Bradley SXWS9561 User manual

Installation
SXWS9561
Stainless Steel Panel Shower
P.O. Box 309, Menomonee Falls, WI 53052-0309
Phone: 1-800-BRADLEY Fax: [phone]
http:\\www.bradleycorp.com
215-960 Rev. B; EN 05-714
© 2005 Bradley Corporation
Page 1 of 6 11/11/05
Table of Contents
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Wall Openings (no soap dish) . . . . . . . . . . . . . . .2
Wall Openings (recessed dish) . . . . . . . . . . . . . . .3
Wall Openings (surface-mount soap dish) . . . . . .3
Installation - Shower Components . . . . . . . . . . . .4
Installation - Optional Soap Dish . . . . . . . . . . . .5
Cleaning Stainless Steel . . . . . . . . . . . . . . . . . . . .6
WARNING
Read this entire installation manual to ensure proper installation. When finished
with the installation, file this manual with the owner or maintenance department.
Compliance and conformity to local codes and ordinances is the responsibility of
the installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Before installing components, all connection supply lines must be flushed and
free of foreign material such as pipe dope, chips, solder, etc. Bradley will not be
responsible for leaking valves due to the presence of foreign material, or
distorted stop gaskets where excessive pressure (above 30 lbs. of torque) has
been applied to the stop cap.
After flushing has been completed, make sure that all water supply lines have
been completely turned off before beginning installation. After installation has
been completed, turn the water supply lines back on and test the unit for leaks
and adequate water flow.
Product warranties may be found under "Product Information" on our web site at
www.bradleycorp.com.
THIS
SIDE
UP
Packing List




Installation

SXWS9561 Installation
2 11/11/05 Bradley Corporation • 215-960 Rev. B; EN 05-714
12"
(305mm)
Panel Shower Dimensions
74"
(1880mm)
TO
FINISHED
FLOOR
9" (229mm) x 4" (102mm)
Wall Openings (no soap dish)
4" (102mm) SQUARE
5" (127mm) x 10" (254mm)
OVERALL PANEL SIZE
5" (127) x 5" (127)
OVERALL PANEL SIZE
7-1/8" (181mm) x 5" (127mm)
OVERALL RECESSED
SOAP DISH SIZE
62"
(1575mm)
TO
FINISHED
FLOOR
68"
(1727mm)
TO
FINISHED
FLOOR
74"
(1880mm)
TO
FINISHED
FLOOR
72"
(1834mm)
RECOMMENDED
TO
FINISHED
FLOOR

Installation SXWS9561
3Bradley Corporation • 215-960 Rev. B; EN 05-714 11/11/05
6"
(152mm)
6"
(152mm)
74"
(1880mm)
TO
FINISHED
FLOOR
6"
(152mm)
6"
(152mm)
9" (229mm) x 4" (102mm)
6" (152mm) x 4" (102mm)
4" (102mm) SQUARE
Wall Openings (recessed soap dish)
74"
(1880mm)
TO
FINISHED
FLOOR
3-1/2"
(89mm)
9" (229mm) x 4" (102mm)
Wall Openings (surface-mount soap dish)
3/4" DIA. (2 HOLES)
SUITABLE ANCHORS
BY INSTALLER
4" (102mm) SQUARE

SXWS9561 Installation
4 11/11/05 Bradley Corporation • 215-960 Rev. B; EN 05-714
Installation - Shower Components
INSTALL CONTROL
BUTTON HERE
SHOWERHEAD PANEL
(S74-012)
THREADED ROD
(176-058)
PUSH BUTTON PANEL
(S74-017)
NUT
(161-026)
LOCKWASHER
(142-002CF)
COUPLING NUT
(110-221)
BRACKET
(159-208)
NOTE: Secure the components to
the wall from the chase side.
NOTE: Connect the valve assembly
and install the control button per
instructions included with the
components.
SHOWERHEAD
(S24-086)

Installation SXWS9561
5Bradley Corporation • 215-960 Rev. B; EN 05-714 11/11/05
Installation - Optional Soap Dish
SOAP DISH
(S03-023)
SOAP DISH
(S03-021) THREADED
ROD
(176-057)
BRACKET
(159-217)
NUT
(161-026)
OPTIONAL SURFACE-MOUNT
SOAP DISH ASSEMBLY
(S45-454) LOCKWASHER
(142-002CF)
COUPLING
NUT
(110-221)
NUT
(161-026)
LOCKWASHER
(142-002CF)
COUPLING
NUT
(110-221)
NOTE: Secure the components
to the wall from the chase side.
THREADED
ROD
(176-057)
OPTIONAL RECESSED
SOAP DISH ASSEMBLY
(S91-032)
BRACKET
(159-217)