Crosswater ISLSC1200 User manual

INFINITY SLIDER SINGLE DOOR
INSTALLATION INSTRUCTIONS
ISLSC1200
ISLSC1400
ISLSC1700
A

IMPORTANT - Please read before installation
Please read these instructions carefully before starting
installation and keep in a safe place for future reference.
Check the contents of the pack carefully before installation.
Simpsons will not be held responsible for any de-fit / re-fit costs
where faulty product has been fitted.
If any fault is found with materials or workmanship, it must be
reported immediately to the manufacturer. Remedial action will
be taken, based on information received, on condition that:
1. Full details are supplied to the manufacturer;
2. The enclosure has not been modified or tampered with;
3. The manufacturer is informed of any damage/shortages
prior to installation.
We do not accept responsibility for any problems that may occur
through incorrect installation.
The success of the installation and operation of any shower
enclosure is, of course, dependant on the squareness, alignment
and construction of the walls to which fixing is to be carried out.
VERY IMPORTANT
You must complete all tiling and grouting, and the shower tray
MUST be level and fully sealed to the tiles before installation. If
you do not fit the enclosure onto a tiled surface, or seal the tiles
to the tray before installation, water may soak into the wall behind
the wall profiles.
INSTALLATION - Advice and safety
The installation instructions are based on typical use and
conditions.
These products come with the two wall channels pushed onto
each side of the glass panel frame.
These hints have been prepared for your guidance, you must
exercise due care at all times.
For Health and Safety 2 people must carry out the installation
of this enclosure.
Handle glass with care. Although the glass supplied is tough-
ened safety glass (EN12150), impacts can damage both the
glass and the frame.
Warning!
Please check for any hidden pipes or cables before
drilling holes in the wall.
To stop the drill bit slipping, masking tape can be applied to
the tiles when preparing the holes.
When using power tools always follow the manufacturers user
instructions.
Do not sit the enclosure on a bed of silicone, as this will also
stop any water from draining back into the tray.
If the enclosure is sealed to the tray on the inside, any water
that may get into the framework will not be able to drain back
into the tray, this may cause the enclosure to leak.
Leave the silicone sealant to dry for 24 hours before using the
enclosure.
CARE AND CLEANING
Do not use solvents or abrasive material or chemicals to clean
the enclosure.
1
Only clean using soapy water and a soft cloth, rinse
thoroughly afterwards.
INSTALLATION
A

Wall frame sealing strip II x 1
INFINITY SLIDER SINGLE DOOR
2
Drill, 6mm Masonry drill bit, 3.2mm General drill bit, Philips screwdriver, Spirit level, Pencil, Scissors, Knife,Silicone sealant.
Tools and equipment needed
CONTENTS
A
ST4 *40mm screw x 3
ST4 *40mm screw x 3
A
B
M4 *20mm screw x 4
C
D
Cover I x 3
E
Decoration cover I x 2
F
G
Decoration cover II x 1
H
Wall frame sealing strip I x 1
I
Cover for taper sleeve x 2
Wall plug x 6
Waterproof part (LH) x 1
AB
End socket II (LH) x 1
AC
End socket I (LH) x
1
AD
Decoration cover III (LH) x
1
AE
Sleeve x
1
AF
AG
AH
Roller x 2
J
K
Roller clip x 2
M4 *5mm screw x 4
L
Cover II x 1
M
N
End socketof track (RH) x 1
ST4 *12mm screw x 1
O
Side waterproof strip I x 1
P
Side waterproof strip II x 1
Q
Anti-jump rubber strip x 1
R
Decoration cover III (RH) x 1
Wall frame sealing strip I x 1
S
T
U
End socket I (RH) x
1
V
Waterproof part (RH) x 1
W
Waterproof barrier bar x 1
X
End socket II (RH) x
1
Y
Waterproof cap x 1
Z
Handle x
1
AA
End socketof track (LH) x
1
Wall frame
Wall frame
Door
Track
Glass panel
4mm Allen key x 1
AI
Alcohol Prep Pad x
1

Step 1
Step 2
3
A
AA
U
ISLSC1200 1170~1210
1370~1410
1670~1710
ISLSC1400
ISLSC1700
FR

4b
NML
4c
4a
W
N
N
S
T
Step 3
Step 4
4
A
ST
4e
4f
L
4d C
C

AG
AG
D
B
E
E
T
S
Step 5
Step 6
5
A
D

I
Y
Y
V
V
Step 7
Step 8
6
A

AI
O
AA
P
G
G
Step 9
Step 10
7
A

Step 11
8
A
J
K
a1
a3
a4

X
Z
Z
X
J
25~30mm
K
X
L1
L1
Step 12
Step 13
9
A

Q
Q
Q
Q
H
H
Step 14
Step 15
10
A

For any further information please contact Crosswater
Phone number, 0345 873 8840
Website, crosswater.co.uk
Email address, [email protected]
The manufacturer reserves the right to make technical
modifications without prior notice.
Step 16
11
A
24H