Coalesse emu Heaven Seating & Table Cushion User manual

Page 1 of 7
939500509 Rev C
POUF/SIDE TABLE
HEX DRIVE
™
If you have a problem, question, or request, call
your local dealer, or Coalesse at 1.800.627.6770
Or visit our website: www.coalesse.com
© 2019Coalesse
San Francisco, California U.S.A.
Printed in U.S.A.
Heaven Seating & Table Cushion
The emu logo is a registered trademark of EMU GROUP S.P.A.. ITALY.
ARM CHAIR
(SHOWN WITH SEAT CUSHION)
ARM CHAIR
(SHOWN WITH SEAT CUSHION
AND BACK CUSHION)
LOUNGE CHAIR
(SHOWN WITH SEAT CUSHION,
BACK CUSHION AND PILLOW)
NOTE: PILLOW OPTION ONLY
AVAILABLE ON LOUNGE.
LOW TABLE BASE ROUND TABLE BASE ROUND TABLE BASE
#2 PHILLIPS

2c
1b
BALL
BUTTON
1a
NOTE: Line up front
edge of the cushion
with the front edge of
the chair frame.
CHAIR
WEBBING
STRING 2c
2b
2b
SEAT CUSHION
2a
2b
2c
Page 2 of 7
939500509 Rev C
Installing the Seat Cushion
onto a Heaven Chair
1. For the five (5) balls located on the seat cushion,
press button on ball inward (1a) and slide ball off
string (1b).
2. Place seat cushion in the center of the chair
(2a). Slide string through chair webbing (2b). Place
ball back onto string and slide upward (2c) so it fits
snugly against chair webbing.

BALL
BUTTON
1a
1b
2
BACK CUSHION
SEAT CUSHION
Page 3 of 7
939500509 Rev C
Installing the Seat Cushion and
Back Cushion onto a Heaven Chair
1. For the five (5) balls located on the cushion,
press button on ball inward (1a) and slide ball off
string (1b).
2. Route four (4) seat cushion strings through four (4)
eyelets on the back cushion.

3d
3e
NOTE: Line up front
edge of the cushion
with the front edge of
the chair frame.
CHAIR
WEBBING
STRING 3e
3d
BACK CUSHION
SEAT CUSHION
3c
3e3d
Page 4 of 7
939500509 Rev C
3. Place seat cusion and
back cushion in the
center of the chair (3c).
Slide string through chair
webbing (3d). Place ball
back onto string and slide
upward (3e) so it fits
snugly against chair
webbing.

4b
4c
CHAIR WEBBING
STRING
4a
Page 5 of 7
939500509 Rev C
4. Slide string through chair
webbing (4a). Place ball back
onto string and slide upward
(4b) so it fits snugly against
chair webbing (4c).

BALL
UNDERSIDE OF CHAIR
BUTTON
1a
2a
1b
2b
2c
Page 6 of 7
939500509 Rev C
Installing a Pillow
NOTE: Pillow option only available on Lounge Chair.
1. For the two (2) balls located on the pillow, press
button on ball inward (1a) and slide ball off string (1b).
2. Route two (2) pillow strings through the rain slit of
chair cushion and then through the chair webbing (2a).
Place ball back onto string and slide upward (2b) so it
fits snugly against chair webbing (2c).
RAIN SLIT

Installing the Pouf
Cushion
Lower pouf base onto underside of
pouf cushion.
Secure pouf base to cushion using
three (3) screws. Screw must be inserted
through each bracket and into underside
of pouf cushion.
1.
2.
Page 7 of 7
939500509 Rev B
2
UNDERSIDE OF
POUF CUSHION
SCREW
SCREW
BRACKET
1
POUF BASE
GLIDE
Secure (4) glides to underside
of base.
3.

1
Installing the Pouf and
31-1/2” Glass Top
Secure (4) glides to underside
of base.
Flip base over.
1.
2.
POUF / 31-1/2” BASE
SCREW
UNDERSIDE OF
GLASS TOP
3
SCREW
BRACKET
Page 8 of 7
939500509 Rev C
GLIDE
Install (3-4) rubber washers onto
each bracket. Lower glass top onto
top side of base aligning the glass top
standoffs with the brackets.
3.
Secure glass top to base with (3-4)
metal washers and (3-4) screws.
2.
RUBBER WASHER
METAL WASHER
4
METAL WASHER
RUBBER WASHER
STANDOFF

Installing the 47-1/2”
Glass Top
Secure (6) glides to underside
of base (see Figure 1 on page 8).
Flip base over.
1.
2.
Page 9 of 7
939500509 Rev C
Secure (10) bumpers evenly
about 14-3/4”. Lower glass centered
onto base.
3.