Crosswater Palmero US-B3CCS User manual

Installation Instructions
21-5/8"
1-3/4"dia
13-3/4"
10-5/8"
5-5/8"
18-1/2"
Weight - 12lbs
Tape
measure
Safety
glasses
Set
square
Pencil Spirit
level
Silicone
sealant
Installation notes
The installation must comply with all plumbing codes including local
codes and be installed by a licensed plumbing contractor.
Store the basin in a safe place until beginning installation to avoid any
damage.
Assemble the basin on a mat to protect against damage to the basin
surface.
Avoid getting cement, grit, sand or masonry products on to the
surface.
Protect and cover the basin during the installation period to prevent
damage from occurring.
IMPORTANT: Turn off the main water supply before connecting to
any existing pipework or doing any maintenance.
Please check for any hidden pipes and cables, electric or otherwise,
before drilling holes in a wall or floor.
Dimensions
Introduction
This basin has been fully inspected throughout the production
process and only leaves our factory after a 15-stage QC process.
Carefully remove the basin from the box and check that all parts have
been supplied.
Before beginning installation of the basin, please check for any
damage that may have occurred during transport. Note: Damage
claims cannot be made during or after installation.
It is recommended to remove the protective packaging film after
installation of the basin. Improper installation shall result in loss of
warranty in case of damage caused by impacts or rubbing against
rough surfaces.
Prior to installing the basin prepare a connection of water inlet/outlet.
The installation procedure of the basin may differ from that described
in the installation instructions depending on where the the basin is to
be located.
IMPORTANT: Please read these instructions carefully before
beginning and retain for future reference.
It is recommended to use US-BSW0101 waste flow products with this
basin.
Palmero Basin
US-B3CCS
Tools required

Once installed and sealed, DO NOT
use or get wet for 24 hours.
2Installation
3Maintenance
lThis installation guide does not include details of the waste
connection. The final decision about installation of the waste
connection should be made by a licensed plumbing contractor.
lInstall the waste according to the installation instructions supplied
with the waste.
lPlace the basin in the desired position making sure the waste hole
is aligned.
lApply sealant to inside edge and place into position.
IMPORTANT: Do NOT overtighten the waste as this may cause
damage to the basin which is not covered under warranty.
We recommend using a torque wrench to tighten the waste by
using a torque force between 25Nm or 18.5 ft/lb and 50Nm or
36.8 ft/lb.
l Remove the basin carefully from the packaging leaving the protective film in place until after installation is complete.
l Lift and place the basin into position. Avoid dragging the basin over rough surfaces.
1 Installation
Clean the basin regularly with non-abrasive soap and warm water. Fully rinse after cleaning.
While Clearstone is highly stain resistant, it is recommended that water containing additives such as creams, oils or salts is always drained and
rinsed immediately after use.
Please note that hair dyes and color cosmetics (eg. mascara, lipstick, face powder) may leave a slight discoloration if not removed immediately.
If any strong chemicals come into contact with the basin, remove and rinse immediately.
Water temperature should not exceed 49˚C/120˚F.
To remove a fine scratch or a slight mark, use a 1500-grade sandpaper. Gently sand the area with water. For best results, limit sanding to the
smallest possible area around the scratch. Re-polish the surface afterwards using a neutral polishing compound or toothpaste. It may be
possible to polish very fine scratches away without using abrasive papers: scrub gently with a soft brush or plastic pad (not a metal scouring
pad) and a mildly abrasive cream cleaner. Afterwards scrub the whole area with plenty of clean water and re-polish as before.
If the scratch or mark is too deep and cannot be repaired using the above method, it is possible to purchase a repair kit US-CRK. In order to
remove the scratches, follow the instructions included with the kit.
Issue date: 
Warranty - This Crosswater London product is covered by a 5-year warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]