Digilock numeris aspire User manual

Installation Guide
5G Rear Units (Latch and Bolt)
4G Rear Units (Latch and Bolt)

Table of Contents
Before Lock Installation..................................................................................................................................................................................................................................3
Surface Mount Installation
For door thickness measuring between .16” - .91” (4 mm - 23 mm)
Required Components...............................................................................................................................................................................................................4
Installation.........................................................................................................................................................................................................................................5
For door thickness measuring between .01" - .16" (0.2mm - 4 mm)
Required Components...............................................................................................................................................................................................................7
Installation.........................................................................................................................................................................................................................................8
Door Preparation
Strike Plate Installation
Required Components............................................................................................................................................................................................................10
Installation......................................................................................................................................................................................................................................11
Door Mounting Holes Drill Instructions and Template
Drill Instructions.........................................................................................................................................................................................................................12
Template for Standard & Vertical Body......................................................................................................................................................................13
Metal Door Preparation
Compatibility Guide.............................................................................................................................................................14
Removal of 3-hole Lock Plug............................................................................................................................................14
Removal of Padlock Hasp..................................................................................................................................................15

3
The door must have door mounting holes.
Door Mounting Holes
The door must be prepared for lock installation.
Before Lock Installation
1. A strike plate must be installed.
Strike Plate
Angled Strike Plate
Security Strike Plate
Recommended for latch products
Double Door Strike Plate
1
2
1 - Legacy Rear Units
This installation guide is compatible for 4G Motorized Rear Units
Deadbolt - Cable Deadlatch - Cable Deadbolt - Cable Deadlatch - Cable

4
For door thickness measuring between .16" - .91" (4 mm - 23 mm)
Required Components
1*- Phillips Head Screwdriver (#2)
*Not included
2 - Phillips Head Screws
D
C
B
A
Screw
Size Length Door Thickness
Min Max
A 1" (25.400 mm) .01" (.2 mm) .16" (4 mm)
B 1 1/4" (31.750 mm) .16" (4 mm) .43" (11 mm)
C 1 1/2" (38.100 mm) .43" (11 mm) .67" (17 mm)
D 1 3/4" (44.450 mm) .67" (17 mm) .91" (23 mm)
2 - Split Lock Washers
Surface Mount Installation
Tab Text
Standard Keypad
Vertical Body
Touch RFID
Vertical Body
Touch RFID
Standard Body
Standard Keypad
Standard Body
1 - Rear Units
Deadbolt - Cable Deadlatch - Cable

5
REAR VIEW FRONT VIEW
1
With the rear unit behind the door, extend the cable through the door’s mounting hole.
Installation
For illustration, a keypad front unit with a bolt rear unit is used.
REAR VIEW FRONT VIEW
3
Hold the front and rear units against the door and secure with the mounting screws. Ensure the remaining cable is not pinched.
REAR VIEW FRONT VIEW
2
Orient the cable with the red wire position on the top of the ribbon (see g-1). Attach the cable to the front unit using the corresponding
channel guides to ensure the snap connector is properly secured. Once connected a triple beep indicates successful connection.
g.-1

6
Repeat test with the door closed.
If ten rapid beeps are heard, the strike plate or door alignment may need adjustment to allow the lock to operate properly.
If the door does not lock when the bolt/latch is extended, the strike plate or lock position may need adjustment.
For keypad locks with deadbolt rear units:
Press = ` to extend the bolt.
Press = ` again to retract the bolt.
For keypad locks with deadlatch rear units:
Press = ` to retract the latch.
The latch will extend automatically.
For touch RFID locks with deadbolt rear units:
Touch `to extend the bolt.
Touch `again to retract the bolt.
For touch RFID locks with deadlatch rear units:
Touch `to retract the latch.
The latch will extend automatically.
REAR VIEW FRONT VIEW
4
Test the lock while the door is open to ensure that the bolt or latch is operating properly.

7
Required Components
Surface Mount Installation
For door thickness measuring between .01” - .16” (0.2 mm - 4 mm)
1* - 3/8” Nut Driver
*Not included
2 - Locking Nuts
1 - Rear Units
Deadbolt - Cable Deadlatch - Cable
Tab Text
Standard Keypad
Vertical Body
Touch RFID
Vertical Body
Touch RFID
Standard Body
Standard Keypad
Standard Body

8
Installation
REAR VIEW FRONT VIEW
2
Hold the front unit against the front of the door. Use the rear unit mounting holes as a guide, then slide the front and rear units together.
Make sure the connector pins align properly with the connector.
If properly connected, a triple beep will be heard and the LED will ash three times.
For illustration, a keypad front unit with a bolt rear unit is used.
REAR VIEW FRONT VIEW
1
Insert the front unit screw posts through the door mounting holes.
REAR VIEW FRONT VIEW
3
Insert the locking nuts on the screw posts and tighten using the ratchet/screw gun. Do not over tighten.

9
Repeat test with the door closed.
If ten rapid beeps are heard, the strike plate or door alignment may need adjustment to allow the lock to operate properly.
If the door does not lock when the bolt/latch is extended, the strike plate or lock position may need adjustment.
For keypad locks with deadbolt rear units:
Press = ` to extend the bolt.
Press = ` again to retract the bolt.
For keypad locks with deadlatch rear units:
Press = ` to retract the latch.
The latch will extend automatically.
For touch RFID locks with deadbolt rear units:
Touch `to extend the bolt.
Touch `again to retract the bolt.
For touch RFID locks with deadlatch rear units:
Touch `to retract the latch.
The latch will extend automatically.
REAR VIEW FRONT VIEW
4
Test the lock while the door is open to ensure that the bolt/latch is operating properly.

10
Strike Plate Installation
Required Components
1. A strike plate must be installed.
Strike Plate*
Angled Strike Plate
Security Strike Plate
Recommended for latch products
Double Door Strike Plate
1*- Phillips Head Screwdriver (#1)
1*- Drill
1*- Pencil
1*- 1/6” Drill bit
Removable tape*
1*- 5/16” Drill bit
1*- Ruler
1*- 3/4” Drill bit
Door Preparation
*Not included

11
Installation
Position the strike plate on the door frame aligning it with
the center of the lock’s mounting holes.
Door Frame
0.32 in
(8 mm)
Mark Here
1
Drill 0.25" (6.35 mm) pilot holes using a 1/6" drill bit.
Door Frame
Drill Pilot
Holes Here
3
Adjust the strike plate to the proper position (.32" (8 mm)
from the door edge) then tighten the self tapping screws.
Door Frame
0.32 in
(8 mm)
5
Allow .32" (8 mm) from door edge and mark the position
of the adjustment slot holes.
Door Frame
0.32 in
(8 mm)
Mark Here
2
Position the strike plate and the self tapping screws into the
adjustment slot holes. Do not tighten the screws.
Door Frame
4
Position and tighten the remaining self tapping screw
into the center hole.
Door Frame
6

12
Door Mounting Holes Drill Instruction and Template
Drill Instructions
With the door open place the Template over the locker frame.
(a) Align the Edge of Strike Plate with the Strike Plate Marker.
(b) Center the Template to the center of the Strike Plate.
You may secure the Template with removable tape.
(a)
(b)
Strike Center
1
Close the door over the Template.
(a) Mark the door edge at the Template Center Line.
(b) Mark the Template with the edge of the door.
(b)
(a)
2
Place the Template on the front of the door.
(a) Align the drawn mark on the Template with the door edge.
(b) Center the Template with the mark on the door.
Secure the Template with removable tape.
(a)
(b)
3
Mark the center points of the door mounting holes on the front of
the door. Drill the holes according the specied dimensions.
Drill x2
5/16” 0.3125 in
(7.94 mm)
Drill 3/4”
0.75 in (19.1 mm)
4

13
Template for Door Mounting Holes
Templates may not print to scale. Check all measurements before proceeding.
All measurements in thousandths
of an inch and millimeters
.300
7.62 (mm)
use 5/16" bit
.905
23 (mm)
.905
23 (mm)
.300
7.62 (mm)
.750
19.05 (mm)
use 3/4" bit
001.1
)mm(9.72
001.1
)mm(9.72
001.1
)mm(9.72
001.1
)mm(9.72
ALIGN EDGE OF
STRIKE PLATE HERE
FOR LEFT
CLOSING DOOR
ALIGN EDGE OF
STRIKE PLATE HERE
FOR RIGHT
CLOSING DOOR
ALIGN EDGE OF
STRIKE PLATE HERE
FOR LEFT
CLOSING DOOR
ALIGN EDGE OF
STRIKE PLATE HERE
FOR RIGHT
CLOSING DOOR
CENTER LINE
CENTER LINE
Before printing, turn o auto scaling in printer setup and print at 100%

14
Metal Door Preparation
Compatibility Guide
Removal of 3-hole Lock Plug
Digilock is compatible with a majority of 3-hole conguration, latch, and handle door types. Some doors may require modication to clear
obstructions.
Remove any obstructions to the door mounting holes.
Single Point Latch
Handle
Standard Lift
Box Locker Padlock Hasp
Rear View of Locker Door with Lock Plug
1 2

15
Removal of Padlock Hasp
1* - Handheld Grinder or Hack Saw
1* - Metal File
*Not included
Close the door and make sure that nothing is
protruding above the surface of the door.
1
Open the door then cut the padlock hasp on
the marked cut-line.
3
Close the door and mark the area to cut the
padlock hasp.
2
Smooth out rough or sharp edges.
4
The padlock hasp must be removed

IG-NM-A-DEN
010919 707 766 6000 | [email protected] | www.digilock.com