BROSA Single Size Upholstered Gaslift Bed Base User manual

Single Size Upholstered
Gaslift Bed Base
ASSEMBLY GUIDE
V1

FOR YOUR SAFETY
Lift, don’t drag. This protects
your floor and product.
Avoid loose screws. Tighten
fixtures every few months.
Assembly requires 2 people.
It's always easier with a
friend.
Contact our support online
or call 1300 027 672.
Check the assembly guide
for required components.
?
Assembling this product on
a soft surface protects its
finish.

Components
Before you get started, check you have all of the pieces below.
If anything’s missing, we’ll sort it out right away. Simply visit:
www.brosa.com.au/pages/product-return-and-parts-request
Headboard x 1 Right Sideboard x 1
①②
Hardware
A x 2
(M8 x 80/40)
B x 4
(Ø8)
C x 2
(M8)
D x 1
(M8)
E x 8
(M8 x 60)
F x 8
(M8)
G x 1
(M8)
H x 1 I x 1
③
④
⑤
⑥
⑦
⑧
Left Sideboard x 1 Footboard x 1
Floor Board x 2
Wooden Support Bar x 3
Slat Set x 1
Mattress Retainer x 2
Handle x 2
⑨

Loosen the pre-attached bolts on both
sideboards ② ③ and the footboard ④using the
Allen key I but do not remove them.
Step 1
Ix 1
②
③
④
I
I

Hook the brackets to the bolts. Screw the bolts
with the Allen key I but do not tighten them yet.
Step 2
Ix 1
I
②
③
④
①
I

Adjust and make sure the frame formed in Step 2
is aligned perfectly and then tighten all bolts with
the Allen key I.
Step 3
Ix 1
I

Unscrew and remove the nut from the threaded
rod of the gas lift arm. Keep the removed nut for
the following assembly. Repeat this for the other
side.
Step 4

Lift the gas lift arm and the gas lift strut so that
the threaded rod of the arm can fit into the hole
of the strut.
Step 5

Secure the structure formed in Step 5 using the
nut removed in Step 4 with the spanner G.
Repeat the process for the other side.
Step 6
Gx 1
G

Fit the wooden support bars ⑥into the slots.
Step 7
⑥

Place the floor boards ⑦on top of the wooden
support bars.
Step 8
⑦

Unfold the slat set ⑤ to make a full-size slat set.
Step 9
⑤

Place the slat set on a level protected surface,
making sure the underside is facing you.
Fit a flat washer B to a long bolt A. Insert the bolt
from one side of the middle bars, making sure it
protrudes from the other side.
Fit a flat washer Band a nut C to the bolt from
the other side. Tighten the nut with the spanner
D.
Step 10
Ax 2
Bx 4
Cx 2
Dx 1
A
B
B
C
D

Flip the slat set the right way up and align it with
the holes on the gas lift arms.
Insert bolts Einto corresponding holes on the
slat set frame. Attach flange nuts F onto the bolts
from the other side and fix them with the
screwdriver Hand spanner G.
Step 11
Ex 8
Fx 8
Gx 1
Hx 1
E
F
G
H

Attach both handles ⑨to the end of the slat set
frame.
Step 12
⑨

With a friend, push the slats down. It requires a
fair amount of strength because there isn’t a
mattress on the slats to add weight yet.
Step 13

The rubber blocks on the mattress retainer ⑧
can be rotated into different positions. Rotate
both rubber blocks to be horizontally longer.
Repeat this for the other retainer.
Clip the mattress retainers to proper spots on the
front end of the slat set frame from inside as
shown in the diagram below.
Step 14
⑧

Enjoy your new Single Size Gaslift Bed Base!
Step 15

1. Please do NOT sit on the bed frame without a mattress.
Warning
2. The maximum loading weight for the bed base is 250kg. Please do
NOT exceed the weight limit.
MAX.
250 KG

3. Please always use the handles to lift and lower the bed frame to
avoid trapping your fingers. Always use both hands.