Coalesse Denizen User manual

Page 1 of 6
939500348 Rev B
ALLEN
WRENCH
Denizen™Round and Oval Table Assembly
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2016 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.

1 2
3
Page 2 of 6
939500348 Rev B
1. Place table top (preassembled
with PVD lid and liner, if your table
has the PVD lid option) face down on
the floor (preferably on a carpeted
surface to protect from scratching).
2. Place column/base assembly
on underside of table, lining it up with
pre-drilled holes. On the oval
tables, it should be positioned so
the base lines up with the top.
3. Place four (4) screws spaced
evenly around the column and slowly
tighten to make sure that the column
is centered on the table top.
SCREW

4
6
5
SCREW
GLIDE
Page 3 of 6
939500348 Rev B
4. Once the four (4) screws are
tightened into place, screw in the
remaining eight (8).
5. Flip the table over so that it is
upright.
6. Adjust the leveling glides by
tipping the table and backing the
glides out of their holes until the
table is level.

P age 4 of 6
939500348 R ev B
1
3
2
P V D MO U NT I NG
B R A C K E T
A L L E N HE A D
S C R E W
N O T E : This view is looking up underneat the works urface. T he
P VD mounting bracket is still in place so there is no way you
can install the bracket from underneath the worksurface. T his
view is pres ented only for illustrative purposes .
PVD Installation
1. Open P V D (power/voice/data)
lid by pressing down on the lid so
that it pops open (touch latch).
2. Take P V D mounting bracket
and pass it through the hole in the
center of the table.
3. On the left and right of the
P VD lid, there should be four (4)
Allen head s crews mounted on
the unders ide of the table. The
keyhole slots on the P V D mounting
bracket should slide over
thes e.
4. With the P V D mounting
bracket in place, tighten all four
(4) Allen head screws with and
Allen wrench.

5a 5b
6a 6b 7
PVD UNIT
PVD LINER
TAB
TAB
POWER
CORDS
COLUMN
Page 5 of 6
939500348 Rev B
5. Remove insert in PVD liner by
pressing down on the edges closest to
the PVD mounting bracket (5a) and
twisting clockwise (5b) until tabs come
out the slot to the side (5a). Push
insert to the side of the PVD liner.
6. Take PVD unit and snap it into
the mounting bracket (6a). Make
sure it is centered in the bracket so
that it can snap in all the way. Make
sure the cord tucks into the slot in the
PVD liner as well (6b). Repeat steps
2 thru 6 for installation of second
PVD.
7. Route the power cords through
the hole in the bottom of the PVD liner
and through the column.

8a
9
8b
PVD LINER
WIRE ROUTING
TAB
TAB
POWER CORD
Page 6 of 6
939500348 Rev B
8. Once the PVD units are in
place, move the insert in the PVD
liner back into position so that the
tabs are in the slots. Press down
on the insert near the tabs (8a)
and rotate it counter-clockwise
(8b) so that they snap into the
detents on the side.
9. Tip the table on its side, and
pull the power cords through the
hole in the base and out through
one of the wire routing cutouts on
the side of the base.
CUTOUTS IN BASE