Civco GUS G14T-3-EU User manual



Copyright©2019AllRightsReserved.
GUS
®
isaregisteredtrademarkofCIVCOMedicalSolutions.
Allothertrademarksarepropertyoftheirrespectiveowners.
PrintedintheUSA.
Disinfection Soak Stations
ForTransesophageal(TOE)
UltrasoundProbes
REF:
G14TC-3-EU
G14T-3-EU
Operator’sManual
CIVCOMedicalSolutions
102FirstStreetSouth
Kalona,IA52247USA
Tel: 1‐800‐445‐6741
Fax: 1‐877‐329‐2482
Website:WWW.CIVCO.COM

GUSDisinfectionSoakStation™
50055_G 1 G14TC‐3‐EU/G14T‐3‐EU
Contents
PrincipleofOperation.........................................................................................................................................................2
SafetyPrecautions..............................................................................................................................................................3
SettingupyourGUS............................................................................................................................................................4
UponDelivery.....................................................................................................................................................................................4
GUSComponents................................................................................................................................................................................4
Installation:G14T‐3‐EU......................................................................................................................................................................5
Installation:G14TC‐3‐EU....................................................................................................................................................................6
EstablishingSoakingLevelsinTubes‐ForALLUnits..........................................................................................................................8
ForG14T‐3‐EU–ONLY.........................................................................................................................................................................9
ForG14TC‐3‐EU–ONLY....................................................................................................................................................................... 9
FillingtheSoakandRinseTubes‐ForALLUnits...............................................................................................................................10
OperationPlacingtheTOEProbeintheGUSSystem‐ForALLUnits...............................................................................................11
PlacingtheTOEProbeintheGUSSystem‐ForG14TC‐3‐EU–ONLY................................................................................................11
PlacingtheTOEProbeintheGUSSystem‐ForALLUnits................................................................................................................12
RemovingandRinsingtheProbes‐ForALLUnits............................................................................................................................12
SystemMaintenance.........................................................................................................................................................13
RepairandModification...................................................................................................................................................................13
DisposingofUsedHigh‐LevelDisinfectants......................................................................................................................................13
ChangingtheFilters..........................................................................................................................................................................13
CleaningSystem...............................................................................................................................................................................14
LimitedWarranty..............................................................................................................................................................15
APPENDIXA:TROUBLESHOOTING....................................................................................................................................16
QuickTroubleShoot.........................................................................................................................................................................16
APPENDIXB:SITEREQUIREMENTS...................................................................................................................................17
EnvironmentalConditions...............................................................................................................................................................17
VentilationRequirements................................................................................................................................................................17
SupplyRatings.................................................................................................................................................................................17
APPENDIXC:GUSPRODUCTSPECIFICATIONS..................................................................................................................18
GUSProductSpecifications..............................................................................................................................................................18
APPENDIXC:GUSPRODUCTSPECIFICATIONS..................................................................................................................19
ULApproval.....................................................................................................................................................................................19
CEMarkApproval............................................................................................................................................................................19
ECRepresentative............................................................................................................................................................................19

GUSDisinfectionSoakStation™
50055_G
2 G14TC‐3‐EU/G14T‐3‐EU
PrincipleofOperation
TheGUSSystemallowsTOEProbestobeimmersedinahigh‐leveldisinfectantsolution.TheUltrasound
Probeissuspendedinthesoakingcontainer,preventingdamagetothesensitivetip.
Thesystemisdesignedtoremovefumesfrom:
 Glutaraldehyde,
 Ortho‐phthaldehyde(OPA),
 HydrogenPeroxide,
 PeraceticAcid.
Fortheuseofalternativehigh‐leveldisinfectants,pleasecontactyourlocalrepresentative.
Oneofthecontainersisusedforcleanrinsewater.ThisensuresthatwhentheTOEProbeisremovedfrom
theunitforthefinalrinse,nohigh‐leveldisinfectantwilldriporoff‐gas.
Theunit’sblowerandcarbon‐filtrationsystemremovesfumesfromhigh‐leveldisinfectantsolutions.
Blowersdrawthefumesthroughthecarbonfilterwheretheyareeffectivelyneutralizedandcleanairis
returnedtotheroom.Noductworkorexternalventingisrequired.TheG14TC‐3‐EUand
G14T‐ 3‐EUseries
haveoneblower.


Figure 2: G14TC-3-EU
Side (return)
Vent
Curved
Soak Tube
Rinse Tube
Padded Storage
Compartment
Grip Clip
Soak
Tube
Tube
Guide
Rinse
Tube
Side (return)
Vent
Figure 1: G14T-3-EU
Support
Bracket
Grip Clip
Curved Soak
Tube
Soak
Tube

GUSDisinfectionSoakStation™
50055_G
3 G14TC‐3‐EU/G14T‐3‐EU
SafetyPrecautions
SignalWord
Thefollowingsignalwordsareusedthroughoutthismanual:
WARNING: Indicatesapotentiallyhazardoussituationwhich,ifnotavoided,could
resultindeathorseriousinjury.
CAUTION Indicatesapotentiallyhazardoussituationwhich,ifnotavoided,may
resultinminorormoderateinjury.Itmayalsobeusedtoalertagainst
unsafepracticesorpotentialequipmentdamage.
NOTE:  Indicatesadditionalhelpfulinformation.
WarningSymbols:Themeaningsofthelabelsandsymbolsthatappearonthepackaging
and/orthesystemareasfollows:
Dangerouselectricalvoltage
ProtectiveGrounding
NOTE:  Donotusethesystemforanypurposeotherthanitsintendeduse.
TheGUSSystemisnotintendedforthestorageofprobes,moistureontheprobescan
promotegrowthofbacteria.
Disconnectthepowerbeforereplacingthefilterorwhenservicingtheunit.
RefertotheMSDSofthehigh‐leveldisinfectantthatyouareusingforadditionalsafety
precautions.
NEVERplacetheprobeintoadrytube.MakesurethatthetipofyourTOEprobeis
straightbeforeinserting.Useafluidmotionwheninsertingtheprobetopreventitfrom
stickinginthetube.

GUSDisinfectionSoakStation™
50055_G 4G14TC‐3‐EU/G14T‐3‐EU
SettingupyourGUS
UponDelivery
Matchallitemsinthepackagewiththoseonthelistofcomponentsgivenbelow.Inspecteachitemfor
damage.Ifanycomponentsaremissingordamaged,orifyouhaveanyquestions,donotusethesystem;
immediatelycontactyourlocalrepresentative.
GUSComponents
GUSItems G14TC‐3‐EU G14T‐3‐EU
Soak/Rinsetubes 3 3
Rubberstoppers 3 3
High‐LevelDisinfectantlabel 2 2
Rinselabel 1 1
Angledsupportbracket 1 N/A
Foampad 1 1
Bottomwallmounttubeguide 1 1
Acrylicfrontpanel1 N/A
Cleaningbrushfortubes 1 1
Hollowwallanchors 13 4
Teststripclip 1 1
Screwdriver&RedPen 1 1
Filterinstalledinunit 1 1

GUSDisinfectionSoakStation™
50055_G
5 G14TC‐3‐EU/G14T‐3‐EU
Installation:G14T‐3‐EU
CAUTION Theunitis35.7cmwideandneedsatleast5.1cmofspaceontherightsideand
10.2cmontheleftside.
1. Establishgenerallocationofsystem,ensuringanadequateamountofspaceonbothsides.
2. Measureupfromthefloor156.2cm.Usingalevel,drawalineapproximately35.6cmlong.
3. Placetwomarksonthisline,27.9cmapart.
4. Forsheetrockwalls,usingaPhilipsdrillbit,drillthroughthesepencilmarksandtapinthehollowwall
anchorssuppliedwiththeunit.Tightenthescrewsfirmlytolockintheanchors.(Formasonrywalls
youwillneedtouseasuitableleadorplasticshieldwithbolt.Thesearenotsuppliedwiththeunit).
5. Slightlybackthescrewsoutofthewallanchors.
6. Lifttheunitintoplaceoverthescrewsandretighten.
7. Toinstallthelowerbracketmeasureup30.5cmfromthefloor,centerthebracketundertheunitand
markthescrewholeswithapencil.Installusingthewallanchorsandscrewsprovided.
8. PositionthesoakandrinsetubesintoplaceandaffixtheCIVCOlabelsasappropriate,asshowninthe
picture.
Figure 3. Hole locations for wall mount system

GUSDisinfectionSoakStation™
50055_G
6 G14TC‐3‐EU/G14T‐3‐EU

Installation:G14TC‐3‐EU
CAUTION Theunitis35.7cmwideandneedsatleast10.2cmonbothsides.
1. Establishgenerallocationofsystemensuring10.2cmofspaceonbothsides.
2. SeeDiagrambelowforanchorboltwholelocations.Marktheseonthewall.
3. Forsheetrockwalls,useaPhillipsscrewdrivertopressthetipofthewallanchorthroughthese
pencilmarksandscrewintothewalluntiltheanchorisflushwithwall.(Formasonrywallsyouwill
needtouseasuitableleadorplasticshieldwithbolt.Thesearenotsuppliedwiththeunit).Please
reviewthewallmountdiagrambelow.
Figure 4. Hole locations for wall mount system

GUSDisinfectionSoakStation™
50055_G
7 G14TC‐3‐EU/G14T‐3‐EU
4. Installlowertubecagefirst.SeeFigure5.
5. Notethatthelowersafetycagehassevenmountingholes.
6. Markholepatternonthewallusingdiagramonpreviouspage.Insertanchorsatthe19.7cm
marksfromthefloor.Insertscrewsintoanchors,leavingapproximately4cmshowing.
7. Placethecageagainstthewalloverthetwoscrewsandmarkpositionoftheremainingfivescrew
holes.
8. Removelowercageandinstalltheremainingfiveanchorsatthemarkedpoints.
9. Installscrewsinanchorsandplacecageoverscrewsandtighten.
10. Installthesupportbracket.SeeFigure6.Loosenthescrews,slidethebracketoverthescrewsand
tighten.
11. Removethescrewsfromthetoptwoanchors.
Figure 5: Safety Cage Figure 6: Support Bracket
Figure 7: Install System Figure 8: Location of Locking Machine Screw

GUSDisinfectionSoakStation™
50055_G
8 G14TC‐3‐EU/G14T‐3‐EU
12. Removethetwolockingmachinescrewslocatedunderthefrontcornersofthesystem.See
locationinFigure7.Placethesystemoverthesupportbracketandre‐installthetwolocking
machinescrews.SeeFigure8
13. Re‐installthetwotopscrewsintotheanchors.
14. Placethecurvedsoakandrinsetubeswithrubberstoppersintotherackandslidetheblueplastic
panelintothefrontofthesystem.SeeFigure9.Affixthesuppliedlabelsasappropriateasshown
inthepicture.
EstablishingSoakingLevelsinTubes‐ForALLUnits
NOTE: Priortopouringanyliquidintothetubes,fillwithwaterandletsitovernighttotestforany
leakagethatmayhaveoccurredduetodamageduringshipping.Ifleakisfound,donotuse
system.Contactyourlocaldistributor.Failuretodosowillaffectthewarrantyonthetube.
TOEprobeswilldisplaceliquidfromthetube.Aspartoftheset‐up,establishtheliquidlevelin
thetubeswithamarker,tapeorinkandplaceonthetube.
NEVERplacetheprobeintoadrytube.MakesurethatthetipofyourTOEprobeisstraight
beforeinserting.Useafluidmotionwheninsertingtheprobetopreventitfromstickinginthe
tube.
Figure 9: G14TC-3 Installed
Soak Tube
Soak Tube
Rinse Tube
Blue Plastic
Panel

GUSDisinfectionSoakStation™
50055_G
9 G14TC‐3‐EU/G14T‐3‐EU
Figure 10: Establishing Maximum Fill
ForG14T‐3‐EU–ONLY
1. Pourwaterintothetubeleaving7.6cmfromthetopofthetube.Donotusedisinfectantduringthe
set‐upprocess.
2. SlowlyinsertyourTOEprobeintothetube,watchthewaterlevel.DONOTallowthestrainreliefof
theTOEprobetobesubmerged.
3. Withtheprobefullyinserted,thewaterlevelshouldbemid‐waybetweenthe100cmmarkofthe
probeandthestartofthestrainrelief.Addorsubtractwaterasneededtoachievethislevel.
4. RemovetheTOEProbeandmarkthelevelofthewaterusingatapeorpermanentmarker.This
markisthemaximumfilllevelforthetubewithouttheprobe.Duringnormaloperation,youwill
losesomedisinfectanttoevaporation,youwillneedto‘topup’thedisinfectanttothislevel.
5. Theprobeshouldbefullyinsertedsothatthehandlerestsonthetopofthetube.Placethe
electricalconnectorintothetoppaddedcompartment.
6. Repeatthisprocessforadditionalprobesfromdifferentmanufacturers.
ForG14TC‐3‐EU–ONLY
1. Pourwaterintoonetube;filljustabovethegreyplasticfitting.
2. InsertyourTOEprobeintothetube.
NOTE:
 NEVERplacetheprobeintoadrytube.MakesurethatthetipofyourTOEprobeis
straightbeforeinserting.Useafluidmotionwheninsertingtheprobetopreventit
fromstickinginthetube.
3. Insertprobesothatthehandlerestsonthetopofthetube.Placetheelectricalconnectorintothe
toppaddedcompartment.Withtheprobefullyinserted,thewaterlevelshouldbemid‐way
betweenthe100cmmarkandtheendofthestrainrelief.Addorsubtractwaterasneededto
achievethislevel.SeeFigure10.

Strain Relief
100cm Mark
Water Level

GUSDisinfectionSoakStation™
50055_G
10 G14TC‐3‐EU/G14T‐3‐EU
4. Removetheprobedrawingitthroughadrypapertoweltopreventdrips.Thewaterlevelwiththe
proberemovedistheMAXIMUMFILLLEVELforthetube.Usinganindeliblepen,markthiswater
levelonalltubes.Itisimportantnottofillabovethismark.
5. Marktheothertube/tubesatthesamelevel.
6. Discardwaterfromthetube.
FillingtheSoakandRinseTubes‐ForALLUnits
CAUTIONMakesuretoturnthesystemONbeforepouringhigh‐leveldisinfectantinto
thesoakingtube.
Leavethesystemrunningwheneveritcontainshigh‐leveldisinfectant.
Keepthehigh‐leveldisinfectantsoakingtubecoveredasoftenaspossible,to
minimizeevaporationofthedisinfectant.Pleasenotethatthecoverisnot
intendedtobeatight‐fittingcover.
Changetheinitialrinsewateratleastonceperdayoraccordingtoyour
normalinfectioncontrolpractices.
1. Turnonthepowerswitch.Confirmthatthelightinthepowerswitchontheoutsideisilluminated.
2. Activate(ifrequired)andslowlypourthehigh‐leveldisinfectantintothesoakingtube.Thisshouldbe
donewiththetubeintheracksothatanyfumesarecarriedtothefilter.Fillthetubeuntilitreaches
theMAXIMUMFILLLEVELestablished.SeeFigure10.
3. Whentestingtheefficacyofyourdisinfectant,attachateststriptotheteststripclipprovidedwith
yourstation.Slowlylowertheteststripintothedisinfectant.Followteststripmanufacturer’s
InstructionsforUse.

GUSDisinfectionSoakStation™
50055_G
11 G14TC‐3‐EU/G14T‐3‐EU
OperationPlacingtheTOEProbeintheGUSSystem‐ForALLUnits
CAUTION Allprobesmustbemanuallypre‐cleaned,testedforleakage(ifapplicable),
anddriedpriortobeingplacedintheGUS

system.Consulttheprobe
manufacturer’sinstructionsfortheproperprocedures.Wearappropriate
personalprotectiveequipmentwhenworkingwithdisinfectantsolution.
Makesurethatthetipofyourprobeisstraightbeforeinsertingintothe
tube.
1. Confirmthatthesystemisswitchedonandthatthefanisrunning.
2. Removetherubberstopperfromthesoaktubeand,usingafluidmotion,inserttheprobeintothesoak
tube.
CAUTION Ensurethattheendoftheprobeisinastraightposition.
DONOTforcetheprobeintothetube.
PlacingtheTOEProbeintheGUSSystem‐ForG14TC‐3‐EU–ONLY.
NOTE: ItisIMPORTANTthatyoumakesuretheprobeisinsertedcorrectlyintothetubeasshown
inFigure9(whiteline).
Ifitisnotstraight,intheG14TC‐3‐EUtheprobecanbecomestuckintheT‐junctionand
possiblydamaged.
Figure11
Intheeventtheprobebecomesstuck,DONOTforcetheprobeout.
IfyouhavedifficultygettingyourTOEprobeinsertedcorrectlyintothetube,pleasecallyour
CIVCOMedicalSolutionsdistributorimmediatelyforreplacementtubes.
TOE probe should
NEVER go into this
section of the tube .
‘ T’ junction

50055_G
12 G14TC‐3‐EU/G14T‐3‐EU
GUSDisinfectionSoakStation™
Placing the TOE Probe in the GUS System - For ALL Units
1. Thehandleoftheprobeshouldnowrestontopofthesoaktube.Placetheelectricalconnectorinto
thetopcompartment.Youmaywishtousethecushionedspringcliptokeeptheelectricalcordoutof
theway.
2. SoaktheTOEprobeforthetimerecommendedbythedisinfectantmanufacturer.
RemovingandRinsingtheProbes‐ForALLUnits
CAUTION TypicallyasterilerinseisnotrequiredforTOEprobes;however,referto
yourprobemanualforspecificinstructions.
1. Grippingtheprobefirmly,drawitthroughthetowelorclothuntilyoureachtheflexibleendpartof
theprobe.
2. Transferthetipoftheprobeovertotheinitialrinsetubeandinserttheprobeuptothehandle.
Useacontinuousmotionwheninsertingtheinitialprobeintotherinsetube.Peelofftheglove,
trappingtheclothinside,anddiscard.
3. TheinitialrinseisdoneinthemiddlerinsetubeinsidetheGUSunit.Thisisanimportantstepto
preventdripsandoff‐gassingwhenmovingtheprobetothesink.
4. Removetheprobefromtheinitialrinsetubebydrawingitthroughadamppapertowelorsterile
cloth.Followyourprobe’sinstructionmanualforfinalrinsingandstorageprocedures.

GUSDisinfectionSoakStation™
50055_G
13 G14TC‐3‐EU/G14T‐3‐EU
SystemMaintenance
RepairandModification
Donotmodifyorrepairtheunitwithoutreviewingwithyourlocalrepresentative;contactyourlocal
representativetopurchasereplacementfiltersandparts.
Beforeattemptingtoperformroutinemaintenanceontheunit,thoroughlyreviewandunderstandthis
manualforcompletefamiliarizationwiththeunitanditsoperation.See‘Cleaning’section.
DisposingofUsedHigh‐LevelDisinfectants
NOTE: Insomeareas,itisillegaltodisposeofuseddisinfectantswithoutfirstdeactivating.
ALWAYSfollowthemanufacturer’s
 recommendationforthedisposalofhigh‐level
disinfectants.
CIVCOMedicalSolutionsmanufacturesGlute‐Out
®
,aglycine‐basedneutralizer(part#610‐1099)which
comesinaconvenientsingle‐usebottle.Glute‐Out

isspecificallyforusewithglutaraldehydeandOPA
baseddisinfectantsandprotectstheuserfromexposuretosplashesandspills.CIVCOMedicalSolutions
alsomanufacturesOxidOut
®,
asodium‐carbonate‐basedneutralizer(part#610‐2204)whichcomesina
convenientsingle‐usebottle.OxidOutisspecificallyforusewithhydrogen‐peroxidebaseddisinfectants.
Contactyourlocalrepresentativetopurchaseneutralizer.
ChangingtheFilters
GUS

hasapatentedfilterthat,innormaleverydayusewillhaveasix‐monthlife.Pleasecallyourlocal
representativetosetupanappropriatechangeschedule.Filtersmustbechangedatleastonceayear.
CAUTION Putrubberstopperonthecontainercontainingyourdisinfectant.Turnthe
mainpowerOFFanddisconnectthepowercordfromtheelectricaloutlet
1. Removethefoampadfromthetopcompartment.
2. Removethetopplatelocatedinthetopcompartmentbyturningthecaptivescrewscounterclockwise.
3. Removetheoldfilterbyinsertingfingersintothefingerholesandpullingup.Filtermaybesnugbut
shouldslideupwithsteadypressure.
4. Useamoistenedsoftclothwithamilddetergentandwipedownthewholefrontofthemachine.Also,
wipeinsidethemachinebehindtheairintakepanel.Dryallsurfaces.

GUSDisinfectionSoakStation™
50055_G
14 G14TC‐3‐EU/G14T‐3‐EU
5. Replacewithanewfilter,makingsuretheairflowarrowsarepointingtotherearofthemachine.
6. Puttheusedfilterintoaplasticbaganddisposeofitwithothernon‐hazardouswaste.
7. Replacethetopplateandtightenthecaptivescrewsbyturningclockwise.Replacethefoampad,plug
unitbackin,andturnonthemachine.
CleaningSystem
 CAUTION  TurnthemainpowerOFFanddisconnectthepowercordfromtheelectrical
outlet.
Whencleaningthesystem,alwayswearappropriatepersonalprotective
equipment.Potentiallyinfectiousmaterialadheringtotheunitcouldposean
infectioncontrolrisk.
Donotusesolventstocleantheacrylicfrontpanelortubes.Doingsomaycause
equipmentdamage.
Donotwipesurfaceswithhardorabrasivematerials.Doingsowillscratchthe
surfaces
1. Tocleantheacrylictubesusethecleaningbrushprovidedwithyoursystemandamilddetergent.
Donotusesolvents
2. Tocleanmetalsurfaces,useaclean,lintfreeclothmoistenedwithamilddetergentsolutionand
water.Wipeoffanydripsaroundthetubesandbelowtheshelf.
3. Donotspraycleaningliquidsontheintakeareaofthemachineasthiswilldamagethefilter.
4. Makesurethattheunitiscompletelydrybeforeuse.

GUSDisinfectionSoakStation™
50055_G 15G14TC‐3‐EU/G14T‐3‐EU
LimitedWarranty
Pleasecompleteandreturntheattachedwarrantycardtoyourlocaldistributor.
CIVCOMedicalSolutionswarrantstheGUSDisinfectionSoakStationtobefreeofdefectsinmaterials and
workmanship under normal use,for a period of one yearfrom thedateof delivery. This warranty does
not include filters, acrylic, or disposal pump unless it can be determined that
 failureisduetodefectsin
materialorworkmanship.
Ifthesystemisnotworkingcorrectlyorisdefective,contactCIVCOMedicalSolutions,andwewillrepair

orreplacetheunitatouroptionduringthewarrantyperiod.
CIVCOMedicalSolutionsassumesnoliabilityforconsequentialdamagesofanykindasaresultofthe
 use
ormisuseofthesystembythepurchaser,thepurchaser’semployees,oranyothers.
THISWARRANTYISEXPRESSLYINLIEUOFALLOTHERWARRANTIES,GUARANTEES,OBLIGATIONSOR
OTHERLIABILITIESEXPRESSEDORIMPLIED,ANDTHEREARENOWARRANTIESWHICHEXTENDBEYOND
THEDESCRIPTIONONTHEFACEHEREOF.WARRANTIESOFMERCHANTABILITYANDOFFITNESSFORA
PARTICULARPURPOSEARISINGFROMACOURSEOFDEALINGORUSAGEARESPECIFICALLYEXCLUDED.
Thiswarrantydoesnotcoverconditionsanddamagesresultingfromanyofthefollowing:
 Improperinstallation,deliverywithinthefacility,ormaintenance.
 Any repair, modification, alteration or adjustment not authorized by the
manufacturer.
 Misuse,abuse,accidentsorunreasonableuse.
 Incorrectelectriccurrent,voltageorsupply.
 Failuretofollowproperproceduresforuseoutlinedinthismanual.
 Consequential or incidental damages sustained by any person as a result of any
breachofthiswarranty.

GUSDisinfectionSoakStation™
50055_G
16 G14TC‐3‐EU/G14T‐3‐EU
APPENDIXA:TROUBLESHOOTING
QuickTroubleShoot
IfyourGUS

isnotrunning,checkthefollowing:
1) Ensurethattheunitispluggedintoalivewalloutlet.
2) MakesuretheOn/Offswitch(locatedonleftside)ison.
3) Intheeventtheunitisstillnotworking,checkthefuses:
a) Thefusesarelocatedontheleftsideoftheunitinthepowerinletmodule.
b) UNPLUGUNITBEFOREREMOVINGFUSEDRAWER.
c) Squeezethetwotabsonthefusedrawerandpulloutwardtoremovethefuses.
d) Ifafilamentisdamaged,replaceitwithaCIVCOMedicalSolutionsapprovedTypeFSF5x20
mm1amp250VAC.
4) Iftheunitisstillnotworking,pleasecontactyourlocalrepresentative.
CAUTION Ifyoursoakcontainerortubeisleaking,donotuseanyhigh‐level
disinfectantinit.Callyourlocaldistributorimmediatelyfora
replacementcontainerortube.

GUSDisinfectionSoakStation™
50055_G 17G14TC‐3‐EU/G14T‐3‐EU
APPENDIXB:SITEREQUIREMENTS
EnvironmentalConditions
Forindooruseonly.
Altitudeupto2,000meters.
Temperaturerange:5Cto40C.
Mainsupplyvoltagefluctuationsnottoexceed+/‐10%ofthenominalvoltage.
InsulationovervoltagecategoryII.
Pollutiondegree2.
VentilationRequirements
Theremustbeaminimumof10.2cmclearancebeneaththeunittoallowfortheclearanceofthe
soak/rinsecontainersandadequateairflow.
SupplyRatings
G14Series: AC230/240V0.5A50/60Hz
Fuses: TwoTypeFSF5x20mm1amp250VAC

GUSDisinfectionSoakStation™
50055_G 18G14TC‐3‐EU/G14T‐3‐EU
APPENDIXC:GUSPRODUCTSPECIFICATIONS
GUSProductSpecifications
Model G14TC‐3‐EU G14T‐3‐EU
FaceVelocity(MPM) 18.2 18.2
Electrical(230V50/60Hz) 0.5A 0.5A
Weight(tubesempty)19.5kg 15.9kg
Space&WeightRequirements:
Width 35.7cm 35.7cm
Depth 40.7cm 32.4cm
Height 165cm 165cm
Add10.2cmallowanceforairflowonbothsides.

GUSDisinfectionSoakStation™
50055_G
19 G14TC‐3‐EU/G14T‐3‐EU
APPENDIXC:GUSPRODUCTSPECIFICATIONS
ULApproval
USAandCanadianStandardsApproved.
CEMarkApproval
CBTestCertificatereferenceE178331‐A2‐CB‐1.
EN61010‐1:2010:Safetyrequirementsforelectricalequipmentformeasurement,control,andlaboratoryuse—
Part1:Generalrequirements.
ElectricalEquipmentDesignedforUsewithinCertainVoltageLimitsDirective2006/95/EC.
ElectromagneticCompatibilityDirective2004/108/EC.
ECRepresentative
HWFisher&Company
AreHouse11‐15
WilliamRoad
London
NW13ER
Tel:
+
44 (0)207 380 4963.