Crosswater Arcade US-ARCV17 User manual

Installation Instructions
2"
1"
G1/2”
1-3/8"
9-1/4"
8-1/8"
Adjustable
wrench
Channel
locks
Plumbers’ putty
or caulking
Flat head
screwdriver
Cross head
screwdriver
Hexagonal
key
2-1/2"
1-1/4"
G1/2”
1-1/4"
13”
11-3/4"
Arcade Air Boost Rain Heads
US-ARCV17
US-ARCV60
Introduction
Installation notes
This shower head is suitable for use with all water systems up to a
maximum operating pressure of 72 psi, beyond which pressure-
reducing valves must be installed. The minimum water pressure
requirement is 3 psi.
The shower head has been fully inspected throughout the production
process and only leaves our factory after a 15-step QC process.
Carefully remove the shower head from the box and check that all
parts have been supplied.
Before beginning installation, please check for any damage that may
have occurred during transport. Note: Damage claims cannot be
made during or after installation.
Improper installation shall result in loss of warranty in case of damage
caused by impacts or rubbing against rough surfaces.
IMPORTANT: Please read these instructions carefully before
beginning and retain for future reference.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Dimensions
Tools required
The installation must comply with all plumbing codes including local
codes and be installed by a licensed plumbing contractor.
IMPORTANT! Before installing a new shower head it is essential that
the supply lines are thoroughly flushed in order to remove any
remaining debris, solder or other impurities. Failure to carry out
this simple procedure can cause problems or damage to the
function of the shower head.
Installing shut-off valves on incoming supply lines is recommended
for ease of maintenance.
Turn off the main water supply before connecting to any existing
pipe work or doing any maintenance.
WARNING! Please check for any hidden pipes and cables, electric
or otherwise before drilling holes in a wall or floor.
9” shower head
13” shower head

Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]
Issue date: 20112019
SHOWER HEAD
WASHER
FILTER
SHOWER ARM
SHOWER HEAD
WASHER
FILTER



ATTENTION: Check all new connections for leaks.
Turn on the main water supply, close all faucets except for the new
installed shower head and as the system refills, check for leaks.

Installation
Rinse away any traces of soap and gently dry with a clean, soft cloth after each use. Rinse completely with water and dry any overspray. This
will maintain the finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of white vinegar and water. Do not allow the solution to soak on the product. Simichrome
Polish® contains a protective film to enhance maintenance and is helpful in preventing water spot buildup. Follow instructions to ensure
optimum results.
Never use an abrasive material such as a brush or scouring pad to clean the surface. The use of abrasive cleaners, cleansers or disinfectants will
alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and glass cleaners to
remain on the surface. Prolonged contact will alter surface finishes and void the warranty.
We DO NOT recommend using any household cleaners as many can cause damage to the finish.
Please see the website for care instructions for specific finishes.
Cleaning Instructions
Parts list
Shut off the water heating system. Then, with the main water supply
turned off, open the lowest hot and cold faucets and allow to drain
until supply pipes are empty.
Insert the washer and the filter into the shower head, then connect it to
the shower arm as shown opposite.