Bradley Express SS Series User manual

P.O. Box 309, Menomonee Falls, WI 53052-0309
Phone: 1-800-BRADLEY Fax: [phone]
www.bradleycorp.com
Installation
215-1497 Rev. F; ECN 07-814
© 2007 Bradley Corporation
Page 1 of 14 12/11/07
SS-2N/IR/STD
SS-2N/IR/WH
Express® Lavatory System SS-Series
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . . . .2
Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Supplies Required . . . . . . . . . . . . . . . . . . . . . . . .4
Dimensions............................... 4–5
Rough-Ins ...................................6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .7–10
Solenoid Valve Troubleshooting . . . . . . . . . . . . .11
Vernatherm Mixing Valve Troubleshooting . . . . .12
Stop/Check Valve Troubleshooting. . . . . . . . . . .13
Cleaning and Maintenance for Terreon® . . . . . .13
Soap Dispenser Maintenance . . . . . . . . . . . . . .14
Express Lavatory Systems are ADA and TAS compliant
U.S. Pat. Nos. 5,611,093, D447,224
Other Patents Pending
SS-2N/IR/STD/LSD-2
SS-2N/IR/WH/LSD-2
A
D
A
•
C
O
M
P
L
I
A
N
T

SS-2N/IR/STD, SS-2N/IR/WH Installation
212/11/07 Bradley Corporation • 215-1497 Rev. F; ECN 07-814
IMPORTANT!
Read this entire installation manual to ensure proper installation. When finished with the
installation, file this manual with the owner or maintenance department. Compliance and
conformity to local codes and ordinances is the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before discarding
any packaging material. If any parts are missing, do not begin installation until you obtain the
missing parts.
Make sure that all water supply lines have been flushed and then completely turned off
before beginning installation. Debris in supply lines can cause valves to malfunction.
Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to
installation. Electrical power MUST remain off until unit and optional water heater have
been plumbed. After installation is complete, turn on the water supply first, then turn on the
electrical power.
Hardware supplied by installer must be appropriate for wall construction. Wall anchors must
have a minimum pull-out rating of 1,000 lbs. Follow appropriate dimensions for standard or
juvenile height based on configuration and required rim height. Overtightening fasteners can
damage the Terreon®material. Use caution when tightening bowl and sprayhead fasteners.
Product warranties may be found in the “Products” section on our Web site at www.
bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
•
•
•
•

Installation SS-2N/IR/STD, SS-2N/IR/WH
Bradley Corporation • 215-1497 Rev. F; ECN 07-814 12/11/07 3
P-TRAP (POLYPROPYLENE)
(269-1697)
OPTIONAL P-TRAP
(CHROME-PLATED BRASS)
(S29-094)
#8-32 SCREW
(160-319)
STRAINER
(P16-075)
DRAIN PLUG
(P16-072)
1/8" RUBBER
WASHER
(125-001DP)
TAILPIECE
(129-056)
DRAIN
ASSEMBLY
BOLT 5/16-18
160-371
SCREW 10-24
160-386
WASHER
142-002BJ
LOCKWASHER
142-002BK
NUT 5/16-18
161-036
SCUFF BASE PANEL
GRAY (185-034)
PUTTY (185-034A)
COAL (185-034B)
SCUFF PANEL FASTENERS (160-450)
WASHERS (142-002CA)
(4) PLACES
SCUFF FRAME S17-326
USED WITH STANDARD
HEIGHT FRAME ONLY
MAIN FRAME
S17-325
PANEL
FASTENERS
(160-450)
WASHERS
(142-002CA)
(6) PLACES
ACCESS PANEL
GRAY (186-1455)
PUTTY (186-1455A)
COAL (186-1455B)
SPRAYHEAD COVER
(PART NUMBER VARIES WITH
COLOR OF UNIT. CONTACT
YOUR LOCAL BRADLEY REP.
FOR ASSISTANCE).
SPRAYHEAD BODY
(PART NUMBER VARIES WITH
COLOR OF UNIT. CONTACT
YOUR LOCAL BRADLEY REP.
FOR ASSISTANCE).
BOWL
(PART NUMBER VARIES
WITH COLOR OF UNIT.
CONTACT YOUR LOCAL
BRADLEY REP. FOR
ASSISTANCE).
Components
#8-32 x 3/4"
ROUND HEAD
MACHINE SCREW
(160-276)
BRACKET
(140-950)
#8 WASHER
OPTIONAL WATER HEATER
EX95TMLB, 240/208 volts
(269-1767)
EX100TMLB, 277 volts
(269-1768)
#8 NUT
110/24 VAC
CLASS II PLUG-IN
TRANSFORMER
S83-152
1/4"-20 x 1/2"
PAN HEAD
SCREW (qty. 2)
(160-389)
1/4"-20
WASHER
(qty. 2)
(142-002DB)
BOWL MOUNTING
HARDWARE

SS-2N/IR/STD, SS-2N/IR/WH Installation
412/11/07 Bradley Corporation • 215-1497 Rev. F; ECN 07-814
Supplies Required:
• (6) 3/8" wall anchors, bolts and 1" min. O.D. washers to mount main frame and bowl to wall (minimum pull-out rating of 1,000 lbs.)
• STD. HEIGHT ONLY: (2) 3/8" wall anchors, bolts and 1" min. O.D. washers to mount scuff base to wall
• 1/2" NPT hot/cold or tempered supply piping and 1-1/2" NPT drain piping
• (2) 1/2" NPT street elbows
• 110 volt GFCI protected electrical outlet for 1110/24 VAC plug-in transformer (supplied)
• OPTIONAL: 240/208-volt or 277-volt electrical box for electric tankless water heater
Dimensions - Front and Top Views
15"
(381MM)
8-5/8"
(219mm)
8"
(203mm)
RADIUS
50"
(1270mm)
38-1/4"
(972mm)
21-1/4"
(540mm)
30"
(762mm)
36"
(914mm)
7"
(178mm)
10"
(254mm)
RADIUS
15"
(381MM)

Installation SS-2N/IR/STD, SS-2N/IR/WH
Bradley Corporation • 215-1497 Rev. F; ECN 07-814 12/11/07 5
Dimensions - Side Views
34"
(864mm)
30"
(762mm)
31"
(787mm)
10-1/4"
(260mm)
27"
686mm)
WALL-HUNG
MOUNTED AT
JUVENILE HEIGHT
AGES 6 THROUGH 12
WALL-HUNG
MOUNTED AT
STANDARD HEIGHT
32"
(813mm)
11-1/4"
(286mm)
28"
(711mm)
WALL-HUNG
MOUNTED AT
TAS HEIGHT
GRADES PRE-K
THROUGH 5 OR 6
WALL-HUNG
MOUNTED AT
TAS HEIGHT
GRADES 6
THROUGH 8 OR 9
26"
(660mm)
9-1/4"
235mm)
30"
(762mm)
8-5/8"
(219mm)
13-1/4"
(337mm)
21-1/8"
(537mm)
3" (76mm)
11-1/2"
(292mm)
34"
(864mm)
30"
(762mm)
STANDARD HEIGHT
SCUFF BASE
STANDARD
HEIGHT ONLY
8-5/8"
(219mm)
13-1/4"
(337mm)
21-1/8"
(537mm)
11-1/2"
(292mm)
8-5/8"
(219mm)
21-1/8"
(537mm)
11-1/2"
(292mm)
8-5/8"
(219mm)
21-1/8"
(537mm)
11-1/2"
(292mm)
8-5/8"
(219mm)
21-1/8"
(537mm)
11-1/2"
(292mm)
38-1/2"
(978mm)
35-1/2"
(902mm)
34-1/2"
(876mm) 36-1/2"
(927mm)
38-1/2"
(978mm)
A
D
A
C
O
M
P
L
I
A
N
T
A
D
A
C
O
M
P
L
I
A
N
T
A
D
A
C
O
M
P
L
I
A
N
T
TAS TA S

SS-2N/IR/STD, SS-2N/IR/WH Installation
612/11/07 Bradley Corporation • 215-1497 Rev. F; ECN 07-814
1Rough-Ins
3-1/2"
(89mm)
20"
(508mm)
25-3/4"
(654mm)
32"
(813mm)
23-1/2"
(597mm)
9-3/8"
(238mm)
4"
(102mm)
3"
(76mm)
13-1/4"
(337mm)
15"
(381mm)
J
AA
B
B
H
B
G
B
CC
D1 D2
E
23-1/2"
(597mm)
9-3/8"
(238mm)
4"
(102mm)
19"
(483mm)
FLOOR
2" (51mm)
13"
(330mm) 22"
(559mm)
28-3/4"
(730mm)
C
L
CODE DESCRIPTION QTY.
A 3/8" Wall Anchors with a minimum pull-out force of 1,000 lbs. for Bowl 2
B 3/8" Wall Anchors with a minimum pull-out force of 1,000 lbs. for Mainframe 4
C 3/8" Wall Anchors for Base Frame, Standard Frame option only, minimum pull-out force not required 2
D1 1/2" NPT Cold Supply, stub-out 2" from wall 1
D2 1/2" NPT Hot or Tempered Supply, stub-out 2" from wall 1
E 1-1/2" NPT Drain, stub-out 2" from wall 2
F
On the bowl back, measure the distance between the 3/4" bowl mounting holes. Divide this measurement
in half. Measure and mark this dimension on the wall to the left and the right of the centerline. Install two
3/8" wall anchors with a minimum pull-out rating of 1,000 lbs (supplied by installer) at locations marked.
2
GWater Heater Option #1: Rough-in appropriate electrical supply per local code (recommended location for
240/208v or 277v electrical box [4" long x 4" wide x 8" high] shown) 1
HWater Heater Option #2: Rough-in appropriate electrical supply per local code (recommended location for
240/208v or 277v electrical box [4" long x 4" wide x 4" high] shown) 1
J 110v GFI Protected Electrical Outlet 1
RIM HEIGHT VERTICAL HEIGHT ADJUSTMENTS FOR CODES
A–E, H, C and W FIXTURE STYLE
34" None Standard Height
34" None Wall-Hung
32" Subtract 2" TAS, Grades 6 through 8 or 9
31" Subtract 3" Juvenile Height
30" Subtract 4" TAS, Pre-K through Grades 5 or 6

Installation SS-2N/IR/STD, SS-2N/IR/WH
Bradley Corporation • 215-1497 Rev. F; ECN 07-814 12/11/07 7
SCUFF PANEL
STANDARD HEIGHT
FRAME ONLY
SCUFF BASE FRAME
STANDARD HEIGHT
FRAME ONLY
2Mount Frame to Wall
3Install Bowl
Anchoring the frame to a wall that is not
flat may cause the frame to bend, making
it difficult to reinstall the access panels. If
necessary, use shims to compensate for
wall distortion.
Once you have positioned the frame such that
it is level and flat against the wall or shimmed ,
mount the frame to the wall at four places using
3/8” bolts and 1” min. O.D. washers.
NOTE: When mounting the standard height frame,
mount the scuff base to the wall at the same time
using two additional 3/8” bolts and washers.
B
AUsing a T20 torx key, remove
the fasteners securing the
access panel to the main
frame, and remove the panel.
The sprayhead body has slotted holes for adjusting the fit-up with the bowl and wall.
The tailpiece on the waste tee has been rotated upward for shipping purposes. Turn
the tailpiece down to its proper position before installing the bowl.
Secure the bowl to the
wall anchors with 3/8”
bolts and 1” min. O.D.
washers, two places.
Do not overtighten.
B
Attach the bowl to the frame with
1/4”-20 x 1/2” pan-head screws
and washers. Do not tighten.
A
Tighten the pan-head screws
Do not overtighten.
C

SS-2N/IR/STD, SS-2N/IR/WH Installation
812/11/07 Bradley Corporation • 215-1497 Rev. F; ECN 07-814
4a Connect the Supply — Hot and Cold Supply
4b Connect the Supply — Single Tempered Supply
The letter “H” on the Vernatherm™ Mixing
Valve indicates hot water supply inlet.
Loosen but do not remove
the two mounting screws
holding the valve bracket
to the frame.
Slide the valve bracket up
and lift it from the frame.
A
Connect one end of each
hose to the Vernatherm™
valve (one on the hot side,
one on the cold side).
Connect the other swivel
end to the stop/check valves.
C
Using a thread sealer, thread
the stop/check valves onto the
hot and cold wall stub-outs.
B
Loosen but do not remove the two
mounting screws holding the valve
bracket to the frame.
Slide the valve bracket up and lift
it from the frame.
A
Connect one end of flexible hose
to the tempered line adapter.
Connect the other swivel end to
the stop/check valve.
C
Using a thread sealer,
thread the stop/check
valve onto the tempered
wall stub-out.
B

Installation SS-2N/IR/STD, SS-2N/IR/WH
Bradley Corporation • 215-1497 Rev. F; ECN 07-814 12/11/07 9
6Optional Electric Tankless Water Heater
5Install the Drain
240/208 or 277 voltage is required for hot water heater.
Refer to the installation manual provided with the hot
water heater for further installation information.
Connect the 1/2" flexible
hose from the cold water
supply stub-out to the hot
water heater inlet.
B
Connect the 1/2" flexible
hose from the hot water
heater outlet to the supply
inlet on the solenoid valve
assembly.
C
Hang the water heater
on the right side frame
member.
A
To Drain
Stub-Out

SS-2N/IR/STD, SS-2N/IR/WH Installation
10 12/11/07 Bradley Corporation • 215-1497 Rev. F; ECN 07-814
7Connect Electrical and Sprayhead Supplies
Sprayhead
Components
INFRARED SENSOR
269-1608HP
Snap the transformer's
circuit plug into the female
transformer circuit plug.
B
Connect the sensor circuit
plug from the sprayhead to
the solenoid circuit plug.
A
WARNING: The Express® control must be connected with the 24 VAC Class II transformer provided. Connections
to 110 VAC can cause personal injury and will result in damage to the electronics. Connection of leads other than
shown may cause permanent damage to the sensor.
Loosen the compression nuts.
Push the sprayhead supply tubes firmly into
the tube connectors until they are fully seated.
Tighten the compression nuts by hand.
C
Reinstall the valve bracket. Turn on the water supply and check for leaks. Turn on the electrical power to the electrical outlet
and pass your hand in front of each station’s sensor until all the air is purged from the lines and water is flowing smoothly.
Reinstall the access panel.
START-UP NOTE: Wait two full minutes after making the power connection before using the lav. The sensors will take up to eight
full minutes (while not in use) to adapt to the bowl if another object is detected during the two-minute start-up period.
D
Sensor assembly and solenoid valve access
• To access sensors: Remove the Phillips-head screws located in the bottom of the sprayhead body and lift the Terreon
cover/shelf off.
•To reinstall sprayhead cover/shelf: Position the cover/shelf on the sprayhead body and secure it to the sprayhead body
using the screws provided.
Window
(269-1241)
O-Ring
(125-157)
Aerator Assembly
(S05-180)
Nut, 1/2"-14 NSPM
(110-115)
Green Supply Tube
(from Sprayhead)
Red Supply Tube
(from Sprayhead)
Red Spade Terminal
Green Spade Terminal
White Spade Terminal
White Spade Terminal