Bradley SXWS9148 User manual

Installation
SXWS9148
Chase-Mounted SX Panel Shower
P.O. Box 309, Menomonee Falls, WI 53052-0309
Phone: 1-800-BRADLEY Fax: [phone]
http:\\www.bradleycorp.com
215-1344 Rev. A; EN 05-715
© 2005 Bradley Corporation
Page 1 of 4 9/23/05
Table of Contents
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Cleaning Stainless Steel . . . . . . . . . . . . . . . . . . . .4
CH
WARNING
Read this entire installation manual to ensure proper installation. When finished
with the installation, file this manual with the owner or maintenance department.
Compliance and conformity to local codes and ordinances is the responsibility of
the installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Before installing components, all connection supply lines must be flushed and
free of foreign material such as pipe dope, chips, solder, etc. Bradley will not be
responsible for leaking valves due to the presence of foreign material, or
distorted stop gaskets where excessive pressure (above 30 lbs. of torque) has
been applied to the stop cap.
After flushing has been completed, make sure that all water supply lines have
been completely turned off before beginning installation. After installation has
been completed, turn the water supply lines back on and test the unit for leaks
and adequate water flow.
Product warranties may be found under "Product Information" on our web site at
www.bradleycorp.com.
THIS
SIDE
UP
Packing List




Installation

SXWS9148 Installation
2 9/23/05 Bradley Corporation • 215-1344 Rev. A; EN 05-715
72"
(1829mm)
to Finished
Floor
Recommended
44"
(1118mm)
13"
(330mm)
33-11/16"
(856mm)
to Finished
Floor
24"
(610mm)
REF.
41-3/4"
(1060mm)
43-1/2"
(1105mm)
to Finished
Floor
9"
(229mm)
WALL
OPENING
Dimensions

Installation SXWS9148
3Bradley Corporation • 215-1344 Rev. A; EN 05-715 9/23/05
Installation
Screw the threaded rods into the
coupling nuts on the back of the
shower panel. Position the shower
panel into the wall opening.
C
AInstall the control buttons
at these locations per the
instructions included with
the valve assembly.
B
Install the valve assembly and
make the valve connections to the
showerheads and control buttons
per the instructions included with
the valve assembly.
From the chase side, secure
the back plates tightly with the
washers and nuts provided.
D
LOCKWASHER
NUT
THREADED ROD
BACK PLATE

SXWS9148 Installation
4 9/23/05 Bradley Corporation • 215-1344 Rev. A; EN 05-715
Cleaning Stainless Steel
Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive.
Proper care, particularly under corrosive conditions, is essential. Always start with the simplest solution and
work your way toward the more complicated.
Routine cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or
ammonia. Apply the cleaning solution per the manufactures instructions and always use a soft cloth or
sponge to avoid damaging the finish.
Stubborn Stains: To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball®
stainless steel cleaner or a soft abrasive. Always follow the manufactures instructions and apply in the same
direction as the polish lines.
IMPORTANT: NEVER USE ORDINARY STEEL WOOL OR STEEL BRUSHES ON
STAINLESS STEEL. ALWAYS USE STAINLESS STEEL WOOL OR
STAINLESS STEEL BRUSHES.
Special Situations for Material
Fingerprints and Smears: To remove fingerprints or smears use a high quality stainless steel cleaner and
polish in accordance with the manufactures instructions. Many of these products leave a protective coating
the helps prevent future smears and fingerprints.
Grease and Oil : To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in
accordance to the manufactures instructions and in the direction of the polish lines.
Precautions: Avoid prolonged contact with chlorides (bleaches, salts), bromides (sanitizing agents),
thiocyanates (pesticides, photography chemicals, and some foods), and iodides on stainless steel equipment,
especially if acid conditions exist.
IMPORTANT: DO NOT PERMIT SALTY SOLUTIONS TO EVAPORATE AND DRY ON
STAINLESS STEEL.
The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for
the actual source of the rust in some iron or steel particles which may be touching, but not actually a part of
the stainless steel structure.
NOTE: Strongly acidic or caustic cleaners may attack the steel causing a reddish film to appear. The use of
these cleaners should be avoided.
Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an
endorsement, nor does the omission of any brand name cleaner imply its inadequacy. Many products named
are regional in distribution, and can be found in local supermarkets, department and hardware stores, or
through your cleaning service. It is emphasized that all products should be used in strict accordance with
package instructions.