Denali SoundBomb DNL.SB.050 User manual

Instruction Rev00
0mm 10 20 30 40 50 60 70 80 90
Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra
mile to make sure our instructions are clear and as easy to understand as possible. If
you have any questions, comments, or suggestions don’t hesitate to give our gear
experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If
you are unsure of your ability to properly install a product, please have the product
installed by your local motorcycle dealer. DENALI takes no responsibility for damages
caused by improper installation. Caution: When installing electronics it is extremely
important to pay close attention to how wires are routed, especially when mounting
products to the front fender, front forks, or fairing of your motorcycle. Always be sure
to turn the handlebars fully left, fully right, and fully compress the suspension to
ensure the wires will not bind and have enough slack for your motorcycle to operate
properly.
Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws,
nuts, and bolts. It is also important to ensure that all hardware is tightened to the
proper torque specifications as listed in your owner’s manual. For included accessory
hardware please refer to the default torque specifications provided below. Inspect all
hardware after the first 30 miles to ensure proper torque specifications are
maintained.
Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.
Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring
countersunk screws.
M3 10.0 in-lbs - 1.0 Nm
M4 23.0 in-lbs - 2.5 Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 - 13.5 ft-lbs 18.0 Nm
M10 - 30.0 ft-lbs 41.0 Nm
M12 - 52.0 ft-lbs 71.0 Nm
in-lbs
ft-lbs NmBolt Size
0in 1 2 3
What’s In The Box?
DENALIELECTRONICS.COM
SoundBomb™ Compact Horn Cover
DNL.SB.050
Instruction Manual
(a) Bracket..............................................................................Qty 1
(b) Cover.................................................................................Qty 1
(c) Decal.................................................................................Qty 1
(d) M5x10 DIN 7991.................................................................Qty 1
(e) M5 Press Nut......................................................................Qty 1
(f) No. 6 x 1” Self Tapping Screw.................................................Qty 1
(g) Spacer...............................................................................Qty 1
Kit Contents
(b)
(a)
(c)
(f)
(g)
(e)
(d)

Assemble The Horn Cover
1. - Install Press Nuts
Step One: From the inside of the Cover (b), install a Press Nut (e) into each hole. The
handle of a screwdriver can be useful to apply pressure to the nuts until they are fully
seated in the plastic.
DENALIELECTRONICS.COM
2. - Place Horn In Cover
Step One: Position the SoundBomb Compact Horn inside of the Cover (b).
3. - Slide Bracket Over Assembly
Step One: With the Soundbomb Compact Horn positioned inside the Cover (b), slide
the Bracket (a) over the entire assembly.
Cover
Press Nut
Cover
SoundBomb Compact Horn
Cover
Bracket
Horn

Assemble The Horn Cover
4. - Attach Bracket To Cover
Step One: Use the M5 Bolts (d) to attach the Bracket (a) to the Cover (b).
DENALIELECTRONICS.COM
Step One: Use the M8 hardware (included with horn) to attach the SoundBomb
Compact Horn to the upper mounting point of the Bracket (b). Do NOT fully tighten.
5.2 - Attach Horn to Bracket (Continued)
Step One: Use the Self Tapping Screw (f) and Spacer (g) to attach the Soundbomb
Compact Horn to the lower mounting point of the Bracket (b).
Step Two: Fully tighten the upper and lower mounting points.
6. - Apply Decal
Step One: Prep and clean the surface of the mounting Bracket (a) using an alcohol
swab.
Step Two: Once dry, apply the Decal (c) to the Bracket (a) being sure the screws are
fully covered and the logo sits centered and parallel to the edges of the bracket.
5.1- Attach Horn to Bracket
Cover
Bracket
Bracket
Screw
Cover
Logo
Bracket
Screw
Nut
Horn
Screw
Spacer
Bracket
Horn