Crosswater Taos 17-14-T User manual

15121426-B
Teflon Tape
Adjustable Pliers
Adjustable Wrench
Tools You Will Need
Hacksaw
For ease of installation you will need:
●To read the installation instructions completely before beginning.
●To read all warnings, care, and maintenance information.
●To complete the valve rough-in prior to installing this trim kit.
Screwdriver
Taos Pressure-balance Tub and Shower Set Trim
17-14-T
Installation Instructions
Before beginning installation, check for any
damage that may have occurred during transport.
Note: Damage claims cannot be made during or
after installation.

Installation Instructions
1
15121426-B 2
Remove the mud guard. Install diverter sleeve, stem and
button on to the valve.
5
Install the appropriate diverter stem
and sleeve extensions supplied with
the trim to allow easy access to the
diverter button.
6
Install diverter stem and sleeve onto
the valve.
17-14-T
2
7
Measure and note the distance ‘YY’
(the distance between the bottom of
the handle assembly and the
escutcheon).
Carefully slide the escutcheon on
valve.
3
Carefully slide escutchen on valve.
If diverter knob is accessible, go to
step #13. If not continue to step #4.
Remove escutcheon and diverter
sleeve, stem and button.
a
b
8
a.) Add the threaded nipple and
pressure balance stem extensions.
b.) Attach handle assembly.
b
a
1/2＂3/4＂
1/2＂3/4＂
4
9

13
15121426-B3
10
Remove the handle and escutcheon
assembly, the plate, stem and nipple.
Place handle assembly on valve
and rotate clockwise to secure
escutcheon.
15
Remove the handle and escutcheon
assembly, the plate, stem and nipple.
If handle assembly will not secure
escutcheon to the wall, measure and
note the distance ‘XX’(the distance
between the bottom of the handle
assembly and the escutcheon)
Cut stem and nipple the amount
noted in step # 14. (Never cut the
stem and nipple while still on the
valve. This may damage the valve.)
16
Cut stem and nipple extensions the
amount noted in step # 9. (Never
cut the stem and nipple while still on
the valve. This may damage the
valve.)
Re‐install the nipple and stem
extensions. Then, go to step #19.
12
17
Re-install the trimmed stem and
nipple on the valve.
Place escutcheon on valve. Thread
on handle assembly to secure
escutcheon.
a
6
17-14-T-PC
17-14-T-SN
17-14-T-PN
17-14-T-BZ
15121426-B
Applicable Standards/Codes
Installation Dimensions
}
b
b
a
11
14
18
IAPMO certified to meet or exceed the following:
• ASME A112.18.1/CSA B125.1
• Uniform Plumbing Code
• National Plumbing Code of Canada
• EPA WaterSense
• ADA Compliant
2 9/16＂
3 11/16＂
4＂
2 3/16＂
7 5/16＂
2 3/16＂
2 3/4＂
1 1/2＂
7 5/8＂
7/16＂
7＂
3＂
7/8＂
2 3/16＂-3 3/16＂
10 3/8＂
9 3/16＂
1/2＂NPT
7/8＂-2 1/8＂
1/2＂
1/2＂NPT
1/2＂NPT
1/2＂NPT
7/8＂-1 7/8＂
5 1/2＂-5 7/8＂
(5‐3/16＂with extensions)

5
17-14-T-PC
17-14-T-SN
17-14-T-PN
17-14-T-BZ
15121426-B 4
22 3
Remove tub spout flow guide with key and flush out debris.
Reinstall flow guide and save key for homeowner.
Turn shower valve on and test the diverter.
Rinse away any traces of soap and gently dry with a clean, soft cloth after each use. Rinse completely with water and dry
any overspray. This will maintain the finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of white vinegar and water. Do not allow the solution to soak on the
product.
Simichrome Polish® contains a protective film to enhance maintenance and is helpful in preventing water spot buildup.
Follow instructions to ensure optimum results.
Never use an abrasive material such as a brush or scouring pad to clean the surface. The use of abrasive cleaners,
cleansers or disinfectants will alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and
glass cleaners to remain on the surface. Prolonged contact will alter surface finishes and void the warranty.
We DO NOT recommend using any household cleaners as many can cause damage to the finish.
Please see the website for care instructions for specific finishes.
Cleaning Instructions
15121426-B
Apply teflon tape to the shower arm
and thread clockwise into the nipple
and slide on the flange.
19
Replacement Parts
9Q1146
No. Description Part No.
1
Handle Assembly
Diverter Knob Sleeve2
Spout Assembly 9Q1192
3
4
5
6
7
8
Spout flow guide and key 9Q1110PL9
9Q1175NT
9Q1176NT
9Q1174
5L0C0871
5T1C0319NT
5P0C0582NT
Pressure Balance Stem Extension
Diverter Knob & Stem
Diverter Knob Sleeve Extensions
Diverter Knob Stem Extensions
Threaded Nipple Extension
21
Apply teflon tape to the tub spout
nipple and thread on wall tub spout.
20
Apply teflon tape to the end of the
shower arm and thread the
showerhead on to the shower arm.
Teflon Tape Teflon Tape
9/16”min
Teflon Tape
4
3
2
1
56
7
9
8

5
17-14-T
15121426-B 4
22 3
Remove tub spout flow guide with key and flush out debris.
Reinstall flow guide and save key for homeowner.
Turn shower valve on and test the diverter.
●Only use a soft, dampened sponge or cloth to clean and polish the fixture.
●Wipe fixtures and the immediate areas clean and rinse completely with water immediately after installation and after
applying any cleaner.
●If you are using a cleaning compound on or close to the product, please test the compound on a hidden area of the
trim to ensure it will not damage the finish.
●Do not allow cleaners to soak anywhere on the product.
Cleaning Instructions
15121426-B
Apply teflon tape to the shower arm
and thread clockwise into the nipple
and slide on the flange.
19
Replacement Parts
9Q1146
No. Description Part No.
1
Handle Assembly
Diverter Knob Sleeve2
Spout Assembly 9Q1192
3
4
5
6
7
8
Spout flow guide and key 9Q1110PL9
9Q1175NT
9Q1176NT
9Q1174
5L0C0871
5T1C0319NT
5P0C0582NT
Pressure Balance Stem Extension
Diverter Knob & Stem
Diverter Knob Sleeve Extensions
Diverter Knob Stem Extensions
Threaded Nipple Extension
21
Apply teflon tape to the tub spout
nipple and thread on wall tub spout.
20
Apply teflon tape to the end of the
shower arm and thread the
showerhead on to the shower arm.
Teflon Tape Teflon Tape
9/16”min
Teflon Tape
4
3
2
1
56
7
9
8

13
15121426-B3
10
Remove the handle and escutcheon
assembly, the plate, stem and nipple.
Place handle assembly on valve
and rotate clockwise to secure
escutcheon.
15
Remove the handle and escutcheon
assembly, the plate, stem and nipple.
If handle assembly will not secure
escutcheon to the wall, measure and
note the distance ‘XX’(the distance
between the bottom of the handle
assembly and the escutcheon)
Cut stem and nipple the amount
noted in step # 14. (Never cut the
stem and nipple while still on the
valve. This may damage the valve.)
16
Cut stem and nipple extensions the
amount noted in step # 9. (Never
cut the stem and nipple while still on
the valve. This may damage the
valve.)
Re‐install the nipple and stem
extensions. Then, go to step #19.
12
17
Re-install the trimmed stem and
nipple on the valve.
Place escutcheon on valve. Thread
on handle assembly to secure
escutcheon.
a
6
17-14-T
Applicable Standards/Codes
Installation Dimensions
}
b
b
a
11
14
18
IAPMO certified to meet or exceed the following:
• ASME A112.18.1/CSA B125.1
• Uniform Plumbing Code
• National Plumbing Code of Canada
• EPA WaterSense
• ADA Compliant
2-1/2"
3-3/4"
4＂
2-1/4"
2-1/4"
2-3/4＂
1-1/2＂
7-5/8＂
1/2"
7＂
3＂
7/8＂
2-1/4" - 3-1/4"
10-3/8＂
9-1/4"
1/2＂ NPT
7/8＂ - 2-1/8＂
1/2＂
1/2＂ NPT
1/2＂ NPT
1/2＂ NPT
7/8＂ - 1-7/8＂
5-1/2＂ - 5-7/8＂
(5‐3/16＂with extensions)
7-1/4"
Warranty - All Crosswater London products come with a limited lifetime warranty. For full details, terms and conditions visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]