CDVI CDV-91 User manual

2 -Wire Intercom System
USER MANUAL
Model: CDV-91

-1-
1.Parts and Functions
Rainy Cover
Camera Lens
Night View LED
Speaker
Nameplate
Call Button
Microphone
90 mm
176 mm
23 mm
2.Terminal Descriptions
BUS
PL
S1+ S2+ S-
1 2
ON
1 2
ON
MIC adjustment
Lock Control Jumper
Doorstation Code DIP
Main Connect Port
1 2 3
SPK adjustment

-2-
•Lock Control Jumper: To select the lock type: see 5.2.1 , 5.2.2
•Door Station Code DIP: Total 4 door stations can be supported,see 6.1
•Main Connect Port: To connect the bus line and the electronic locks.
•BUS: Connect to the bus line, no polarity.
•PL: External lock power input, connect to the power positive(power +).
•S1+, S2+: Lock power(+) output, to connect 2 locks.
•S-: Lock power(-) output, connect to the power(-) input of locks.
3.Specications
Power Supply : DC 24V (supplied by PS1-24V or PS5-24V)
Power Consumption: Standby 50mA; Working status 200mA
Camera: Pinhole Sharp Color CCD; 420 TV Lines
Unlocking time: 1-9S, set by monitor
Lock Power supply: 12Vdc, 300mA(Internal Power)
Temperature: -100C~+450C
Wiring: 2 wires (non-polarity)
Dimension: 176(H)×90(W)×24(D)mm
4.Mounting
4.1 Mounting Without Rainy Cover
160-165cm
1
2
1 2 3 4

-3-
4.2 Mounting With Rainy Cover
160-165cm
1
2
1 2 3 4
4.3 Placing Name Label
Move the plastic cover away to open the transparent name label cover, insert a name paper, then put
the plastic cover back to the panel.
name label
1 2
ON

-4-
4.4 Adjusting Camera Angle
5.1 Basic Connection
Use a screwdriver to loosen the screw and then adjust
the angle of the camera ,then x the screw.
5.System Wiring and Connections
-
+
AC~
monitor
DPS PS1
12
ON
L1 L2 PL S1+ S2+ S-

-5-
5.2 Electric Lock Connection
5.2.1 Door Lock Controlled with Internal Power
connect one lock connect two locks
Note:
1. Electronic lock of Power-on-to-unlock type should be used.
2. The door lock is limited to 12V, and holding current must be less than 250mA.
3. The door lock control is not timed from Exit Button(EB).
4. The Unlock Mode Parameter of Monitor must be set to 0 (by default).
EB
*
LOCK
BUS PL S1+ S2+ S-
LOCK
2nd
1ST
2nd
EB
*1ST
Jumper position in
Connect two locks
1-2
EB
*
LOCK
BUS PL S1
+
S2
+S-
Jumper position in
Connect one lock
1-2
5.2.2 Door Lock Controlled with Dry Contact
Note:
1. The external power supply must be used according to the lock.
2. The jumper must be taken off before connecting.
3. Setup the Unlock Mode of Monitor for different lock types.
•Power-on-to-unlock type:Unlock Mode=0 (by default)
•Power-off-to-unlock type:Unlock Mode=1

-6-
LOCK
BUS PL S1
+
S2
+S-
Take off the Jumper
POWER
SUPPLY
LOCK
BUS PL S1
+
S2
+S-
Take off the Jumper
POWER
SUPPLY
LOCK
connect one lock connect two locks
5.2.3 Unlock parameter setting(set on monitor)
1.Touch item on main
menu page.
2.Touch the screen anywhere
and hold for 2s.
3.Touch Installer setup item
4.A digital keypad and setting
instructions will be shown.
Manual
Monitor
Monitor
Memory
Playback
Album User Setup
09/30/2010 Thu.16:41
Close
Intercom Multimedia
About
?
H/W : --- a1.3
S/W: V17.11.418.00
Local addr: ---
Unlock timing: ---
Video standard: -
UI-CODE: ---
MCM-VER.: ---
Updated: ---
Home
Installer
setup
Caliber
TouchScreen
Code Number:[----]
[0010]#:Remove all remote control
[0011]#:Add remote control
[8000]#:Set as master unit 0
[8001]#:Set as slaver unit 1
[8002]#:Set as slaver unit 2
[8003]#:Set as slaver unit 3
[8004]#:Set as guard unit
[8005]#:Set as not guard unit
[8006]#:Panel on as slaver unit called
[8007]#:Panel off as slaver unit called
[8008]#:Date format:MM/DD/YYYY
[8009]#:Date format:DD/MM/YYYY
[8010]#:Set lock mode to 0
[8011]#:Set lock mode to 1
[8021]~[8029]
#Set the lock time of 1~9s
Multi language settings:
---
1
4
78
0
9
6
5
23
Cancel
Installation settings:
Note:
1.must connect the system correctly before setting.
2.the parameter will be saved in door station automatically,so you need only set on one monitor.
3.the above diagram is t for icon menu series monitors only, to text menu series monitors,please
refer to the corresponding user manual.

-7-
5.3 Multi Door Stations Connection
85~260VAC
DPS PS5
monitors
12
ON
L1 L2 PL S1+ S2+ S-
12
ON
L1 L2 PL S1+ S2+ S-
12
ON
L1 L2 PL S1+ S2+ S-
12
ON
L1 L2 PL S1+ S2+ S-
1 2
ON
1 2
ON
1 2
ON
1 2
ON
1# Camera
DIP=on,off,off
ID=00
ID=10
ID=01ID=11
2# Camera3# Camera4# Camera
DBC4
A B C D
OFF
ON
Impedance
switch
5.4.1 Basic IN-OUT Wiring Mode
5.4 Multi Monitors Connection
monitor monitor monitor monitor
Code=0, DIP-6=off
1 2 3 4 5 6
ON
Code=1, DIP-6=off
1 2 3 4 5 6
ON
1 2
ON
ID=00
85~260AC
PS5
DPS
Code=14, DIP-6=off
1 2 3 4 5 6
ON
Code=15, DIP-6=on
1 2 3 4 5 6
ON

-8-
5.4.2 With DBC4 Wiring Mode
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
Code=3, DIP-6=on
Code=1, DIP-6=on
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
Code=2, DIP-6=on
Code=0, DIP-6=on
OFF ON
OFF ON
monitor
monitor
monitor
monitor
monitor
monitor
monitor
monitor
85~260AC
DPS PS5
ID=00
1 2
ON
DBC4
A B C D
DBC4
A B C D
Impedance
switch
Impedance
switch
DIP=on,off,off
DIP=on,off,off
Code=15, DIP-6=on
Code=13, DIP-6=on
Code=14, DIP-6=on
Code=12, DIP-6=on
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON

-9-
6.Setup
6.2 DIP Switches Settings of Monitor
6.1 DIP Switches Settings of Door Station
Total 2 bits on the DIP switches can be congured.The switches can be modied either before or after
installation.
Bit state Descriptions
Default setting, ID = 0(00), set to the rst Door Station.
ID = 1(10), set to the second Door Station.
ID = 2(01), set to the third Door Station.
ID = 3(11), set to the fourth Door Station.
12
ON
1 2
ON
1 2
ON
1 2
ON
There are 6 bit switches in total. The DIP switches are used to congure the User Code for each Moni-
tor.
ON(1)
=
OFF(0)
=
ON
ON
Bit-6 is used to set video impedance,it should be set to ON if the Monitor is in the end of the line(bus),
otherwise set to OFF.
Bit state Setting Bit state Setting
The monitor is
not at the end
of the bus.
The monitor
is at the end
of the bus.
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON

-10-
Bit-1 to Bit-5 are used to User Code setting.The CDV-91 responds to 0~15 .
6.3 Notices
Name Description Usage
CDV-PS5 Power supply,85~260Vac input,24Vdc/3A
output,10 DIN modules
Connect with multi door stations or
multi monitors(up to 2 or above)
CDV-PS1 Power supply,85~260Vac input,24Vdc/1A
output,for basic kit only,4 DIN modules
Connect with one door station and one
monitor(depend on models)
Bit state User Code Bit state User Code Bit state User Code
Code=0 Code=6 Code=11
Code=1 Code=7 Code=12
Code=2 Code=8 Code=13
Code=3 Code=9 Code=14
Code=4 Code=10 Code=15
Code=5
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON

-11-
7.Cables Requirements
The maximum distance of the wiring is limited in the DT system. Using different cables may also affect the maxi-
mum distance which the system can reach.
When Monitor quantity < 20
Cable Usage A B C
Twisted cable 2x0.75 mm260 60 30
Twisted cable 2x1 mm280 80 40
When Monitor quantity > 20
Cable Usage A B C
Twisted cable 2x1 mm270 30 20
Twisted cable 2x1.5 mm270 50 30
The farest monitor
B
A
C
DPS PS5
DBC4
monitor
monitor
monitor
with two or four monitors
Note:If the monitor has been specied the distance,refer to the
parameter.

The design and specications can be changed without notice to the user. Right to
interpret and copyright of this manual are preserved.
Model: CDV-91