CDVI CDV97-1ID User manual

USER MANUAL
RF CARD RF CARD
RF CARDRF CARD
2 WIRE SYSTEM
Fisheye door station with proximity access control
CDV97-V1 / 201609
CDV97 Series
CDV97-4IDCDV97-1ID CDV97-2ID
CDV17-97A
Please read carefully to ensure safe and correct operation
Keep this manual safe for future use

CONTENTS
PARTS AND FUNCTIONS..................................................................................... 3
Part Names............................................................................................................. 3
Mounting................................................................................................................. 4
BASIC FUNCTIONS .............................................................................................. 6
Unlock Operations.................................................................................................. 6
Fisheye Camera ..................................................................................................... 6
External Motion Detection ...................................................................................... 6
SETUP INSTRUCTIONS........................................................................................ 7
Functions Setting Up .............................................................................................. 7
Setting Door Station Address ................................................................................. 8
Setting Door Station Calling Mode ......................................................................... 8
Setting Camera Resolution.................................................................................... 10
Setting Unlock Mode ............................................................................................. 10
Setting Unlock Time............................................................................................... 11
Setting Nameplate Illumination Mode.................................................................... 11
Setting Night View LED Illumination Mode............................................................ 12
Setting Ring-back Tone ......................................................................................... 12
Setting Image Display Mode.................................................................................. 13
Registering ID Card............................................................................................... 14
WIRING ................................................................................................................. 17
Connecting Electric Lock....................................................................................... 17
Connecting Basic One-to-one ............................................................................... 18
Connecting Multi Door Stations............................................................................. 18
Connecting Multi Monitors..................................................................................... 19
APPENDIX ............................................................................................................ 21
Precautions............................................................................................................ 21
Specication .......................................................................................................... 21
Cables and Requirements..................................................................................... 22

-3-
Part Names
PARTS AND FUNCTIONS
[11]
[10]
[14]
[9]
[1]
[3]
[4]
[1]
[3]
[4]
[8]
[7]
[6]
[5]
[9]
[8]
[7]
[6]
[5]
[12]
[11]
[12]
[13]
[13]
[2]
[2]
Surface mounted
Flush mounted
[1] Microphone
[2] UNLOCK indicator
[3] CALL indicator
[4] Call button
[5] Nameplate
[6] Front panel
[7] Speaker
[8] Night view LED
[9] Camera lens
[10] Rain Shield
[11] Mounting hook
[12] Connection port
[13] Screw hole
[14] Mounting box

-4-
PARTS AND FUNCTIONS
Mounting
1 2 3 4 5
AcDbMLeader (ACDB_MLEADER_CLASS)
AcDbMLeader (ACDB_MLEADER_CLASS)
Rainy cover
Rainy cover
The distance between
the top of main unit
and rain cover should
be not less than 3mm.
Main unit
Main unit
≥3mm
1 2 3 4 5
AcDbMLeader (ACDB_MLEADER_CLASS)
AcDbMLeader (ACDB_MLEADER_CLASS)
AcDbMLeader (ACDB_MLEADER_CLASS)
1. Connect the cable correctly.
Surface mounted
Flush mounted
* The camera angle view of surface mount model may be less than 1700.
The installation height is suggested at 145~160cm.
3. Install the name plate.
4. Attach the front panel to the main unit.
5. Use the special screwdriver and the screws to x the panel.
1. Drill a hole in the wall to match the size of mounting box, then attach the mounting box to the
wall.
2. Loosen the high screws to install the name plate.
3. Connect the cable correctly.
4. Attach the front panel to the mounting box, then use the special screwdriver and the screws to
x the panel.
5. Finish the installation.
2. Drill holes in the wall to match the size of screw wall plugs,then attach the rain shield
and main unit to the wall, the distance between the top of main unit and rain cover should not be
less than 3mm.

-5-
PARTS AND FUNCTIONS
Terminal description
Lock Control Jumper: To select the lock type.
Motion Detector Connect Port: To connect external PIR motion detector.
Main Connect Port: To connect the bus line and the electronic locks.
• L1,L2: Connect to the bus line, no polarity.
• PL: External lock power input, connect to the power positive(power +).
• S+: Lock power(+) output.
• S-: Lock power(-) output, connect to the power(-) input of locks(only when using the door
station to power the locks, if using the external power supply for the locks, the S- will not be
connected).
1 2 3
Lock Control Jumper
PIR Motion Detector
Connect Port
+12V
GND
PIR
L1 L2
PL
S+ S-
Main Connect Port

-6-
BASIC FUNCTIONS
Unlock Operations
Fisheye Camera
External Motion Detection
Standard
door station angle
DT607
1700door camera angle
(Wide angle view shown)
12V
GND
PIR
Unlocking by ID Card/Tag
When the registered user card is shown to the ID card window, the UNLOCK indicator lights up,
the buzzer sounds,and the electric door strike is unlocked.
• Present an unauthorized user card, the buzzer will beep three times
• Present an authorised user card, the buzzer will beep once, the UNLOCK indicator will
light up and the connected lock will release.
Please note that this function requires a
monitor with sheye function support.
The angle view is 1700,visitors within this
angle of view can be seen clearly zoom can
also be used to view individuals in close up
via the indoor monitor with sheye function.
If the external motion detector is connected
to the system the following functions will be
effective:
'When detecting someone passing by, the door
station can be set to unlockor turn on a light.
* Please contact your supplier for more details regarding detector connection.
The door station is equipped with terminalsto
enable connection of an external motion
detector*.
Motion
detector*

-7-
SETUP INSTRUCTIONS
Functions Setting Up
KEY_1
KEY_2
KEY_3
KEY_4
KEY_SET
LED_UNLOCK
LED_TALK
LED_NAME
RF CARD
Order Setting items Setting range Default value
1 Setting door station address 0~3 0
2Setting door station
calling mode Standard/Group calling mode Standard calling mode
3 Setting camera resolution High/Low High
4 Setting the unlock mode 0:opened/1:closed 0:opened
5 Setting the unlock time 01 to 99 seconds 1 seconds
6Setting the nameplate
illumination mode On/Off/Auto On
7Setting night view LED
illumination mode On/Off/Auto Auto
8 Setting ring-back tone
Ringing one time
Ring continuously
No ring-back tone
Ringing one time
9 Setting image display mode
Alternate switching mode
Zoom mode
Full screen mode
Alternate switching mode
This section explains the settings of each
function. Please refer to the following table:
Each operation is indicated by the lighting
of the LED indicator on the unit and by the
sounding of the buzzer.
To perform the settings for the function
required,remove the metal front panel to
gain access to the 'Key Set' button.
Please refer to the diagram (right).

-8-
Setting Door Station Address
Setting Door Station Calling Mode
UNLOCK Indicator:OFF
TALK Indicator:OFF Buzzer Beep+, Beep
UNLOCK Indicator:OFF
TALK Indicator:OFF
Buzzer Beep+
In standby mode, press
KEY_SET button once
Press KEY_1 button to set
the first door station.
Press KEY_2 button to set
the second door station.
Press KEY_3 button to set
the third door station.
Press KEY_4 button to set
the fourth door station.
UNLOCK Indicator:OFF
TALK Indicator:OFF
Buzzer Beep,Beep
UNLOCK Indicator:OFF
TALK Indicator:OFF
Buzzer Beep,Beep,Beep
UNLOCK Indicator:OFF
TALK Indicator:OFF
Buzzer Beep,Beep,Beep,Beep
SETUP INSTRUCTIONS
A total of 4 addresses can be congured. They can be modied either before or after
installation. 0 is default, to change the setting, please use the following steps:
ID=0,1st door station ID=1,2nd door station ID=2,3rd door station ID=3,4th door station
• While in the setting mode, the address of door station can be changed by pressing KEY1~4 freely.
• The LED_NAME indicator will continually flash while in the setting mode.
• If no operation is carried out within 10 s the setting mode will exit automatically.
• To exit the setting mode manually press the KEY_SET button four times.
There are two calling modes for door station, Standard calling mode and Group calling
mode. Please note that the door station operates in Standard calling mode by default.

-9-
SETUP INSTRUCTIONS
UNLOCK Indicator:OFF
TALK Indicator:ON
Buzzer Beep+, Beep
UNLOCK Indicator:OFF
TALK Indicator:ON
Buzzer Beep+
Press KEY_1 button to
activate Standard calling
mode for door station.
UNLOCK Indicator:OFF
TALK Indicator:ON
Buzzer Beep, Beep
Press KEY_1 button again
to activate Group calling
mode for door station.
Press KEY_1
A
B
C
D
A A
B
RF CARDRF CARD
Call button A: callsmonitor address 01 by default.
Call button B: calls monitor address 02 by default.
Call button C: callsmonitor address 03 by default.
Call button D: callsmonitor address 04 by default.
2. Group calling mode
1. Standard calling mode(Address range 01-04
by default)
Call button A: Callsall the monitors in the group
address 00~15.(One monitor must be set to 00)
Call buttons B,C,D: Callsall the monitors in the group
address 16~31.(One monitor must be set to 16)
* For more details regarding code settingsfor the monitor, please refer to corresponding user manual .
To change the call setting, please follow the steps:
In standby mode, press
KEY_SET button twice.
• If no operation is carried out within 10 s the setting mode will exit automatically.
• To exit the setting mode manually press the KEY_SET button four times.
• The LED_NAME indicator will continually flash while in the setting mode.
• While in the setting mode, the calling code can be changedmode by pressing KEY1 cyclically.
Each call button will respond different addresses when set in different calling mode. Refer to the
following for more information.

-10-
Setting Camera Resolution
Setting Unlock Mode
High resolution is default, to change the setting, please follow the steps:
UNLOCK Indicator:OFF
TALK Indicator:ON
Buzzer Beep+, Beep
In standby mode, press
KEY_SET button twice.
UNLOCK Indicator:OFF
TALK Indicator:ON
Buzzer Beep+
Press KEY_2 button to set the
camera to High resolution.
UNLOCK Indicator:OFF
TALK Indicator:ON
Buzzer Beep, Beep
Press KEY_2 button again
to set the camera to Low
resolution.
Press KEY_2
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep+, Beep
In standby mode, press
KEY_SET button three
times.
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep+
Press KEY_1 button to set
the unlock mode to
Normally opened.
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep, Beep
Press KEY_1 button again
to set the unlock mode to
Normally closed.
Press KEY_1
SETUP INSTRUCTIONS
The resolution of the camera can be changed between high and low quality at the door station.
• If no operation is carried out within 10 s the setting mode will exit automatically.
• To exit the setting mode manually press the KEY_SET button four times.
• While in the setting mode, the calling code can be changedmode by pressing KEY2cyclically.
• The LED_NAME indicator will continually flash while in the setting mode.
There are 2 unlock modes, Normally open and Normally closed.
Normally open is default, to change the setting, please follow the steps:
• If no operation is carried out within 10 s the setting mode will exit automatically.
• To exit the setting mode manually press the KEY_SET button four times.
• While in the setting mode, the lock mode can be changedmode by pressing KEY1 cyclically.•
The LED_NAME indicator will continually flash while in the setting mode.

-11-
Setting Nameplate Illumination Mode
Setting Unlock Time
SETUP INSTRUCTIONS
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep+, Beep
In standby mode, press
KEY_SET button three
times.
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep,Beep......
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep+, Beep
In standby mode, press
KEY_SET button three
times.
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep+
Press KEY_3 button to set
the nameplate illumination
mode to Normally on.
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep, Beep
Press KEY_3 button again
to set the nameplate illumina-
tion mode to Normally off.
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep, Beep,Beep
Press KEY_3 button again
and again to set the nameplate
illumination mode to Auto.
Press KEY_3
By default, the unlock time is 1s, this can be changed between 1s~99s.
Follow the steps below:
• If no operation is carried out within 10 s the setting mode will exit automatically.
• To exit the setting mode manually press the KEY_SET button four times.
There are 3 illumination modes for the nameplate indicator, Normally on,Normally off and
Auto. Normally on is default, to change this setting please use the following steps:
• While in the setting mode, the calling code can be changedmode by pressing KEY 3 cyclically.
• The LED_NAME indicator will continually flash while in the setting mode.
Press and hold on KEY_2
button. The time held on is
the new unlock time.
• While holding Key 2 to enter the unlock time,a beep will be heard for each second.
• The LED_NAME indicator will continually flash while in the setting mode.
• If no operation is carried out within 10 s the setting mode will exit automatically.
• To exit the setting mode manually press the KEY_SET button four times.

-12-
Setting Night View LED Illumination Mode
SETUP INSTRUCTIONS
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep+, Beep
In standby mode, press
KEY_SET button three
times.
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep+
Press KEY_4 button to set
the night view LED mode
to Normally on.
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep, Beep
Press KEY_4 button again
to set the night view LED
mode to Normally off.
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep, Beep,Beep
Press KEY_4 button again
and again to set the night
view LED mode to Auto.
Press KEY_4
UNLOCK Indicator:ON
TALK Indicator:ON
Buzzer Beep+, Beep
In standby mode, press
KEY_SET button four
times.
UNLOCK Indicator:ON
TALK Indicator:ON
Buzzer Beep+
UNLOCK Indicator:ON
TALK Indicator:ON
Buzzer Beep, Beep
UNLOCK Indicator:ON
TALK Indicator:ON
Buzzer Beep, Beep,Beep
Press KEY_1 button again
and again to close ring-back
call tone.
Press KEY_1
There are 3 working modes for night view LED indicator, Normally on,Normally off and Auto.
Auto is default, to change the setting, please use the following steps:
• While in the setting mode, the calling code can be changedmode by pressing KEY 4 cyclically.
• The LED_NAME indicator will continually flash while in the setting mode.
Setting Ring-back Tone - (Call repeat Tone)
With ring-back tone set, pressing the call button to call a monitor will a result in a tone being
heard at door station.
• If no operation is carried out within 10 s the setting mode will exit automatically.
• To exit the setting mode manually press the KEY_SET button four times.
Ring continuously is the default setting, to change the setting, please use the following steps:
• If no operation is carried out within 10 s the setting mode will exit automatically.
• To exit the setting mode manually press the KEY_SET button four times.
• While in the setting mode, the calling code can be changedmode by pressing KEY1 cyclically.
• The LED_NAME indicator will continually flash while in the setting mode.
There are 3 ring-back call tone settings, Ring Continuously,Ring Once and No ring-back
tone.
Press KEY_1 button to set
the ring-back call tone ringing
continuously.
Press KEY_1 button again
to set the ring-back call tone
ring once.

-13-
Setting Image Display Mode
UNLOCK Indicator:ON
TALK Indicator:ON
Buzzer Beep+, Beep
In standby mode, press
KEY_SET button four
times.
UNLOCK Indicator:ON
TALK Indicator:ON
Buzzer Beep+
Press KEY_2 button to set
the image display mode
to Cycle switching.
UNLOCK Indicator:ON
TALK Indicator:ON
Buzzer Beep, Beep
Press KEY_2 button again
to set the image display
mode to Zoom mode.
UNLOCK Indicator:ON
TALK Indicator:ON
Press KEY_2
Buzzer Beep, Beep,Beep
Press KEY_2 button again
and again to set the image
display mode to Full screen.
During setting mode, press KEY-2 to switch Cycle switching mode, Zoom mode and Full screen mode in cycle.
SETUP INSTRUCTIONS
Please note this setting is only for monitors that do not support manual pan, tilt and
zoom functions, i.e. CDV47M, CDV43 & CDV24.
When calling a monitor:
When a call is placed from door station to a monitor, the image is displayed on screen. There
are 3 modes for the image that can be displayed;Alternate switching mode,Zoom mode
and Full screen mode.
Alternate switching mode: when the monitor is called, the image will switch between Full
screen and Zoom image at a time interval of 5 seconds.
Full screen mode: when the monitor is called, the image will be displayed in Full screen.
Zoom mode: when the monitor is called, the image will be displayed on full screen for 5
seconds, then switch to Zoom image.
Alternate switching mode is the default.To change the setting, please use the following steps:
• If no operation is carried out within 10 s the setting mode will exit automatically.
• To exit the setting mode manually press the KEY_SET button four times.
• While in the setting mode, the calling code can be changedmode by pressing KEY 2 cyclically.
• The LED_NAME indicator will continually flash while in the setting mode.
When answering the call:
When answering the call, the image switching reminder can be activated or deactiviated.
If set to activated,the image switching reminder will be different for each image display mode,
see below.
Alternate switching mode: When answering the call, image switching reminder is not shown.
Zoom mode: When answering the call, the image will be displayed on full screen for 5 sec-
onds, then switch to Zoom image as a reminder to enter the talk status.

-14-
UNLOCK Indicator:ON
TALK Indicator:ON
Buzzer Beep+, Beep
In standby mode, press
KEY_SET button four
times.
UNLOCK Indicator:ON
TALK Indicator:ON
Buzzer Beep+
Press KEY_3 button to
activate image switching
when answering the call.
UNLOCK Indicator:ON
TALK Indicator:ON
Buzzer Beep, Beep
Press KEY_3
Registering ID Card
• Card reading distance is less than 3cm.
• EM card, 125kHz.
Authorizing master cards:
SETUP INSTRUCTIONS
Full screen mode: When answering the call, the image will be displayed on Zoom mode for 5
seconds, then switch to Full screen as a reminder to enter the talk status.
If deactivated, no image switching reminder is displayed on any image display mode.
Activated is default, to change the setting, please use the following steps:
• If no operation is carried out within 10 s the setting mode will exit automatically.
• To exit the setting mode manually press the KEY_SET button four times.
• While in the setting mode, the calling code can be changedmode by pressing KEY 3 cyclically.
• The LED_NAME indicator will continually flash while in the setting mode.
• Cards = Tags
• A maximum of 320 user cards can be registered by the door station.
• Straight forward management with LED status and sound hints.
• There are two master cards, one MASTER CARD ADD
and one MASTER CARD DELETE.When registering new master
cards the exisiting master cards are invalidated automatically.
• The master cards are necessary when you add or delete user
cards. Please keep safe for future use.
By default there are two master cards marked MASTER CARD ADD and MASTER CARD
DELETE,new master cardscan be authorised by users at any time. This means any two user
cards can be authorised as master cards. When registered new master cards, the exisiting master
cards will be invalidated automatically.
Press KEY_3 button again to
deactivate image switching
when answering the call.

-15-
SETUP INSTRUCTIONS
Switching Access Control:
UNLOCK Indicator:OFF
TALK Indicator:ON
Buzzer Beep+, Beep
Show the master card of
MASTER CARD ADD to ID
card window in standby.
UNLOCK Indicator:ON
TALK Indicator:ON
Buzzer Beep+, Beep
Show the master card of
MASTER CARD DELETE
to ID card window.
UNLOCK Indicator:OFF
TALK Indicator:OFF
Buzzer Beep+
Show the master card of
MASTER CARD DELETE
again to switch as a door
station access control.
UNLOCK Indicator:OFF
TALK Indicator:OFF
Buzzer Beep+,Beep
UNLOCK Indicator:Blink two times
TALK Indicator:OFF
Buzzer Beep,Beep
Show the first card to ID
card window, set the card
of MASTER CARD ADD.
UNLOCK Indicator:Blink three times
TALK Indicator:OFF
Buzzer Beep,Beep,Beep
Show the second card to ID
card window, set the card of
MASTER CARD DELETE.
UNLOCK Indicator:OFF
TALK Indicator:OFF
Buzzer Beep+, Beep
UNLOCK Indicator:Blink one time
TALK Indicator:OFF
Buzzer Beep+
Press KEY_2 button.
Power on, within 10s,press
and hold KEY_SET button
for 3s.
• The LED_NAME indicator will continually flash while in the setting mode.
• If no operation is carried out within 10 s the setting mode will exit automatically.
• The door station will exit the setting mode after showing both cards, The UNLOCK & TALK will turn off.
• If no operation is carried out within 10 seconds, the setting mode will exit automatically.
• If current access is controlled by door station, the next access setting will controlled by CDV-ACC.
Show the master card of
MASTER CARD DELETE
again to switch to
CDV-ACC controlled.
Access can be controlled by the door station or CDV-ACC, to change the access function.
please use the following steps.

-16-
Adding User Cards:
UNLOCK Indicator:OFF
TALK Indicator:ON
Buzzer Beep+, Beep
Show the master card of
MASTER CARD ADD to ID
card window in standby.
UNLOCK Indicator:OFF
TALK Indicator:Blink one time
Buzzer Beep+
Show user cards to be
added in sequence.
UNLOCK Indicator:OFF
TALK Indicator:OFF
Buzzer Beep, Beep+
Show the master card of
MASTER CARD ADD again
to exit.
SETUP INSTRUCTIONS
Deleting User Cards:
Initializing Access (delete all user cards):
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep+, Beep
Show the master card of
MASTER CARD DELETE to
ID card window in standby.
UNLOCK Indicator:Blink one time
TALK Indicator:OFF
Buzzer Beep+
Show user cards to be
deleted in sequence.
UNLOCK Indicator:OFF
TALK Indicator:OFF
Buzzer Beep, Beep+
Show the master card of
MASTER CARD DELETE
again to exit.
UNLOCK Indicator:ON
TALK Indicator:OFF
Buzzer Beep+, Beep
Show the master card of
MASTER CARD DELETE to
ID card window in standby.
UNLOCK Indicator:ON
TALK Indicator:ON
Buzzer Beep+, Beep
UNLOCK Indicator:Blink for some time
TALK Indicator:Blink for some time
Buzzer Beep
Show the master card of
MASTER CARD ADD again,
format is activated.
Show the master card of
MASTER CARD ADD to ID
card window.
• If no operation is carried out within 10 seconds, the setting mode will exit automatically.
• To add user cards the door station must be set for access. See page 15.
• If no operation is carried out within 10 seconds, the setting mode will exit automatically.
• To add user cards the door station must be set for access. See page 15.
• If no operation is carried out within 10 seconds, the setting mode will exit automatically.
• To add user cards the door station must be set for access. See page 15.
• At step 3, the UNLOCK & TALK indicator will flash constantly until formatting is nished.
• When formatting is nished, UNLOCK & TALK indicator will turn off , a “ Beep+ ” will be heard, and
door station will exit the setting mode automatically.

-17-
Connecting Electric Lock
Door Lock Controlled with Internal Power
Door Lock Controlled with Dry Contact
3.The jumper should be placed on position
2 and 3 before connecting.
1.The external power supply must be used
• Power-on-to-unlock type:Unlock
Mode=0 (by default)
• Power-off-to-unlock type:Unlock
Mode=1
EB
*
LOCK
Jumper position on 2&3
1 2 3
L1 L2 PL S+ S-
Take off the jumper
1 2 3
L1 L2 PL S+ S-
LOCK
POWER
SUPPLY
WIRING
1.Electronic lock of Power-on-to-unlock
(fail Secure) type should be used.
4.The door lock control is not timed from
Exit Button(EB).
2.The door lock is limited to 12V, and hold-
ing current must be less than 250mA.
according to the lock requirements.
2.The internal relay contact is restricted
to 230Vac 1A or 24Vdc 1A.
3.The jumper must be taken off before
connecting.
* CDV-RLC relay actuator is required for 2nd lock connection.
5.The Unlock Mode is set to 0 (by
default).
4.Set the Unlock Mode according to
different lock types.

-18-
WIRING
about the address setting of door stations.
Connecting Basic One-to-one
Connecting Multi Door Stations
BUS(IM) BUS(DS)
-
+
L1 L2 PL S+ S-
ID=0
Code=1, DIP6=on
1 2 3 4 5 6
ON DIP
L2
L1
DIP Switches
RF CARD
PC6A
AC~
100~240VAC
100~240VAC
DBC4A1
A B C D
OFF
ON
Impedance
switch
BUS(IM) BUS(DS)
PC6A
AC~
ID=0
1st door station
ID=1
2nd door station
ID=2
3rd door station
ID=3
4th door station
L1 L2 PL S+ S- L1 L2 PL S+ S- L1 L2 PL S+ S- L1 L2 PL S+ S-
To monitors
RF CARD RF CARD RF CARD RF CARD
• The door station work in Standard mode in this example. Refer to Page 9 in detail.
• The door station is also compatible with other monitors which are provided by our company.
• Max.4 door stations can be connected to the system.
• Ensure the correct address is set for each door station, Refer to Page 8 for more details

-19-
Basic IN-OUT Wiring in Standard Mode
Connecting Multi Monitors
WIRING
ID=0
Code=1, DIP6=off
(Master)
Code=1, DIP6=off
(Slave 2)
Code=1, DIP6=on
(Slave 3)
BUS(IM) BUS(DS)
PC6A
AC~
100~240VAC
Code=1, DIP6=off
(Slave 1)
RF CARD
• The door station is also compatible with
other monitors within the 2Easy range.
• Please set door station into group calling
mode if there is more than 4 monitors in
villa (house or apartment).
Refer to Page 9.
• A distributor is unnecessary in full audio
system, and Daisy Chain connection is
recommended.
• For the last monitor connected to the
system, DIP6 should set to ON (EOL =
End of Line)
SCU camera module(max.4)
GSM module(mobile phone transfer)
SCU GSM
Optional functional modules:

-20-
WIRING
DBC4A1
A B C D
RLC DBC4A1
OFF ON
Impedance
switch
BUS(IM) BUS(DS)
Code=1，DIP6=on Code=2，DIP6=on
Code=3，DIP6=on Code=4，DIP6=on
ID=0
RF CARD
PC6A
AC~
100~240VAC
BDU
BDU bus amplifier module
RLC staircase light controller module
DBC4A1 2/4 inputs branch distributor
Star Topology Wiring With DBC4A1 in Standard Mode
• The door station is also compatible with other monitors from the 2Easy range.
Optional functional modules:
• The system can be extended up to 3 slave monitors for each monitor. It is recommended to
use extra distributor CDV-DBC4A for the extension.