Crosswater MPRO US-PRO391 User manual

Installation Instructions
Tape
measure
Safety
glasses
Set
square
Pencil Spirit
level
Silicone
sealant
Tools required
Installation notes
The installation must comply with all plumbing codes including local
codes and be installed by a licensed plumbing contractor.
Store the basin in a safe place until installation begins to avoid any
damage.
The new basin must be unpacked and inspected before removing the
old fixture.
Assemble the basin on a mat to protect against damage to the basin
surface.
Avoid getting cement, grit, sand or masonry products on to the
surface.
Protect and cover the products during the installation period to
prevent damage from occurring.
IMPORTANT: Turn off the main water supply before connecting to
any existing pipe work or doing any maintenance.
WARNING! Please check for any hidden pipes and cables, electric
or otherwise before drilling holes in a wall or floor.
Dimensions
Introduction
This product has been fully inspected throughout the production
process and only leaves our factory after a 15-step QC process.
Carefully remove the basin from the box and check that all parts have
been supplied.
Before beginning installation of the basin please check for any
damage that may have occurred during transport. Note: Damage
claims cannot be made during or after installation.
Improper installation shall result in loss of warranty in case of damage
caused by impacts or rubbing against rough surfaces.
Prior to installing the basin prepare a connection of water inlet/outlet.
The customer may choose the type and location of the faucets,
installation instructions should be supplied by the faucet
manufacturer.
The installation procedure of the basin may differ from that described
in the installation instructions, depending on the installation site.
IMPORTANT: Please read these instructions carefully before
beginning and retain for future reference.
We do not accept responsibility for any problems that may occur
through incorrect installation.
RECOMMENDATIONS:
It is recommended to remove the protective packaging after
installation of the basin.
MPRO Furniture Basins
US-PRO391 39” 1 TAP HOLE
US-PRO390 39” 0 TAP HOLE
US-PRO393 39” 3 TAP HOLE
US-PRO481 48” 1 TAP HOLE
US-PRO480 48” 0 TAP HOLE
US-PRO483 48” 3 TAP HOLE
US-PRO39 US-PRO48

2Installation
lThis installation guide does not include details of waste
connection.Final decision about installation of waste connection
should be taken by a suitably qualified contractor.
lInstall the waste according to the installation instructions supplied
with the waste.
lPlace the basin in desired position making sure waste hole is
aligned.
lApply sealant to the inside edge and place into position.
WARNING: Do NOT overtighten the waste as this may cause
long-term damage to the basin.
We recommend to use a torque wrench to tighten the waste by
using a torque force between 25Nm or 18.5 ft/lb and 50Nm or
36.8 ft/lb.
IMPORTANT:
Crosswater London cannot accept responsibility for any
injuries caused to those attempting to install this basin
without adequate and appropriate tools or resources.
l Remove the basin carefully from the packaging.
l Do not drag the basin over rough surfaces or sharp objects.
Lift and place the basin into position.
lDo not drop the basin!
1Installation - carriage
3Maintenance
A simple routine of regular care will keep your vitreous china and fireclay products clean and fresh.
Rinse away any traces of soap and gently dry with a clean soft cloth after each use. A mild detergent, warm water and a soft cloth will remove
normal dirt and soap accumulations from surfaces.
Soft abrasive cleaners may be used on vitreous china and fireclay. Never use abrasive cleaners without water. Do not use caustic cleaners or
disinfectants as they can alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and glass cleaners to
remain on the surface. Prolonged contact can alter surface finishes and void the warranty.
Issue date: 19112020
Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]
IMPORTANT: Basins are designed for installation with MPRO
vanities.
Basins are not suitable for wall-hung installation without
underside support. It is the responsibility of the installer to
provide adequate support.
Crosswater London cannot be held responsible for inadequate
wall-hung installation.
Mounting hardware for wall-hung installation not supplied.