BROSA Caledonia Rattan Bar Cabinet User manual

Caledonia Rattan
Bar Cabinet
A S S E M B LY GU I D E
V1

FOR YOUR SAFETY
Lift, don’t drag. This protects
your floor and product.
Avoid loose screws. Tighten
fixtures every few months.
Assembly requires 2 people.
It's always easier with a
friend.
Contact our support online
or call 1300 027 672.
Check the assembly guide
for required components.
?
Assembling this product on
a soft surface protects its
finish.

Components
Before you get started, check you have all of the pieces below.
If anything’s missing, we’ll sort it out right away. Simply visit:
www.brosa.com.au/pages/product-return-and-parts-request
Hardware
A x 6
(M6 x 40)
B x 6
(Ø8 x Ø25)
D x 4
(M6 x 20)
E x 4
(Ø8 x Ø25)
C x 6
(Ø8 x Ø16)
F x 1
(M4)
Body x 1
①
Leg Frame x 2
②
Rail x 2
③
Shelf x 2
④

Step 1 Fit the tongues of the rails ③into the slots of the
leg frames ②. Make sure the stickers match as
per the diagram below.
③
③
②
②

Step 2 Fit a washer E to a short bolt D. Insert the bolt
into a hole on the bracket. Screw the bolt with
your hand. Leave the bolt loosely attached.
Repeat this for the remaining brackets.
D x 4
E x 4
DE

Step 3 Align the structure formed in Step 2 with the
holes on the bottom of the body ①. Make sure
the stickers match as per the diagram below.
Fit a spring washer C to a long bolt A followed by
a flat washer B. Insert the bolt into a hole on the
leg frame. Screw the bolt with your hand and
leave it loosely attached. Repeat this for all holes
on the leg frames.
A x 6
B x 6
C x 6
C
A
B
①

Step 4 Once the structure is built up, tighten all bolts
with the Allen key F.
F x 1 F
F

Step 5 Place the completed piece of furniture the right
way up in its desired location.
Fit the shelves ④into the inner space. Rest the
shelves on the wooden rails.
④
④

Step 6 Adjust the foot stoppers to make all legs sit firmly
on the ground.

Step 7 Enjoy your new Caledonia Rattan Bar Cabinet!

It is STRONGLY RECOMMENDED to install anti-tip kit to avoid furniture
tip-over.
Anti-Tip Kit Installation
Hardware
Wall Fixings
a x 4 b x 2 cx 4 dx 4 ex 4
Wood
If fixing to wood
make sure that it
isn’t chipboard as
screws can easily
pull away from the
core structure.
Brick or Masonry
Use an appropriate
wall plug provided
you are sure your
wall is sound.
Cavity Wall
Special toggle wall
plugs are needed.
Seek expert
advice.
Because of the variety of wall compositions, we can’t provide you with
appropriate wall fixings. Please identify your wall composition and
contact your local hardware store to get the appropriate fixings.

What You Need
Attach the brackets a securely to the back top of the
unit using the short screws cprovided.
Step 1
ax 2
cx 4
ac

Determine where the piece is to be placed and mark
locations on the wall for the mounting brackets ausing a
pencil. Move the furniture out of the way so that the
brackets can then be mounted to the wall.
Step 2
Instructions below demonstrate how to attach the kit to the wall using
the wall plugs provided. But please do identify the type of your wall
and choose the appropriate wall fixings.
ax 2
a

Drill holes for the wall plugs using a drill. Knock the plugs
e into the holes using a hammer. Place the brackets
against the plugs again and fix the brackets with the long
screws d.
Step 3
dx 4
ex 4
d
e

Lace the nylon strap b down through the brackets. Slide
the thin end of the strap through the receiving end on
the nylon strap. Pull to tighten the piece of furniture snug
against wall.
Step 4
bx 2
b

1. Upon receiving your product, you might find that the door doesn’t
align well. Please note that it’s not a product flaw and can be adjusted
following the instructions below.
Troubleshooting

Loosen the screw at the end of the hinge arm.
Step 1
Gently pull the door so that it is separated from the
body.
Step 2
2. Follow the steps below to disassemble your doors when needed.
Reverse the steps above to get the doors attached again.

Pull the drawer until the levers of the drawer slides come
out as shown in the zoomed-in diagram below.
Step 1
3. Follow the steps below to detach the drawer if needed.

Press down on the lever on one side and up on the
opposite side to disengage the mechanism. Pull the
drawer out while pressing the levers.
Step 2

Line up the slides and push until you hear the “click”
indicating that slides have reengaged.
Step 1
4. Follow the step below to attach your drawer again.