Civco 610-1238 User manual

TEE PROBE DISINFECTION AND
STORAGE SYSTEM
REFERENCE GUIDE

TEE Probe Disinfection and Storage System English
1
WARNING
nTo prevent electrical or wall damage, it is recommended the transducer storage rack be
installed by the facilities department.
nBefore attaching, you should have a phillips screwdriver and level.
nTo prevent cross-contamination of transducers, only store clean, disinfected transducers in
storage container or ensure holder is cleaned after each use.
nContainer has been tested for material compatibility for use with Cidex®, MetriCide 28®and
Omnicide cold chemical disinfectants/sterilants. MetriCide 28 and Omnicide have not been
tested for efficacy. Follow manufacturer's instructions for use.
nDo not use Cidex 7®, Cidex Plus®or other non-compatible disinfectants. Prolonged exposure
to disinfectants may cause transducer damage. Refer to your transducer manufacturer's
instructions for recommended disinfectant and maximum exposure time.
nIf leaking develops, discontinue use and notify CIVCO immediately.
LIST OF COMPONENTS - WALL SUPPORT
Transducer Storage Rack (1)
E-Z Anchor Molly Bolts (3) Flat Washers, nylon, #10 (3) Phillips mounting screws
8/32 x 1/2 (3)
ASSEMBLY
1. Place transducer storage rack against wall and level.
2. Mark the location of the three mounting holes.
3. Secure E-Z anchor molly bolts to wall with phillips screwdriver.
4. Mount transducer storage rack to molly bolts using phillips screws and washers.

English TEE Probe Disinfection and Storage System
2
USING WALL SUPPORT
NOTE: nWall support is designed to store and disinfect ultrasound transducers only and
should be used with Disinfection and Storage Containers of the TEE Probe
Disinfection and Storage System.
nWall support has two 2" x 2 1/4" (5.08 x 5.72cm) openings in the center to hold
storage and disinfection containers. Two .80" x 2.62" (2.03 x 6.66cm) openings at
either end of wall support securely hold transducer connectors in place.
STORAGE AND DISINFECTION CONTAINERS
INSTALLING STORAGE AND DISINFECTION CONTAINERS
1. With collar of container up, place in one of two center openings in wall support.
2. Pull container forward until it rests against front face of wall support.
3. For disinfection container, place supplied cap on top of container.
USING DISINFECTION CONTAINER
NOTE: nDisinfection container is designed to disinfect ultrasound transducers only and should
be used with Wall Support of the TEE Probe Disinfection and Storage System.
1. Remove cap and store on shelf of Wall Support.
2. Using supplied funnel, pour disinfectant into container until it reaches 'fill' line. Capacity is 1.4
liters or 1.5 quarts.
3. Guide flexible shaft of transducer into container.
4. Rest control handle in opening of container.
5. Cable should be looped in front of container with transducer connector(s) resting in openings
to the right or left. (See Figure 2.)
6. After disinfection, remove transducer and place cap on top of container. Cap reduces
unpleasant fumes and the chance of coming in contact with disinfectant.

TEE Probe Disinfection and Storage System English
3
USING STORAGE CONTAINER
NOTE: nStorage container is designed to store ultrasound transducers only and should be used
with Wall Support of the Tee Probe Disinfection and Storage System.
nProper storage of your transducer prevents excessive coiling of flexible shaft and
articulating section and prevents transducer shaft or transducer cable from becoming
pinched or otherwise damaged. The articulating section should be kept straight and
control knobs kept in 'free wheeling' or 'nonratcheting' mode (if applicable).
1. Guide flexible shaft of transducer into container.
2. Rest control handle in opening of container.
3. Cable should be looped in front of container with transducer connector(s) resting in openings to
the right or left. (See Figure 2.)
CLEANING
1. Wash wall support, disinfection container and storage container with water and mild detergent.
Disinfection container should be cleaned every time disinfectant is changed. A cloth or soft
bristle brush is recommended to minimize surface scratches.

Notes
4

CORPO RATE HEADQUARTERS:
2301 Jones Blvd., Coralville, IA 52241
319.248.6757, 800.445.6741
Fax: [phone]
USA OFFI CE:
102 First Street South, Kalona, IA 52247-9589
319.248.6757, 800.445.6741
Fax: [phone]
COPYRIGHT © 2015 ALL RIGHTS RESERVED. CIVCO IS A REGISTERED TRADEMARK OF CIVCO MEDICALSOLUTIONS. ALL OTHER TRADEMARKS ARE PROPERTY OF THEIR RESPECTIVE
OWNERS. PRINTED IN USA. ALLPRODUCT S MAY NOT BE LICENSED IN ACCORDANCE WITH CANADIAN LAW.
WWW.CIVCO.COM
043-562D