Crosswater Lazo LA1416FC User manual

1 V10623
LAZO
IMPORTANT INFORMATION BEFORE YOU START
Please read carefully and keep this information for further reference.
Floor Standing Bath Shower Mixer
i
Operating pressure range: Minimum 0.2 bar, Maximum 5.0 bar.
Maximum static pressure: 10.0 bar.
Note: Nominally equal (balanced) inlet supply pressures are
All products manufactured and supplied by Crosswater are
safe provided they are installed, used correctly and receive
regular maintenance in accordance with these instructions. If
you are in any doubt about your ability to install this product
safely you must employ the services of an experienced
meet the requirements of the Water Supply (Water Fittings)
Regulations 1999 and Scottish Byelaws 2004.
recommended for optimum performance with mixer t
LA1416FC/F/M
aps.
Designed to comply with BS EN 200 for single taps /
combination taps and BS EN 817 for single lever mixers, for
and to be used within systems designed to BS 6700.
BS 6700 recommends the temperature of stored water should
never exceed 65°C.
meet all normal requirements and will minimise the build up
of lime scale in hard water areas.
minimum distance from the highest installed position of the
outlet to the underside of the cold tank should be at least 2
metres to ensure adequate performance.
PRODUCT CODES:
®

2
IMPORTANT INFORMATION
Please read carefully and keep this information for further reference.
i
NOTE: ALL DIMENSIONS IN MILLIMETRES
These taps and mixers should be installed in compliance with the Water Regulations.
Where the supplies are unbalanced, i.e. Hot water from cylinder tank / cold from the mains, approved check valves must be
DIMENSIONS
For further details contact your Local Water Authority.
®

3
®
BEFORE YOU START
Warning:Before starting any installation please consider the following: before drilling into walls, check that there are no hid-
den electrical wires, cables or wate supply pipes. This can be checked with the aid of an electronic detector.
feeds is recommended for ease of maintenance.
Warning:
not crush or kink the shower hose, this could damage the hose and cause leaks.
Important Pre-Installation Notes
If power tools are used do not forget to: -
Wear eye protection
Important:

4
COMPONENTS
HANDSET
SPOUT
CONNECTION
SCREW
DIVERTER
HANDLE
UPSTAND PIPE
PLASTIC COVER
DRAIN PLATE
FLOOR BOLTS
HOSE CONE
Shower Hose
®
SPIRIT LEVEL
DRAIN CONNECTION

5
INSTALLATION
12
3
The floor needs to be prepared by making a cavity at least
50mm indepth within a solid floor. Please note the floor tile
should be fixed to the MIN marking on the protective covers.
The MAX depth depends on the bathtub's height on site,
and ensure precise horizontal/vertical alignment with a
spirit level.
Once achieved secure in place with the floor bolts provided.
The fixing seat can be fixed in any orientation inside your
cavity as the
Mark 4 points on the ground where the fixing seat will be
installed and drill four ɕ8 sized screw holes.
final fix parts are fully adjustable.
4
# #*/)*'+$+ ..#*0' !'0.# *!'' -$. /
 !*- !$)'*)) /$*)$.( ǻ
).0- /# +'./$*1 -$.' !/$)+' until testing is
complete. This is a safety feature and will provide additional
protection while pressure testing for leaksto supplies or
valvebody is under taken.
Make correct connections to hot and cold as shown.
®
MINIMUM DEPTH
50
60
Minimun
depth in
the ground
ɶ150
HOT INLET COLD INLET
FLOOR BOLTS
HOT INLET COLD INLET
SPIRIT LEVEL
Ho'eǛmm

INSTALLATION
56
7
Proceed with the air &water tests of the valves and
connections.
Do not removed the screws, in case that the plastic plate
spurts out.
Once the testing is complete the plastic cover can be
removed. Four screws should be removed (Attention:
Remember to keep these 4 screws for step 10, so as to
use in the installation of the faucet body).
The #*/)*'pipes should be flushed of all debris
etc again 4.0$/ ' ' )"/#*!+'./$#*. *-+$+ 
before remov$)" the drain plate.
Notes: emove the drain connection when flushing the
debris from the pipes, otherwise the water will not come
out from the outlet of the drain plate.
8
Remove four screws and drain plate, these four screws will
not be used in subsequent installations.
2/+,Ȅ1%"*&+041"/02--)6"#,/" laying the floor
tiles.
The flooring can then be fitted to cover the void as shown
above. The diameter needs to be circa 100-115mm in order
to be covered by the decorative flange.
®
6
SCREW
PLASTIC
COVER
PLASTIC
HOSE
DRAIN CONNECTION
DRAIN PLATE
FIXING SEAT
SCREW
HOT INLET COLD INLET
HOT INLET COLD INLET
COLD INLET
HOT INLET
HOT INLET COLD INLET
HOSE POINT
DRAIN PLATE

INSTALLATION
510
11
On the main body of the product slide the cover plate up
the upstand taking care not to mark the chrome.
Next the core under the upstand pipe should be pushed
down into the corresponding holes of the fixing seat. This is
a pre-tested product so care should be taken not to put
undue stress on these tails as this could damage the seal
within the body of the tap itself.
Rotate the fixing flange to adjust the spout direction properly.
This fixing flange can be rotated 360°.
Finally the upstand can be tightened onto the fixing seat using
the grub screws (The four screws were removed from
the plastic cover in Step 5).
12
ATTENTION
Having first checked all new connections, turn on the
mains stop cock,close all taps except the new mixer and
as the system starts to refill check for leaks.
Once you have satisfied yourself that there are no leaks,
switch on the water heating.
7
®
9
COVER PLATE
CORE
FIXING SEAT
COVER PLATE
SCREW
FIXING
FLANGE
SPOUT
DIVERTER
HANDLE
UPSTAND PIPE
HANDSET
SHOWER
HOSE
SPOUT
CONNECTION
UPSTAND PIPE
COVER PLATE
Note: At this point the water can be switched on and the
unit tested for leaks. Extra care and time should be
taken examining the base of this as it will be concealed.
once the installation is complete. Finally the handset,
spout and hose can now be connected to the unit.
HOSE
CONE
HOSE NUT
HOT INLET COLD INLET
UPSTAND
PIPE
FIXING
SEAT
HOT INLET
COLD INLET
SCREW
HANDLE

8
Part of the
Bathroom Brands Group
Lake View House
Rennie Drive, Dartford
Kent DA1 5FU
United Kingdom
0345 873 8840
www.crosswater.co.uk
Before use:Unscrew the aerator and allow the water to run the
freely until all debris is removed. Screw the aerator back into
the spout once all impurities have been flushed from the
water supply.
Periodically: Using the key provided in the box, unscrew the
aerator from the spout and rinse with clean running water.
Once all loose debris and dirt has been cleared, replace the
aerator into the spout and tighten with the key provided
CLEANING THE AERATOR
CARE & MAINTENANCE
CLEANING THE CARTRIDGE
The concealed cartridge should give trouble free service, but
in the event of any problems, servicing is straight forward.
To remove the cartridge:
Turn on the lever and using allen key loosen the grub screw
&+%+!)"21!,+,1/"*,3"&1ѷ2)),Ȅ1%"%+!)"+!
unscrew the cover. Using the correct size spanner unscrew
and remove the retaining nut. Pull out the cartridge taking
note of its orientation. Wash the cartridge with clean
running water and make sure that any trapped debris has
been removed.
Dry and lightly grease the seal (only use silicone grease)
and replace the cartridge followed by the nut, cover and
CLEANING THE PRODUCT
The material we use in our taps is very durable, nevertheless
care should be taken when cleaning them. They should be
cleaned only with warm soapy water followed by rinsing
vulnerable to acid attack and some strong substances such
as household cleaners, disinfectants, denture cleaners, hair
dyes, wine making, and photographic chemicals can cause
the surface to go black or peel.
Note: Never use abrasive detergents or disinfectants or those
containing alcohol, hydrochloric acid or phosphoric acid.
®
1
2
SPOUT
DIVERTER
RETAINING NUT
CARTRIDGE
COVER
HANDLE