DITEC DAS200 User manual

Ditec DAS200
DAS200HD-DAS200RF-DAS200RG
Sliding doors automation
(Original instructions)
Technical manual
www.ditecautomations.com
IP2266EN • 2021-11-15
Last version of this manual

2
IP2266EN
Contents
Key This symbol indicates instructions or notes regarding safety, to which special atten-
tion must be paid.
This symbol indicates useful information for the correct functioning of the product.
Subject Page
General safety precautions 3
EC Declaration of Incorporation 5
1. Technical data 6
2. Standard installation 7
3. Main components 8
4. Installing the automation 9
4.1 Installing / Removing the cover 9
4.2 Installation/removal of the cover if installed side presence sensor 10
5. Examples of installation 11
5.1 Example using supplied wing anchoring brackets 11
5.2 Examples with DAS11M8 12
5.3 Examples with DAS18M8 13
5.4 Example with DAS35M8 14
5.5 Example with DAS40M8 15
5.6 Example with ACV 15
6. Preparation of the glass door wing 16
6.1 Installing and adjusting the door wings 17
6.2 Installing the floor guides 19
6.3 Belt stop installation 19
6.4 Checking and adjusting the belt tension 20
6.5 Sensor positioning on the cover 20
6.6 External sensor cable fixing 20
7. Electrical connections 21
7.1 Standard electrical connections 22
7.2 Control panel commands 24
7.2.1 Commands 24
7.3 DAS902MP plus module (optional, mandatory on DAS200RF) 26
7.4 DAS902MP commands 27
8. Adjustment and selection of control functions 29
8.1 Display test 30
8.2 Status indication on the display 30
9. Start up 31
10. Parameters 34
10.1 Configuration parameters according to function 34
10.2 Main control board parameters 38
11. Example of connection 51
11.1 Combined opening and safety sensor + safety sensor on opening 51
11.2 Interconnection of operators 54
11.2.1 Interconnection cable 54
11.2.2 Hardware configuration for interconnection 54
11.2.3 Parameter configuration for interconnection 55
11.3 Operation mode selector (OMS) functionality 55
11.4 Synchronization 56
11.5 Interlock 56
12. ENTREMATIC DOOR CONNECT App 58
13. Entry-exit traffic control ( Function to be used with the Entrematic Door Connect App) 58
13.1 Flow 58
13.2 How it works 58
13.3 Installation 59
13.4 Sensors 60
13.5 Optimizing performance 60
14. Troubleshooting 61
14.1 Activ error indication 62
15. Routine maintenance plan 66

3
IP2266EN
This installation manual is intended for qualified personnel only •Instal-
lation, electrical connections and adjustments must be performed by
qualified personnel, in accordance with Good Working Methods and in
compliance with the current regulations • Read the instructions carefully
before installing the product. Wrong installation could be dangerous •
Before installing the product, make sure it is in perfect condition •
The packaging materials (plastic, polystyrene, etc.) should not
be discarded in the environment or left within reach of children,
as they are a potential source of danger • Do not install the product
in explosive areas and atmospheres: the presence of inflammable
gas or fumes represents a serious safety hazard • Make sure that
the temperature range indicated in the technical specifications is
compatible with the installation site • Before installing the motori-
zation device, make sure that the existing structure, as well as all
the support and guide elements, are up to standards in terms of
strength and stability. Verify the stability and smooth mobility of the
guided part, and make sure that no risks of fall or derailment sub-
sist. Make all the necessary structural modifications to create safe-
ty clearance and to guard or isolate all the crushing, shearing, trap-
ping and general hazardous areas • The motorization device
manufacturer is not responsible for failure to observe Good Working
Methods when building the frames to be motorized, or for any de-
formation during use • The safety devices (photocells, safety edges,
emergency stops, etc.) must be installed taking into account the ap-
plicable laws and directives, Good Working Methods, installation
premises, system operating logic and the forces developed by the
General safety precautions
ATTENTION! Important safety instructions.
Please follow these instructions carefully. Failure to observe
the information given in this manual may lead to
severe personal injury or damage to the equipment.
Keep these instructions for future reference.
This manual and those for any accessories can be
downloaded from www.ditecautomations.com.

4
IP2266EN
motorized door or gate • The safety devices must protect against
crushing, cutting, trapping and general danger areas of the motori-
zed door or gate. Display the signs required by law to identify hazar-
dous areas. Each installation must bear a visible indication of the
data identifying the motorized door or gate • Before connecting the
power supply, make sure the plate data correspond to those of the
mains power supply. An omnipolar disconnection switch with a con-
tact opening distance of at least 3mm must be fitted on the mains
supply. Check that there is an adequate residual current circuit bre-
aker and a suitable overcurrent cutout upstream of the electrical
installation in accordance with Good Working Methods and with the
laws in force • When requested, connect the motorized door or gate
to an effective earthing system that complies with the current safe-
ty standards • Before commissioning the installation to the end
user, make sure that the automation is adequately adjusted in order
to satisfy all the functional and safety requirements, and that all the
command, safety, and manual release devices operate correctly •
During installation, maintenance and repair operations, cut
off the power supply before opening the cover to access the
electrical parts • The protection cover of the operator must be
removed by qualified personnel only.
The electronic parts must be handled using earthed antista-
tic conductive arms. The manufacturer of the motorization
declines all responsibility if component parts not compatible with
safe and correct operation are fitted • Only use original spare
parts for repairing or replacing products • The installer must
supply all information concerning the automatic, manual and
emergency operation of the motorized door or gate, and must
provide the user with the operation and safety instructions.

5
IP2266EN
EC Declaration of Incorporation
We:
ASSA ABLOY Entrance Systems AB
Lodjursgatan 10
SE-261 44 Landskrona
Sweden
Declare under our sole responsibility that the type of equipment with name:
Ditec DAS200 sliding door operator, sold also in kit form as article DAS200K1
Ditec DAS200HD sliding door operator, sold also in kit form as article DAS200HDK1
Ditec DAS200RG sliding door operator, sold also in kit form as article DAS200RGK1 +
DAS902MP
Ditec DAS200RF sliding door operator, sold also in kit form as article DAS200HDK1 +
DAS200RFKA
Comply with the following directives and their amendments:
2006/42/EC Machinery Directive (MD) for the following essential health and safety
requirements: 1.1.2, 1.1.3, 1.2.1, 1.2.2, 1.2.3, 1.2.4.2, 1.2.6, 1.3.9, 1.4.3, 1.7.2,
1.7.3, 1.7.4, 1.7.4.1, 1.7.4.2.
2014/30/EU Electromagnetic Compatibility Directive (EMCD)
2011/65/EU Restriction of hazardous substances (RoHS 2)
2015/863/EU Restriction of hazardous substances (RoHS 2 Amendment)
Harmonized European standards that have been applied:
EN 60335 -1:2012/A2:2019 EN ISO 13849 -1:2015 EN 61000 -6-2:2005
EN 60335-2-103:2015 EN 16005:2012/AC:2015 EN 61000 -6-3:2007+A1:2011
Other standards or technical specifications that have been applied:
IEC 60335-1: 2010 ed.5 IEC 60335-2-103:2006+A1:2010 AutSchR: 1997
DIN 18650-1:2010 DIN 18650-2:2010
EC type examination or certificate issued by a notified or competent body concerning the equipment:
TÜV SÜD B 058029 0052 (Ditec DAS200)
TÜV SÜD B 058029 0053 (Ditec DAS200HD, Ditec DAS200RG)
TÜV SÜD B 058029 0054 (Ditec DAS200RF)
The manufacturing process ensures the compliance of the equipment with the technical file.
The equipment must not be used until the final installed automatic entrance system has been
declared in compliance with the Machinery Directive 2006/42/EC.
Responsible for technical file:
Matteo Fino
Business Area PGA
Ditec S.p.A.
Largo U. Boccioni, 1
21040 Origgio (VA)
Italy
Signed for and on behalf of ASSA ABLOY Entrance Systems AB by:
Place Date Signature Position
Origgio 2021-11-15 Matteo Fino President B.A. PGA
Mat
M
Mat
Ma
M
M
M
M
Mat
M
M
M
M
M
M
M
Mat
M
M
M
M
M
M
M
M
Mat
teo
t
t
t
t
t
t
t
t
t
t
t
t
Fi
no
n
o
o
no
o
no
no
no
o
o
no
no
no
no
no
no
no
n
no
no
no
no
no
o
n
n
n
n
n
n
n
n
© ASSA ABLOY, All rights reserved

6
IP2266EN
1. Technical data
Ditec DAS200 Ditec DAS200HD
Ditec DAS200RF Ditec DAS200RG
Power supply 100 V~ / 240 V~, -10%/ +10%
50/60 Hz
100 V~ / 240 V~, -10%/ +10%
50/60 Hz
100 V~ / 240 V~, -10%/ +10%
50/60 Hz
Power consumption Max 100 W Max 250 W Max 250 W
Power supply rated
power (PS) 75 W 150 W 150 W
Max Opening speed
(2 door wings) 1,6 m/s 1,6 m/s 1,6 m/s
Maximum load 120 kg (1 wing)
200 kg (2 wings)
150kg (1 wing)
DAS200HD 280 kg (2 wings)
DAS200RF 240 kg (2 wings)
150 kg (1 wing)
280 kg (2 wings)
Intermittence S3= 100% S3= 100% S3= 100%
Temperature
-20°C +50°C -20°C +50°C -20°C +50°C
Degree of protection IP20
(FOR INTERNAL USE ONLY)
IP20
(FOR INTERNAL USE ONLY)
IP20
(FOR INTERNAL USE ONLY)
Control panel
(MCU/MCU-ER) 1DAS20QE 1DAS20HDQE 1DAS20RGQE
Accessories power
supply 24 V 0,64 A 24 V 1 A 24 V 1 A
Durability test 1.000.000 cycles 1.000.000 cycles 1.000.000 cycles
TYPE OF USE Ditec DAS200 Ditec DAS200HD Ditec DAS200RF Ditec DAS200RG
Sliding door auto-
mation
Escape route with
break-out system
Escape route
with rubber band
opening system
Escape route with
redundant system

7
IP2266EN
2. Standard installation
Ref. Description
1Automation for sliding doors
2
3Combined opening and safe closing sensor
4Safe opening sensor
5Program selector
AConnect the power supply cable to a type-approved omnipolar switch with category III insulation and
a contact opening distance of at least 3 mm.
The connections to the mains and low voltage wires must be made on an independent channel sep-
arated from the connections to the command and safety devices (SELV = Safety Extra Low Voltage).
1
32
A
5
4
4

8
IP2266EN
3. Main components
NOTE: the given operating and performance features can only be guaranteed with the
use of DITEC accessories and safety devices.
Ref. Code Description
6 DASLOKSB Built-in manual release device (optional)
7- Mains power supply
81DAS20AL
1DAS20HAL
75W power supply unit (PS)
150W power supply unit (PS)
9
1DAS20MR
1DAS20HMR
1DAS20RGMR
DAS200 gearmotor
DAS200HD gearmotor
DAS200RG gearmotor
10
1DAS20QE
1DAS20HDQE
1DAS20RGQE
DAS200 control panel (MCU)
DAS200HD-DAS200RF control panel (MCU)
DAS200RG control panel (MCU-ER)
11 DAS902MP DAS902MP plus module
12 DAS901BAT1
DAS902BAT2
12V batteries (set parameter 43= 05)
24V batteries (the fuse in the cable harness is T10A)
13 DAS802B50 Drive belt
14
DAS802LOK
DAS802LOKA
DAS802LOKB
Standard lock. Locked with power - LD
Anti-panic lock. Locked without power - LDP
Bi-stable lock-LDB
15 - Belt transmission
16 - Mechanical stops
78912
10 11 13 14
16
615

1
2
3
CLICK
500
9
IP2266EN
4. Installing the automation
4.1 Installing / Removing the cover
• Secure and unsecure the open cover as shown below.

10
IP2266EN
4.2 Installation/removal of the cover if installed side presence
sensor
1
2
3