Denali HMT.22.10100 User manual

Instruction Rev04
0mm 10 20 30 40 50 60 70 80 90
Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra
mile to make sure our instructions are clear and as easy to understand as possible. If
you have any questions, comments, or suggestions don’t hesitate to give our gear
experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If
you are unsure of your ability to properly install a product, please have the product
installed by your local motorcycle dealer. DENALI takes no responsibility for damages
caused by improper installation. Caution: When installing electronics it is extremely
important to pay close attention to how wires are routed, especially when mounting
products to the front fender, front forks, or fairing of your motorcycle. Always be sure
to turn the handlebars fully left, fully right, and fully compress the suspension to
ensure the wires will not bind and have enough slack for your motorcycle to operate
properly.
Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws,
nuts, and bolts. It is also important to ensure that all hardware is tightened to the
proper torque specifications as listed in your owner’s manual. For included accessory
hardware please refer to the default torque specifications provided below. Inspect all
hardware after the first 30 miles to ensure proper torque specifications are
maintained.
Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.
Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring
countersunk screws.
M3 10.0 in-lbs - 1.0 Nm
M4 23.0 in-lbs - 2.5 Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 - 13.5 ft-lbs 18.0 Nm
M10 - 30.0 ft-lbs 41.0 Nm
M12 - 52.0 ft-lbs 71.0 Nm
in-lbs
ft-lbs NmBolt Size
0in 1 2 3
What’s In The Box?
DENALIELECTRONICS.COM
HMT.22.10100
Ducati Scrambler
SoundBomb Horn Mount
Instruction Manual
(a) Horn Mounting Bracket......(HMT.22.002)................................Qty 1
(b) M6 x 35 DIN 912................................................................Qty 2
(c) M6 Washer DIN 125.............................................................Qty 2
(d) Spacer L:14.288mm ...........................................................Qty 2
Kit Contents
Tools Required: 5mm Allen Key, 13mm open end wrench
(a)
(c)
(b)
(d)

1. Installing The Bracket
1.1 - Installing the Bracket
Step One: Locate the mounting location for your bracket and remove the top factory
screw.
Step Two: Line up the spacer (d), washer (c) and top of the bracket (a) with the
mounting hole and hand tighten with the M6x35mm screw (b). Rotate the bracket
clockwise to gain access to the bottom factory screw and remove it. Rotate the bracket
back and secure the spacer, washer, bracket and M6 screw into the bottom mounting
point and properly tighten both using a 5mm Allen wrench.
DENALIELECTRONICS.COM
1.2 - Mounting the Horn
Step One: Use the hardware supplied with the SoundBomb Horn to attach it to the
bracket. Use a 13mm wrench to tighten the nut on the back side of the mount.
Note: Before fully tightening the horn, you can make small adjustments by slightly
rotating the horn to better match the profile of your bike. The horn should not exceed
10 degrees of tilt and should be as close to 90 degrees upright as possible. When happy
with the position make sure to fully tighten the horn.
Factory
Screw
(Spacer)
(Washer) (M6x35)