CDVI 2Easy CDV4796KP-DX User manual

01628 531300 www.cdvi.co.uk
The installer’s choice
CDV4796KP-DX KIT MANUAL

The installer’s choice
IMPORTANT:
Limitations of this manual: This is provided to allow basic
installation and set up of this kit, for advanced features please
see device manuals included in each product box.
Note: For WiFi Set up please see the CDV47DX manual Pg. 21
1. Kit Contents
2. CDV96KP Parts and Functions
2.1: Terminals Description & Dip Switches
2.2: Installation
3. CDV-PC6 Parts and Functions
3.1: Product Description
3.2: Terminals Description
4. CDV47DX Part and Functions
4.1: Terminals & Installation
4.2: Mounting
4.3: Main menu
4.4: Installer Setting
4.5: User Code (Monitor ID/Address) setting
4.6: Unlock Time Setting
4.7: Unlock Mode setting
5. Schematics & Wiring
5.1: Basic Bus Wiring
5.2: Multiple Door Panel Bus Wiring
5.3: Parallel (daisy/In-out) Bus Wiring
5.4: Star Bus Wiring
5.5: Lock Connections
5.6: Setting A User Code(PIN)
6: Specifications
6.1: CDV96KP
6.2: CDV-PC6
6.3: CDV47DX
7: Cable Requirements
1 x CDV96KP - 1 Button Video Entry Panel c/w Keypad
1 x CDV-PC6 - Power/Bus Combiner
1 x CDV47DX - TFT Touch screen Internal Monitor
1 x 145mm Din Rail
1 x CDV4796KP-DX Kit Manual
1. CDV4796KP-DX KIT CONTENTS

The installer’s choice
2.1: Terminal Descriptions
2: CDV96KP Parts and Functions
30 mm
1
4 5 6
8 9
0 #
7
2 3
*
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
CDV96KP
Rain Cover
[7] Microphone
[8] Power LED
[4] Touch keypad
[5] Keypad LED
[6] Call button
[1] Camera lens
[2] Camera LED
[3] Speaker
1 2 3
Lock Control Jumper
L1
PL
S1+ GND
Main Connect Port
L2
•
•S1+,GND: Lock power connection port.
Main Connect Port: For connection of the
bus line and the electronic locks.
•Lock Control Jumper: To select the lock
type.
•PL: External lock power input
• L1,L2: Bus line connection,no polarity

The installer’s choice
3: CDV-PC6A Parts and Functions
The PC6A is a power/bus combiner unit, which is designed for the CDV 2Easy 2 wire
system to supply power for the external station, internal monitor and other accessories
on the bus. It can operate as a normal power/bus combiner or auxiliary PSU. The
features are as follows:
3: Mounting
3.1:Description
• Universal AC input/full range
• Multi protection: short circuit, overload, over voltage
• Integrated with CDV-DPS (power separator)
• Support up to 4 to 8 monitors (dependent on models)
• DIN Rail Mounting
1 2
3 4
Drill holes in the wall to match the size of
screws and attach the rain cover to the wall.
Connect the wiring (see pg 4)
Attach the panel to the rain cover Using ascrewdriver secure
the panel

The installer’s choice
LED
CN
1 2 3
BUS(IM) BUS(DS)
N LPG L
100~240 Vac
PG NLL
CN
1 2 3
BUS(IM) BUS(DS)
AC Input
100~240Vac
N LPG L
*
Note:
1. The AC cable is not included in the
package, it must comply to the specific
requirements of country where installed.
PG: Earth ground terminal.
N: AC input terminal.
L: AC input terminal.
LED: Power indicator, on when power connected.
CN: Bus control terminal.
BUS(IM): Indoor monitor connection terminal.
BUS(DS): Door station connection terminal.
Open the AC cover:
1. Push the cover base towards
the centre with your fingers;
2. Lift up and pull out the cover.
After connecting the AC cable, it is
advised to replace the cover.
2. Pins 1&2 should be short-circuited
with a C3-3P link (included in the
package),if the unit operates as a standard
power combiner. If operating as an
auxiliary power combiner, the link should
be removed.
Connect to monitor Connect to door station
3.2:Terminal Descriptions

The installer’s choice
145~160 cm
Mounting screw
x 2(included)
The unit
Mounting box
(size:86x86mm)
Mounting bracket
2 wire cable
USB-Wi-Fi adaptor
1 2 3 4 5 6
ON DIP
L2
L1
DIP Switches
SW+
SW-
RING
GND
NC
1 2 3 4 5 6
ON DIP
4: CDV47 Parts and Functions
L1,L2: Bus line terminal.
4.1:Terminal description
4.2: Mounting
SW+,SW-: Doorbell input
connection port.
Ring,GND: Extension buzzer input
connection port.
NC: Reserved.
DIP switchesBit1~Bit5: Reserved.
Bit6: Video impedance matching
switch.
Set to ON if the monitor is at the
The installation height is suggested to 145~160cm.
1. Use screws to fasten the mounting bracket to the wall with a standard
single gang ush light switch back box.
2. Connect the 2 wire cables to the unit.
3. Mount the unit to the mounting bracket, make sure the unit is securely
attached to the mounting bracket.
end of the line or operates with
CDV-DBC4, otherwise, set to
OFF.

The installer’s choice
Icon Meaning Description
SIP server connection active
and congured
Touch to enter SIP server information interface
in shortcut.
SIP server connection disabled
SIP server connection active and
not connected
Light
Touch to trigger an optional
RLC unit to operate the
light function.
Wi-Fi status
Touch to enter
Wireless setting
options.
SIP cong
Touch to enter SIP cong
interface.
Intercom
Touch to enter intercom
selections.
Monitor
Touch to view outdoor scene.
Call Record
Touch to see calling in/calling
out records or missed calls .
Setting
Press to enter setup interface.
Close
Touch to turn off the screen and
make the monitor in standby
mode.
Call Scene
Touch to activate the functions
of No disturb, Divert call.
Touch this icon to directly
enable the indicated function.
Current date and time.
Touch to enter the date
time set interface.
Status bar
Function status
Touch Unlock button, or touch anywhere of the screen on monitor in standby mode, the
Main menu will appear as follow:
The Main menu is your starting point for using all the applications on your monitor.
Touch to review the missed call in shortcut.
Touch to enter Call Scene interface in shortcut.
No disturb Displayed when the function activated
Displayed when there is missed call
Missed call
6
4.3: Main Menu
Call transfer

The installer’s choice
Icon Meaning Description
Wi-Fi connection active and not
connected
Touch to enter Wi-Fi setting interface in shortcut.
Wi-Fi connection active and
congured
Wi-Fi connection disabled
Setting
Call Tune
General
Installer
Wireless
About
Current addtess [01]
Intercom enable Enable
IPC Setting
Monitor list manage
System settings
Current address
26
Setting
Setting
Call Tune
General
Installer
Wireless
About
Current addtess [01]
Intercom enable Enable
IPC Setting
Monitor list manage
System settings
Touch to set the user code for each monitor.
1. Enter the code by touching the digital number.
2. Touch "OK" to save the code setting, complete and exit.
Notes: 1. If dip switches 1-5 are set the monitor will show the "Dip switch setting page"
2. A maximum of 32 ID's can be set; 0 to 31.
This section contains the device address setting and system settings.
1. Touch to enter installer setting interface.
4.4:Installer Settings
4.5:Users code setting

The installer’s choice
Current addtess [01]
IPC Setting
Monitor list manage
System settings
FW upgrade
Unlock time [03]
Unlock mode [Open]
Auto reboot [Enable]
Reboot
Installer Installer
Call Tune
General
Installer
Wireless
About
Call Tune
General
Installer
Wireless
About
Unlock time
08
Open
Close
Installer
Unlock mode
Setting the unlock mode.
Current addtess [01]
IPC Setting
Monitor list manage
System settings
FW upgrade
Unlock time [03]
Unlock mode [Open]
Auto reboot [Enable]
Reboot
Installer Installer
Call Tune
General
Installer
Wireless
About
Call Tune
General
Installer
Wireless
About
Setting the unlock time.
4.7: Unlock Mode Setting
The unlock time can be changed by
yourself at any time. It can be set from
01 to 99 seconds.
There are two unlock modes:
1.power-on- to-unlock type =Open
2.power-o󰀨-to-unlock =Close.
4.6: Unlock Time Setting

The installer’s choice
5.1: Basic Connection
5.2: Multi Door Stations Connection
5: System Wiring and Connections
BUS(IM) BUS(DS)
PC6A
AC~
-
+
L1 L2 PL S1+ GND
Doorbell Button
Switch
Code=00, DIP6=on
1 2 3 4 5 6
ON DIP
L2
L1
DIP Switches
100~240VAC
DBC4A1
A B C D
OFF
ON
Impedance
switch
BUS(IM) BUS(DS)
PC6A
AC~
4# Camera
L1 L2 PL S1+ GND L1 L2 PL S1+ GND L1 L2 PL S1+ GND L1 L2 PL S1+ GND
(Device Address:3)
3# Camera
(Device Address:2)
2# Camera
(Device Address:1)
1# Camera
(Device Address:0)

The installer’s choice
ID=0
Code=1, DIP6=off
(Master)
Code=1, DIP6=off
(Slave 2)
Code=1, DIP6=on
(Slave 3)
BUS(IM) BUS(DS)
CDV-PC6
AC~
100~240VAC
Code=1, DIP6=off
(Slave 1)
5.3: Basic IN-OUT Wiring in Standard Mode
•The door station is compatible with other
monitors within the 2Easy range.
•For the last monitor connected to the
system, DIP6 should be set to ON.
1
4 5 6
8 9
0 #
7
2 3
*

The installer’s choice
CDV-DBC4A1
A B C D
CDV-RLC CDV-DBC4A1
Impedance
OFF ON
switch
BUS(IM) BUS(DS)
ID=0
CDV-PC6
AC~
100~240VAC
CDV-BDU
Optional functional modules:
Code=0 Slave 2 DIP6=on Code=0 Slave 3，DIP6=on
Code=0 Master，DIP6=on Code=0 Slave 1，DIP6=on
5.4: Star Topology Wiring With CDV-DBC4A1 in Standard Mode
CDV-BDU bus amplifier module
CDV-RLC staircase light controller module
CDV-DBC4 2/4 inputs branch distributor
•The system can be extended by up to 3 slave monitors for each monitor. It is
recommended to use a distributor CDV-DBC4 for the extension.
1
4 5 6
8 9
0 #
7
2 3
*

The installer’s choice
LOCK
Jumper position
JP
L1 L2 LK+ LK-
Door Lock Controlled with Internal Power
LOCK
POWER
SUPPLY
Jumper position
JP
L1 L2 LK+ LK-
Door Lock Controlled with Dry Contact
5.5: Electric Lock Connection
3. The door lock is limited to 12V, and holding
current must be less than 250mA.
2. Strike type locksof Power-on-to-unlock (fail
secure) type should be used.
4. The Unlock Mode Parameter of the
Monitor must be set to 0(default).
Note:
1. This mode only supports strike type locks.
1. An external power supply must be used
according to the lock power requirements.
2. The internal relay contact is restricted to AC
or DC Max 24V/1A.
• Power-on-to-unlock (Fail Secure) type:
Unlock Mode=0 (default)
• Power-off-to-unlock (fail safe) type:
Unlock Mode=1
Note:
3. Setup the Unlock Mode of Monitor for different
lock types.

The installer’s choice
(red)
ON
(blue)
ON
Beep+, Beep
(red)
ON
(blue)
ON
Beep+, Beep
(red)
ON
(blue)
OFF
Beep+
(red)
ON
(blue)
OFF
Beep
Inputting of code (ex.: 2011)
1~12 digits
Inputting of code (ex.: 2012)
1~12 digits
2011+#
Input the setting code.
(ex.:21)
Input the setting code.
(ex.:60)
20~59 60~99
2012+#
20+# 60+#
-
When the “ cancel” key is pressed, the LED lights off, the buzzer beeps, and the system exits the setting mode
- When there isn’t any operation in 10s, the LED lights off, the buzzer beeps, and the system exits the setting mode
(red)
OFF
(blue)
OFF
Beep, Beep+
*
Setting the code
for user group1
Setting the code
for user group2
13
5.6: Setting User Codes (PIN)
Setting a User Code for Lock 1(User Group1) and Lock 2(User Group 2) on the CDV
Enter programming mode by entering 1234#, 2 beeps will be heard.
(Master code 1234 can be changed if required - for more setting please refer to the CDV96KP manual)

The installer’s choice
LOCK
6.1: CDV91S Specifications
LOCK
● Input Voltage: 100~240Vac
● Input Frequency: 50~60HzRated
● Output Voltage: DC 28V+2VRated
●Power supply: DC 20~28V
●Power consumption: Standby 0.3W; Working 7W
●Monitor screen: 7 Inch digital color TFT
●Display Resolutions: 800*3(R, G, B) x 480 pixels
●Video signal: 1Vp-p, 75Ω, CCIR standard
●Wiring: 2 wires, non-polarity
●Dimension: 132(H)×226(W)×18(D)mm
6.2: CDV-PC6 Specifications
6.3: CDV-47DX Specifications
● Power Supply : DC 24V
● Power Consumption: Standby 14mA; Working status 122mA
● Camera: Color CMOS, 2.0 Mega pixel
1/2.7’’ fisheye camera,1700 wide angle
● Lock Power supply: 12Vdc, 250mA(Internal power)
● Output Current: 1.5A
● Working Temperature -10oC to +50oC
● Mounting: Surface mounting
● Working temperature: -15oC to +55oC
● Dimension: 182(H)×93(W)×44(D)mm
14
● Input Voltage: Max 230vac, 2A
● Dimension: 140(H) x 90(W) x 60(D)mm
6: Specifications:

The installer’s choice
The maximum distance of the wiring is limited in the 2Easy system. Using different
cables may also affect the maximum distance which the system can reach.
Basic IN-OUT Wiring Mode
Cable Usage A B
≤2 IM
B
≤16 IM
A
B
CDV-PC6
Belden 9470 UTP 2x0.75mm260 100 40
Belden 8471 UTP 2x1mm280 120 60
Cable and distance (unit:m)
7:System Wiring and Connections
1
4 5 6
8 9
0 #
7
2 3
*
15

The installer’s choice
B
A
C
2
2
CDV-DBC4A1
CDV-PC6
Cable Usage A B C
Belden 9740 UTP 2x0.75mm2 60 60 30
Belden 8471 UTP 2x1mm280 80 40
Cable and distance (unit:m)
Star Topology Wiring Mode With CDV-DBC4
1
4 5 6
8 9
0 #
7
2 3
*
16