchor bolt to the left of C/L.
When mounting is complete, check
to ensure the bracket is level. See
Step 1: Bracket Mounting for more
information.
31½"
(800mm)
AA
BB
8"
(203mm)
10"
(254mm)
C
L
29½"
(749mm)
Bottom of
Bracket
CODE DESCRIPTION QTY.
A Install (1) 3/8" wall anchor with a minimum pull-out force of 1,000 lbs. per local codes at locations shown 2
B
Provide structural backing compliant with local building codes. 2
C Install wall anchor with a minimum pull-out force of 100 lbs. per local codes at locations shown 2
21½"
(546mm)
Wall Bracket
WARNING Ensure bowl is completely seated in
the wall bracket and securely fastened
to the wall at point A.
RIM HEIGHT VERTICAL HEIGHT ADJUSTMENTS FIXTURE STYLE
33½" No Adjustment Standard Height, ADA, TAS and CSA
30½" Subtract 3" Juvenile, ADA and TAS
32½" Subtract 1" AODA
33" Subtract ½" OBC
C
C
25¾"
(654mm)
33½"
(851mm)
8"
(203mm)
9½"
(241mm)
9½"
(241mm)
10"
(254mm)
10"
(254mm)

LVSD1 Installation
86/6/2016 Bradley • 215-1828 Rev. B; ECN 16-08-008
Plumbing and Electrical Rough-Ins
Mounting for Standard, ADA and TAS height shown.
CODE DESCRIPTION QTY.
A 1½" NPT Drain, Stub-out 2" from wall, individual waste option 1
H,C ½" Nominal (⁵⁄₈" O.D. Comp.) Hot/Cold supplies, Stub-out 2" from wall 1
E 110V GFI protected electrical outlet (AC faucet and soap only) 1
P Outline of soap container (if selected) 1
33½"
(851)
Rim
Height
4" - 5"
(105 - 127)
2" - 3"
(51 - 76)
7" - 8"
(178 - 203)
20¾"
(527)
23" - 24"
(584 - 610)
20" - 23"
(508 - 584)
26" - 27"
(660 - 686)
A
P
E
H C
(mm)

Installation LVSD1
Bradley • 215-1828 Rev. B; ECN 16-08-008 6/6/2016 9
Bracket Mounting
Typical installation is shown. It may be necessary to repair the wall
after mounting. The fixture may not cover all of the wall modifications.
1
5"
(127mm)
min.
Install wall bracket to wall
per structural rough-in
dimensions. Check to
ensure the bracket is
level. Example anchor
locations shown.
A
Mounting height per structural rough-in dimensions.
For ease of drain installation, lay the bowl on its back.
2Drain Assembly
Thread screw into drain
adapter until it becomes
fully engaged.
A
Thread the standoff onto
the now fully engaged
screw.
BO-Ring
Drain
Adapter
Packing
Washer
#10-24
Screw
#6-32 x 1-1/4"
Screw
Standoff, Hex
SS #6-32 x 1"
Assemble the remaining components as
shown and thread the four screws through
the drain adapter and into the basin inserts.
Ensure the screws compress the drain
adapter evenly onto the basin.
C
C
L

LVSD1 Installation
10 6/6/2016 Bradley • 215-1828 Rev. B; ECN 16-08-008
Bowl Mounting (to Bracket and Wall)
4
Strainer and P-Trap
5
Strainer
Thread the strainer screw
through the strainer and
into the stand off on the
drain adapter.
A
Position bowl above wall bracket.
Press firmly on the back of the bowl
to seat the bowl flange into the wall
bracket lip. Ensure bowl is level.
A
Secure the bowl to the wall anchors
using fasteners per the structural
rough-in requirement (supplied by
installer).
B
Ensure not to overtighten
the strainer screw.
WARNING Ensure bowl is completely seated in
the wall bracket and securely fastened
to the wall at point A.
Faucet Installation
3For ease of drain installation,
lay the bowl on its back.
Install the faucets and optional
soap valves according to the
manufacturer's instructions.
A
CAUTION Bracket is not
intended to support
the weight of bowl
for an extended
period of time. Be
sure to secure the
bowl to the wall
using appropriate
fasteners.
Install supplied p-trap to
drain adapter.
B