Digilock DAK1-APS1 User manual

Keypad Locks Advanced Security
DAK1-APS1, DAK1-APV1 & DAK1-APH1
Phone: [phone]
www.digilock.com | [email protected]
Assigned Use
Product Guide
Vertical Body
Key Insertion
Digilock logo must face up on standard and vertical body locks. Digilock logo must face left on horizontal body locks.
Standard Body Horizontal Body
Lock Parts
Front Unit
Standard Body
DAK1-APS1
Pull Handle
C Button Key Button
Key Slot LED Usage Indicator
Generation Indicator
Alpha Numeric Keypad
Vertical Body
DAK1-APV1
Key Button
LED Usage Indicator
Generation Indicator
Alpha Numeric
Keypad
C Button
Key Slot
Pull Handle Horizontal Body
DAK1-APH1
LED Usage Indicator C Button
Alpha Numeric Keypad Pull Handle
Key ButtonGeneration Indicator
Key Slot
Rear Unit
Advanced Security
Mounting Holes
Cover Plate
1/2” (12mm) Deadlatch
Cover Plate Screws
Keypad locks operate by entry of a 4-digit code. In assigned use functionality, a 4-digit User Code is assigned to operate the lock.
The user enters the assigned User Code to unlock and closes the door to automatically lock. Management staff operates the lock with
either the Programming Key unique to the lock system or any registered Manager Bypass Key.
User Key
■Operates the lock instead of
User Code
■ADA compliant*
Keys
Manager Bypass KeyProgramming Key
■Registers Manager Bypass Keys
■Provides lock access in case of forgotten/lost user
credential (code or key)
■Allows management audit/inspection
■Provides external power in case of battery failure
■1 Programming Key required per lock system
*US Access Board requires 5% of all
locks to be ADA compliant.
■Assigns User Code and User Key
■Provides lock access in case of forgotten/lost
user credential (code or key)
■Allows management audit/inspection
■Provides external power in case of battery failure
■Up to 25 Manager Bypass Keys may be registered
per lock

Keypad Locks Advanced Security
DAK1-APS1, DAK1-APV1 & DAK1-APH1
Phone: [phone]
www.digilock.com | [email protected]
Assigned Use
Product Guide
Programming Instructions
New locks operate only with = `. Locks must be setup to allow full operation.
Manager Bypass Key(s) can be quickly registered to multiple locks. The Programming Key copies the registered Manager Bypass
Key(s) from one lock to multiple locks.
Initial Setup
Express Register
Up to 25 Manager Bypass Keys may be registered to a lock. If required, contact your Digilock Product Representative to order
additional Manager Bypass Key(s).
a. Go to a lock requiring Manager Bypass Key(s).
b. Press = ` 55 `. The LED will turn on.
c. Touch the Programming Key to the key slot until a two-tone beep is heard.
d. Touch each Manager Bypass Key to the key slot. A two-tone beep will be heard for each Manager Bypass Key that is
successfully registered.
e. Touch the Programming Key to the key slot until a two-tone beep is heard and the LED turns off.
f. Repeat above steps for each lock or follow Express Register instructions to register the same Manager Bypass Key(s) to
multiple locks.
Register/Add Manager Bypass Key(s)
For Lost or Stolen Keys
For a lost or stolen Programming Key:
The lost/stolen Programming Key will continue to operate the lock(s) until it is replaced. Immediately order a Replacement
Programming Key from your Digilock Product Representative. Once received, follow enclosed instructions to set up the lock(s) to
operate with the Replacement Programming Key.
For a lost or stolen Manager Bypass Key(s):
a. Go to the lock registered with the Manager Bypass Key(s).
b. Press = ` 66 `. The LED will turn on.
c. Touch the Programming Key to the key slot until a two-tone beep is heard and the LED turns off.
d. At each lock to be registered, touch the Programming Key to the key slot until a two-tone beep is heard and the LED
flashes once to indicate successful registration.
e. End express registration.* Go to any registered lock and press = ` then touch the Programming Key to the key
slot to operate the lock.
*The Programming Key will continue to function in express registration mode until it is used to operate a lock.
a. Touch the Programming Key to the key slot until a two-tone beep is heard and the LED turns on.
b. Touch each Manager Bypass Key to the key slot. A two-tone beep will be heard for each Manager Bypass Key that is
successfully registered.
c. Touch the Programming Key to the key slot until a two-tone beep is heard and the LED turns off.
d. Repeat above steps for each lock or follow Express Register instructions to setup all locks.
Lost/Stolen Manager Bypass Key(s) will continue to operate the lock(s). To prevent the lost/stolen Manager Bypass Key(s) from
operating the lock(s), erase all registered Manager Bypass Key(s) and register only the remaining Manager Bypass Key(s).
a. Collect all remaining Manager Bypass Key(s).
b. Press = ` 55 `. The LED will turn on.
c. Touch the Programming Key to the key slot until a two tone beep is heard.
d. Touch the Programming Key to the key slot again until three sets of two-tone beeps are heard and the LED turns off.
All previously registered Manager Bypass Key(s) have been erased from the lock.
e. Follow Register/Add Manager Bypass Key(s) instructions to register the remaining Manager Bypass Key(s).

Keypad Locks Advanced Security
DAK1-APS1, DAK1-APV1 & DAK1-APH1
Phone: [phone]
www.digilock.com | [email protected]
Assigned Use
Product Guide
Operating Instructions
Operate with the assigned User Code:
▪To unlock: Press = ____ ` . The latch will retract for approximately 6 seconds to allow the door to be opened.*
▪To lock: Close the door.
Operate with the assigned User Key:
▪To unlock: Touch the assigned User Key to the key slot. The latch will retract for approximately 6 seconds to allow the door to
be opened.
▪To lock: Close the door.
Operate with a registered Manager Bypass Key:
▪To unlock: Touch a registered Manager Bypass Key to the key slot. The latch will retract for approximately 6 seconds to allow
the door to be opened.
▪To lock: Close the door.
Operate with the Programming Key:
▪To unlock: Press = `, then touch the Programming Key to the key slot. The latch will retract for approximately 6 seconds
to allow the door to be opened.
▪To lock: Close the door.
(assigned User Code)
a. Press = `, then touch a registered Manager Bypass Key to the key slot until the LED turns on.
b. Touch any User Key to the key slot until a two-tone beep is heard and the LED turns off.
Assign a User Key
*Once a User Credential is assigned, the previous User Credential will no longer operate the lock.
Assign User Credential (User Code or User Key)*
Assign a User Code (Default User Code = 1234)
a. Press = `, then touch a registered Manager Bypass Key to the key slot until the LED turns on.
b. Press = ____ `. A two-tone beep will be heard.
c. Confirm entry. Press = ____ `. Two sets of two-tone beeps will be heard and the LED will turn off.
(new 4-digit User Code)
(same 4-digit User Code)
*The lock will go into “Sleep Mode” after 3 consecutive incorrect entries.

Keypad Locks Advanced Security
DAK1-APS1, DAK1-APV1 & DAK1-APH1
Assigned Use
Product Guide
Phone: [phone]
www.digilock.com | [email protected]
Error Condition Indicator
Locks emit feedback when an error condition exists.
2 sets of three beeps:
The batteries are low. Replace the batteries.
1 beep:
The lock does not recognize the User Code or Key.
The lock is binding which means that either door alignment or items in the locker are preventing the lock from operating. Press on the
door while operating the lock. If error condition persists, contact Digilock Support for assistance.
10 rapid beeps:
Does not Operate with a Manager Bypass Key
The lock does not recognize the Manager Bypass Key. Follow Register/Add Manager Bypass Key(s) instructions to register
the Manager Bypass Key to the lock. For immediate access, operate with another registered Manager Bypass Key or with the
Programming Key.
Does not Operate with the Programming Key
The lock does not recognize the Programming Key. Contact Digilock Support for assistance.
Does not Unlock with the User Code or User Key
The lock does not recognize the User Code or User Key. Follow Assign User Credential instructions to assign a new User Code or
User Key to the lock. For immediate access, operate the lock with a registered Manager Bypass Key.
Support
Sleep Mode
After three consecutive incorrect User Code entries to unlock, the lock will go into “Sleep Mode” for one minute and for an additional
minute for each subsequent incorrect entry. The keypad is disabled while in “Sleep Mode”.
PG-DAK1-AP-DEN
021314
No Audible Feedback when = is Pressed
a. The lock may be in “Sleep Mode” or the batteries need to be replaced. For immediate access, operate with a registered Manager
Bypass Key. Press = to test; if no audible feedback, replace the batteries.
b. If error condition persists, loosen the mounting hardware and test.
c. If error condition persists, remove the lock and assemble in your hand to test. If the door is locked or damage is visible, contact
Digilock Support.
d. If the lock functions when assembled in your hands, reinstall and test again.
e. If error condition persists, contact Digilock Support.
Battery Replacement
2
Remove the screws and the
cover plate.
1
The batteries are located in
the rear unit of the lock.
3
Pull the battery pack from the
rear housing.
Replace with four premium
alkaline AA batteries.
4
Place the battery pack back
into the rear housing and
screw cover plate in place.