Crosswater Limit LI120WNC User manual

Designed to comply with BS EN 200 for single taps
/combination taps and BS EN 817 for single lever mixers, for
water systems of type 1 and 2 general technical specifications
and to be used within systems designed to BS 6700. BS 6700
recommends the temperature of stored water should never
exceed 65°C.
meet all normal requirements and will minimise the build up
of lime scale in hard water areas. If the fitting is installed at
low pressure (tank fed), then the minimum distance from the
highest installed position of the outlet to the underside of the
cold tank should be at least 2 metres to ensure adequate
performance.
V10423
LIMIT
IMPORTANT INFORMATION BEFORE YOU START
Please read carefully and keep this information for further reference.
2 Hole Basin Set Wall Mounted No Pop-Up Waste
i
1
PRODUCT CODES:
LI120WNC
LI120WNF
LI120WNM
All products manufactured and supplied by
Crosswater are safe provided they are installed, used
correctly and receive regular maintenance in accordance
with these instructions. If you are in any doubt about your
ability to install this product safely you must employ the
services of an experienced qualified plumber.These fittings
need to be installed in accordance with, and meet the
requirements of the Water Supply (Water Fittings)
Regulations 1999 and Scottish Byelaws 2004.
Operating pressure range: Minimum 0.2 bar, Maximum 5.0
bar. Maximum static pressure: 10.0 bar.
Note: Nominally equal (balanced) inlet supply pressures are
recommended for optimum performance with mixer taps.

2
IMPORTANT INFORMATION
Please read carefully and keep this information for further reference.
i
NOTE: ALL DIMENSIONS IN MILLIMETRES
DIMENSIONS
These taps and mixers should be installed in compliance with the Water Regulations.
Where the supplies are unbalanced, i.e. Hot water from cylinder tank / cold from the mains, approved check valves must be
fitted in the supply pipes.
For further details contact your Local Water Authority.
155
3
148
40
120
210
80
40
105
90~110
318.5
223
196
105
Remove all packaging and check the fitting for damage before starting installation.
Before starting any installation please consider the following: before drilling into walls, check that there are no
hidden electrical wires, cables or wate supply pipes. This can be checked with the aid of an electronic detector.
If power tools are used do not forget to: -
Wear eye protection
feeds is recommended for ease of maintenance.
Before installing the new fitting it is essential that you thoroughly flush through the pipework in order to remove any
remaining swarf, solder, etc. Failure to carry out this procedure could cause problems or damage to the workings of the fitting.
Take care when handling the ‘flexible connecting pipes’, do not bend, twist or crush them. Only tighten the pipes by hand. Do not
crush or kink the shower hose, this could damage the hose and cause leaks.
BEFORE YOU START
Important pre-Installation Notes

3
INSTALLATIONINSTALLATION
ATTENTION
Having first checked all new connections, turn on the mains stop cock, close all taps except the new mixer and as the
system starts to refill check for leaks. Once you have satisfied your selhat there are no leaks, switch on the water heating.
First shut o your water heating system then, with your mains stop cock closed, open the lowest hot and coldtaps in the
house and allow to run until the cold storage tank and pipes are empty (the hot water storage cylinderalways remains full).
Where combination boilers are fited it is only necessary to tur o the boiler and shut o the incoming mains.Fitting isolating
valves to the inlet feeds is recommended for ease of maintenance.
Remember to turn o the mains water supply before connecting to any existing pipe work.
Warning!
Please check for any hidden pipes and cables before drilling holes in the wall.
Valve Body
A recess must be made in the wall to accommodate the mixer body.
Place the mixer in position, check to see if any alterations are needed to the existing pipe work.
Secure the mixer body into the wall recess via the lugs on the body.
Connect the water supply to the tap with hot water on the le and cold on the right. (When viewed from the front)
Wall plate
Apply a narrow bead of clear silicone sealant around the back edge of the cover plates and carefully press intoposition.Spout
Push the spout and adjust to vertical alignment before tiahten the grub screw using the hexagonal key provided
ATTENTION
Having first checked all new connections, turn on the mains stop cock, close all taps except the new mixer and asthe system
starts to refill check for leaks.zOnce you have satisfied yourself that there are no leaks, switch on the water heating
BODY
SPOUT
SLEEVE
FLANGE
CARTRIDGE
RETAINING NUT
ALLEN KEY
HANDLE
COVER CUP

Part of the
Bathroom Brands Group
Rennie Drive, Dartford
Kent DA1 5FU
United Kingdom
0345 873 8840
4
CARE & MAINTENANCE
CLEANING THE CARTRIDGE
The concealed cartridge should give trouble free service, but in the event of any problems, servicing is straight forward.
To remove the cartridge:
CLEANING THE PRODUCT
The material we use in our taps is very durable, nevertheless care should be taken when cleaning them.
They should be cleaned only with warm soapy water followed by rinsing
with clean water and drying with a so cloth. All finishes are vulnerable to acid attack and some strong substances such
as household cleaners, disinfectants, denture cleaners, hair dyes, wine making, and photographic chemicals can cause
the surface to go black or peel.
Note: Never use abrasive detergents or disinfectants or those containing alcohol, hydrochloric acid or phosphoric acid.
With an hexagonal key loosen the screw, but do not remove it. Pull o the handle and unscrewthe cover. Using the correct
size spanner unscrew and removethe retaining nut. Pull out the cartridge taking note of itsorientation. Wash the cartridge
with clean running waterand make sure that any trapped debris has been removed.Dry and lightly grease the seal
(only use silicone grease) andreplace the cartridge followed by the nut, cover and handle.
BODY
SLEEVE
FLANGE
CARTRIDGE
RETAINING NUT
ALLEN KEY
HANDLE
COVER CUP