BROSA Cato Chest of Drawers User manual

Cato
Chest of Drawers
ASSEMBLY GUIDE
V2

FOR YOUR SAFETY
Lift, don’t drag. This protects
your floor and product.
Avoid loose screws. Tighten
fixtures every few months.
Assembly requires 2 people.
It's always easier with a
friend.
Contact our support online
or call 1300 027 672.
Check the assembly guide
for required components.
?
Assembling this product on
a soft surface protects its
finish.

Components
Before you get started, check you have all of the pieces below.
If anything’s missing, we’ll sort it out right away. Simply visit:
www.brosa.com.au/pages/product-return-and-parts-request
① x 1 ② x 2 ③ x 1
④ x 2 ⑤ x 2 ⑥ x 1
⑦ x 2 ⑧ x 6 ⑨ x 3
⑩ x 4 11 x 1

Hardware
What You Need
A x 1
(5#)
B x 8
(M8 x 60)
C x 8
(Ø8 x Ø14)
D x 24
(Ø6 x L28)
G x 40
(Ø6 x 30)
H x 12
(M6 x 8)
I x 3
(L400)J x 1
(10g)
K x 24
AAA x 12
(M3.8 x 12)
E x 24
(Ø12 x H9)
F x 12
(M3.5 x 35)
12 x 1

Tips for Glue*
Gluing is an optional step during assembly. Decide if you want to apply
glue to wooden dowels based on the pros and cons below.
Pro: Glued wooden dowels add to the stability of the structure.
Con: Glued joint is not detachable any more.
Follow the steps below to apply glue if needed.
Fill the dowel hole with glue 1/4 full.
Step 1
Spread the glue all over the dowel hole with a stick.
Step 2
Insert the dowel into the hole and firmly press them
together.
Step 3
1 /4
*This piece of furniture will NOT be eligible for return or exchange once glued, unless faulty.
Make sure it’s the product you’re expecting before gluing.

Align a leg ⑩with the opening on the bottom of
the body 12. Fit a washer C to a bolt Band then
insert the bolt into the hole on the wooden block
to connect it with the leg. Repeat this for the
other hole. Tighten both bolts with the Allen key
A.
Repeat this for the remaining legs.
Step 1
Ax 1
Bx 8
Cx 8
⑩
12
A
BC

Align the runner Iwith the pre-drilled holes on
the inner side wall of the body and make sure the
holes on the wall are aligned with the last top
hole of each hole group on the runner. Insert the
flat end screws H into the pre-drilled holes and fix
them with a screwdriver. Repeat this for the op-
posite side and then repeat the whole process
for the remaining runners.
Step 2
Hx 12
Ix 3
H
I

With a screwdriver, drive a pointed end screw
AAA into a spare hole of each hole group to
strengthen the connection between the runner
and the side wall. Repeat this for all runners.
Note: No pre-drilled holes are provided on the
side walls for this step. Holes need to be drilled
by yourself.
Step 3
AAA x 12
AAA

Align the small drawer side walls ③ 11 with the
back wall ⑥. Fix them together with the long
screws F.
Step 4
Fx 4
③
⑥
11
F

Insert the wooden dowels Ginto the holes on the
side. Insert the cam screws Dinto the holes in the
middle and fix them with a screwdriver.
Step 5
Dx 2
Gx 4
D
G
G