DSC 3G2060 User manual

3G2060
HSPA Cellular Alarm Communicator – International
TL2603G
Internet and HSPA Dual-path Alarm Communicator –
International
TL260
Internet Alarm Communicator – International
INSTALLATION MANUAL V3.0
Warning: This manual contains information on limitations regarding product use and func-
tion and information on the limitations as to liability of the manufacturer.

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Communicator Frequency Bands by Market . . . . . . . . . . . . . . . . . . . . . . . . 2
Ratings Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pre Installation Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Communicator Installation Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installing the Ethernet Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Inserting and Removing the SIM Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installing the Ethernet Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installing Cellular/Ethernet Communicator in Panel . . . . . . . . . . . . . . . . . . 5
Communicator Placement Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Initial Panel Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Communicator Status Leds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Communicator Reset / Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Programming Options Sections
Ethernet/Cellular Programming Options. . . . . . . . . . . . . . . . . . . . . . . . . . . 14
System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Programming Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Communications Reporting Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Ethernet Receiver 1 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Ethernet Receiver 2 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Ethernet Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cellular Receiver 1 Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cellular Receiver 2 Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Cellular Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
System Information (Read Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
System Reset Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Communicator Status, Initialization, Diagnostics and Troubleshooting . . . . . . 26
Programming Worksheets Sections
Ethernet/Cellular Programming Worksheets . . . . . . . . . . . . . . . . . . . . . . . 30
System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Ethernet Receiver 1 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Ethernet Receiver 2 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Ethernet Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Cellular Receiver 1 Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Cellular Receiver 2 Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Cellular Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Event Notification/Interactive Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Area Label Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
User Label Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Zone Label Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
External Event Label Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Internal Event Label Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
SMS Interactive Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
System Information (Read Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
System Reset Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
TABLE OF CONTENTS

WARNING: INSTALLER PLEASE READ CAREFULLY
Note to Installers
The Warnings on this page contain vital information. As the only
individual in contact with system users, it is the installer’s responsi-
bility to bring each item in this Warning to the attention of all users
of this system.
System Failures
This system has been carefully designed to be as effective as possi-
ble. There are circumstances, however, involving fire, burglary, or
other types of emergencies where it may not provide protection. Any
alarm system of any type may be compromised deliberately or may
fail to operate as expected for a variety of reasons. Some, but not all,
of the reasons may be:
Access by Intruders
Intruders may enter through an unprotected access point, circumvent
a sensing device, evade detection by moving through an area of
insufficient coverage, disconnect a warning device, or interfere with
or prevent the proper operation of the system.
Component Failure
Although every effort has been made to make this system as reliable
as possible, the system may fail to function as intended due to the
failure of a component.
Compromise of Radio Frequency (Wireless) Devices
Signals may not reach the receiver under all circumstances which
could include metal objects placed on or near the radio path or delib-
erate jamming or other inadvertent radio signal interference.
Criminal Knowledge
This system contains security features which were known to be
effective at the time of manufacture. It is possible for persons with
criminal intent to develop techniques which reduce the effectiveness
of these features. It is important that your security system be
reviewed periodically to ensure that its features remain effective and
that it is updated or replaced if it is found that it does not provide the
protection expected.
Failure of Replaceable Batteries
This system’s wireless transmitters have been designed to provide
several years of battery life under normal conditions. The expected
battery life is a function of the device environment, usage, and type.
Ambient conditions such as high humidity, high or low temperatures,
or large temperature fluctuations may reduce the expected battery
life. While each transmitting device has a low battery monitor which
identifies when the batteries need to be replaced, this monitor may
fail to operate as expected. Regular testing and maintenance will
keep the system in good operating condition.
Inadequate Installation
A security system must be installed properly in order to provide ade-
quate protection. Every installation should be evaluated by a security
professional to ensure that all access points and areas are covered.
Locks and latches on windows and doors must be secure and operate
as intended. Windows, doors, walls, ceilings and other building
materials must be of sufficient strength and construction to provide
the level of protection expected. A reevaluation must be done during
and after any construction activity. An evaluation by the fire and/or
police department is highly recommended if this service is available.
Inadequate Testing
Most problems that would prevent an alarm system from operating as
intended can be found by regular testing and maintenance. The com-
plete system should be tested weekly and immediately after a break-
in, an attempted break-in, a fire, a storm, an earthquake, an accident,
or any kind of construction activity inside or outside the premises.
The testing should include all sensing devices, keypads, consoles,
alarm indicating devices, and any other operational devices that are
part of the system.
Insufficient Time
There may be circumstances when the system will operate as
intended, yet the occupants will not be protected from an emergency
due to their inability to respond to the warnings in a timely manner. If
the system is remotely monitored, the response may not occur in time
to protect the occupants or their belongings.
Motion Detectors
Motion detectors can only detect motion within the designated areas
as shown in their respective installation instructions. They cannot
discriminate between intruders and intended occupants. Motion
detectors do not provide volumetric area protection. They have mul-
tiple beams of detection and motion can only be detected in unob-
structed areas covered by these beams. They cannot detect motion
which occurs behind walls, ceilings, floor, closed doors, glass parti-
tions, glass doors or windows. Any type of tampering whether inten-
tional or unintentional such as masking, painting, or spraying of any
material on the lenses, mirrors, windows or any other part of the
detection system will impair its proper operation.
Passive infrared motion detectors operate by sensing changes in tem-
perature. However their effectiveness can be reduced when the ambi-
ent temperature rises near or above body temperature or if there are
intentional or unintentional sources of heat in or near the detection
area. Some of these heat sources could be heaters, radiators, stoves,
barbecues, fireplaces, sunlight, steam vents, lighting and so on.
Power Failure
Control units, intrusion detectors, smoke detectors and many other
security devices require an adequate power supply for proper opera-
tion. If a device operates from batteries, it is possible for the batteries
to fail. Even if the batteries have not failed, they must be charged, in
good condition and installed correctly. If a device operates only by
AC power, any interruption, however brief, will render that device
inoperative while it does not have power. Power interruptions of any
length are often accompanied by voltage fluctuations which may
damage electronic equipment such as a security system. After a
power interruption has occurred, immediately conduct a complete
system test to ensure that the system operates as intended.
Security and Insurance
Regardless of its capabilities, an alarm system is not a substitute for
property or life insurance. An alarm system also is not a substitute
for property owners, renters, or other occupants to act prudently to
prevent or minimize the harmful effects of an emergency situation.
Smoke Detectors
Smoke detectors that are a part of this system may not properly alert
occupants of a fire for a number of reasons, some of which follow.
The smoke detectors may have been improperly installed or posi-
tioned. Smoke may not be able to reach the smoke detectors, such as
when the fire is in a chimney, walls or roofs, or on the other side of
closed doors. Smoke detectors may not detect smoke from fires on
another level of the residence or building.
Every fire is different in the amount of smoke produced and the rate
of burning. Smoke detectors cannot sense all types of fires equally
well. Smoke detectors may not provide timely warning of fires
caused by carelessness or safety hazards such as smoking in bed, vio-
lent explosions, escaping gas, improper storage of flammable materi-
als, overloaded electrical circuits, children playing with matches, or
arson.
Even if the smoke detector operates as intended, there may be cir-
cumstances when there is insufficient warning to allow all occupants
to escape in time to avoid injury or death.
Telephone Lines
If telephone lines are used to transmit alarms, they may be out of ser-
vice or busy for certain periods of time. Also an intruder may cut the
telephone line or defeat its operation by more sophisticated means
which may be difficult to detect.
Warning Devices
Warning devices such as sirens, bells, horns, or strobes may not warn
people or waken someone sleeping if there is an intervening wall or
door. If warning devices are located on a different level of the resi-
dence or premise, then it is less likely that the occupants will be
alerted or awakened. Audible warning devices may be interfered
with by other noise sources such as stereos, radios, televisions, air
conditioners, other appliances, or passing traffic. Audible warning
devices, however loud, may not be heard by a hearing-impaired per-
son.

1
General 3G Alarm Communicator Installation Manual
IMPORTANT
This installation manual shall be used in conjunction with the PowerSeries control panel. All the
safety instructions specified within that manual shall be observed (or equivalent). The PowerSer-
ies control panel is referenced as the “panel” throughout this document.
The Cellular/Internet Communicator is a fixed, wall-mounted unit, located inside the panel, and
shall be installed in the location specified in these instructions.The equipment enclosure must be
fully assembled and closed, with all the necessary screws/tabs, and secured to a wall before opera-
tion. Internal wiring must be routed in a manner that prevents:
• Excessive strain on wire and on terminal connections,
• Interference between power limited and non power limited wiring,
• Loosening of terminal connections, or
• Damage of conductor insulation.
WARNING: Never install this equipment during a lightning storm!
Safety Information
The Installer must instruct the System user on each of the following:
• Do not attempt to service this product. Opening or removing covers may expose the user to
dangerous voltages or other risks.
• Any servicing shall be referred to service persons only.
• Use authorized accessories only with this equipment.
• Do not stay close to the equipment during device operation.
• Do not touch the external antenna.
Model Information
3G2060: Is a HSPA (3G) Cellular Alarm Communicator that sends alarm communication to
Sur-Gard SG-System I, II, III (SG-DRL3IP), IV (SG-DRL4IP) and 5 (SG-DRL5IP) central station
receivers via a HSPA(3G)/GPRS digital cellular network.
TL2603G: Is a Dual-path HSPA(3G) Internet Alarm Communicator that sends alarm communica-
tion to SG-System I, II, III, IV and 5 central station receivers through Internet or a HSPA(3G)/
GPRS digital cellular network.
TL260: Is an Ethernet only alarm Communicator that sends alarm communication to SG-System
I, II, III, IV and 5 central station receivers through a wired Ethernet/Internet connection.
The communicator can be used as either a backup or primary communicator. The communicator
supports Internet Protocol (IP) transmission of panel and communicator events over Internet and/
or HSPA/GPRS.
The cellular performance of the 3G2060 or TL2603G Communicator depends greatly on
HSPA(3G)/GPRS network coverage in the local area. The unit should not be mounted in the final
location without first performing the Communicator Placement Test below to determine the best
location for radio reception (minimum of one green LED ON).
NOTE: Prior to installation of the 3G2060 or TL2603G Communicator, confirm with your local
service provider that the HSPA(3G)/GPRS network is available and active in the area where the
communicator will be installed, and that radio signal strength (CSQ) is adequate.
NOTE: For Mexico and South America (excluding Brazil) the following model names are avail-
able: TL2603G-LAT/3G2060-LAT. For the European market the following model name is avail-
able: TL2603G-EU/3G2060-EU. For Australia, New Zealand and Brazil the following model
name is available: TL2603G-AU/3G2060-AU. The Generic name "3G2060/TL2603G" used
throughout this manual is representative of all models unless otherwise indicated.
Panel Mounting
The following communicators are compatible with PC1616/PC1832/PC1864 panels:
•3G2060 (HSPA(3G)/GPRS only)
•TL2603G (Internet + HSPA(3G)/GPRS dual-path)
•TL260 (Internet Only)
GENERAL

2
General 3G Alarm Communicator Installation Manual
Features
• 128-bit AES encryption via cellular and Internet (NIST Validation Certificate No. 2032).
• Back up or primary cellular alarm communication.
• Automatically switches to 2G (EDGE/GPRS) if HSPA(3G) service is not available.
• Ethernet LAN/WAN 10/100 BaseT (TL2603G/TL260 only).
• Full event reporting to central station.
• Fully redundant Internet and cellular Dual-path Alarm Communication (TL2603G only).
• Individual Ethernet and/or Cellular periodic test transmission.
• Integrated call routing.
• Remote firmware upgrade capability of the communicator and panel firmware via Ethernet and/
or cellular.
• Panel remote uploading/downloading support via cellular and Internet.
• PC-LINK connection.
• Programmable Labels.
• SIA and Contact ID (CID) formats supported.
• Signal strength and Trouble display LEDs.
• Supervision heartbeats sent via cellular and Internet.
Communicator Frequency Bands by Market
Table 1: 2G Frequency Bands - All Markets
Table 2: 3G Frequency Bands - Europe
Table 3: 3G Frequency Bands - Australia, New Zealand and Brazil
Table 4: 3G Frequency Bands - Mexico and South America (excluding Brazil)
Transmit Direction Cellular 900 DCS 1800 GSM-850 PCS 1900
Transmit Frequency 880 MHz to 915 MHz 1710 MHz to 1785 MHz 824MHz–849MHz 1850 MHz to 1909 MHz
Receive Frequency 925 MHz to 960 MHz 1805 MHz to 1880 MHz 869MHz–894MHz 1930MHz to 1989 MHz
Transmit Direction UMTS 900 UMTS 2100 (IMT)
Transmit Frequency 882.4 MHz to 912.6 MHz 1922.4 MHz to 1977.6 MHz
Receive Frequency 927.4 MHz to 957.6 MHz 2112.4 MHz to 2167.6 MHz
Transmit Direction UMTS 850 (CLR) UMTS 2100 (IMT)
Transmit Frequency 826.4 MHz to 846.6 MHz 1922.4 MHz to 1977.6 MHz
Receive Frequency 871.4 MHz to 891.6 MHz 2112.4 MHz to 2167.6 MHz
Transmit Direction Cellular 850 North America PCS 1900 North America
Transmit Frequency 824 MHz to 849MHz 1850 MHz to 1910 MHz
Receive Frequency 869 MHz to 894MHz 1930 MHz to 1990 MHz

3
Pre Installation Configuration 3G Alarm Communicator Installation Manual
Ratings Compatibility
NOTE: Enter [*][8][Installer Code][900] at keypad to view the Panel Version number.
Remote Programming via DLS 5:
Before programming, you will require your network’s Public IP Address and Public listening port
for incoming DLS 5connections. You must send an SMS message to the unit, therefore, you must
know the phone number assigned to the SIM.
1. Run the DLS 5 software on your computer. If required, download the DLS 5 software from DSC:
http://www.dsc.com/index.php?n=library#self.
2. Create an account for the Panel/Communicator, select the Communicator type (e.g., SMS -
3G2060) and enter all relevant information under SMS section, including the Communicator’s
cellular telephone number.
3. All available Communicator and panel options can be configured in the DLS 5 account. Refer
to Panel Installation Guide and Communicator Manual for detailed programming information.
Also, refer to your DLS 5 manual and Help file.
4. When you have finished programming the account, click Global Download and choose SMS as
Connection Type. Click OK.
5. DLS 5 will generate the required text for the SMS message. This message has the Public IP and
Port Number of the DLS Server to allow the Communicator to link up with your computer.
Type the SMS message in to your cell phone and send to the Communicator’s cellular phone
number. Then Click OK.
6. The SMS message will trigger the unit to establish a connection to your DLS 5 software. New
programming of the Communicator will be downloaded to the unit remotely via cellular or
Table 5: Communicator Ratings
Model 3G2060
Cellular only
TL2603G
Ethernet and Cellular
TL260
Ethernet only
Power Supply Ratings
• Input Voltage
Nominal 12 VDC:
The panel Bell output shall be derated:
700mA - (Communicator mA) = (derated Bell output).
Current Consumption
• Standby Current 90mA @ 13.66V 120mA @ 13.66V 100mA @ 13.66V
• Alarm (Transmitting) Current 400mA @ 12V
• Operating Frequency 850MHz, 1900MHz N/A
• Typical Antenna Gain 2dBiN/A
Environmental Specifications
Operating Temperature 32°F - 120°F (0°C - 49°C)
Humidity 5% ~ 93% relative humidity, non-condensing
Mechanical Specifications
Board Dimensions (mm) 100 × 150 × 15 100 × 150 × 15 100 × 150 × 15
Weight (grams) with bracket 310 320 290
Table 6: Compatible Receivers, and Panels
Communicator Receiver/
Panel Description
3G2060
TL2603G/TL260
Receiver
• SG-System I Receiver, version 1.13+
• SG-System II Receiver, version 2.10+
• SG-DRL3-IP, version 2.30+ (for SG-System III Receiver)
• SG-DRL4-IP version 1.20+ (for SG-System IV Receiver)
• SG-DRL5-IP version 1.00+ (for SG-System 5 Receiver)
Panel
• Power Series PC1616, version 4.5+
• Power Series PC1832, version 4.5+
• Power Series PC1864, version 4.5+
PRE INSTALLATION CONFIGURATION

4
Communicator Installation Configuration 3G Alarm Communicator Installation Manual
Ethernet/Internet. The actual path for the downloading will be determined by the Communica-
tor’s communication settings in Section [851][005], Toggle Option [4].
NOTE: You can disable DLS over cellular. Refer to Programming Worksheets Section [006] Tog-
gle Option [7]. If you disable DLS over cellular, remote programming will not work on the
3G2060 Communicator, regardless of the path set in Programming Options Section [005] Toggle
Option [4].
Encryption
The Communicator uses 128 Bit AES Encryption. Encryption can only be enabled from the moni-
toring station receiver. Each receiver (Ethernet 1 and 2, cellular 1 and 2) can independently have
encryption enabled or disabled. When encryption is enabled, the central station will configure the
device to encrypt communications the next time the Communicator module performs a communi-
cation to that receiver.
NOTE: Packets will start being encrypted only after the next event is sent to that receiver, or if the
unit is restarted.
Before leaving the installation site, the Communicator TL2603G/TL260 Ethernet line shall be
connected via an APPROVED (acceptable to the local authorities) Network Interface Device
(NID). All wiring shall be performed according to the local electrical codes.
This Cellular/Ethernet Communicator shall be installed by service persons only (service person is
defined as a person having the appropriate technical training and experience necessary to be aware
of hazards to which that person may be exposed to in performing a task and can also take measures
to minimize the risks to that person or other persons). The Communicator shall be installed and
used within an environment that provides the pollution degree max 2, overvoltages category II, in
non-hazardous, indoor locations only. This manual shall be used with the Installation Manual of
the panel which is connected to the Cellular/Ethernet Communicator. All instructions specified
within the panel manual must be observed.
All the local rules imposed by local electrical codes shall be observed and respected during instal-
lation.
Installing the Ethernet Cable
TL2603G/TL260 only
A Category 5 (CAT 5) Ethernet cable must be run from a source with Internet connectivity to the
Communicator module, inside the Panel. The Communicator end of the cable must be terminated
with an RJ45 plug, which will connect to the Communicator’s RJ45 jack after the Communicator
is installed. All requirements for installation of CAT5 Ethernet cable must be observed for correct
operation of the Communicator, including, but not limited to, the following:
• Do NOT strip off cable sheathing more than required for proper termination.
• Do NOT kink/knot cable.
• Do NOT crush cable with cable ties.
• Do NOT untwist CAT5 pairs more than ½ in. (1.2cm).
• Do NOT splice cable.
• Do NOT bend cable at right angles or make any other sharp bends.
NOTE: CAT5 specification requires that any cable bend must have a minimum 2 in. (5 cm) bend
radius. Maximum length of CAT 5 cable is 328 ft. (100 m).
Inserting and Removing the SIM Card
1. Remove the front cover of the panel to access SIM holder.
2. Remove power from the panel and disconnect the battery and telephone line.
3. On the SIM card holder push gently to slide the cover downwards to OPEN. This will unlatch
the SIM card holder on the top edge of the communicator PCB. (See Figure 3).
4. Tilt the top of the SIM card holder downwards to access the SIM card.
5. The SIM can be damaged by bending or scratching contacts. Use caution when handling SIM
cards.
COMMUNICATOR INSTALLATION CONFIGURATION

5
Installing Cellular/Ethernet Communicator in 3G Alarm Communicator Installation Manual
6. Insert or remove the SIM card, noting the orientation of the notches on the SIM card and the
SIM card holder.
7. When inserting a SIM card, insert the card in the proper orientation and gently push the SIM
card holder down and slide the holder as indicated by the arrow on SIM holder, to LOCK.
8. Reconnect the backup battery and telephone line, apply AC power to panel, and replace the
panel cover.
Hardware Reset
The Communicator can be hardware reset by installing a jumper between Pins 4 and 5 on the
AUDIO/DEFAULT connector and restarting the Communicator. Installing jumper during normal
operation has no effect.
Installing Communicator with PC1616/1832/1864 Panel
NOTE: Before installing Communicator or inserting/removing SIM, ensure that system power is
OFF and telephone line is disconnected.
1. To assemble supplied mounting bracket, perform the following: (See Figure 1 ).
a. Remove the 4 white plastic
standoffs from the bag pro-
vided with the Communica-
tor kit.
b. Insert the 4 standoffs through
the back of the mounting
bracket, into the holes at each
corner. (The antenna mount-
ing tab should be facing away
from you).
c. Place the bracket on a flat,
solid surface. Hold the Com-
municator component side up
and orient the 4 holes on the
Communicator with the 4
standoffs protruding from the
bracket. Push the Communi-
cator firmly and evenly onto the standoffs until it is securely attached to the mounting
bracket.
d. Remove the panel front cover.
e. Remove and discard the circular knockout located in the top-right section of the panel. (This
hole will be used for connection of the supplied radio antenna).
f. Connect the supplied 5” (12.7 cm) antenna cable to the radio, by passing the connector
through the hole on back of the mounting bracket to the communicator board. Push the
antenna connector firmly into the socket on the cellular radio. (See Figure 3).
2. Install the Communicator into the panel:
a. Attach one end of the PC-LINK cable to the panel PC-LINK header on the panel (red wire
goes on Pin 1 of the panel PC-LINK header).
b. Insert the assembled Communicator into the panel.
NOTE: Ensure that the threaded antenna connection point is visible through the knockout hole at
the top right of the panel.
c. Place the nylon washer with bushing (thick flat washer) onto the threaded section of the
antenna cable. Insert the threaded section through the antenna mounting knockout hole at top
right of panel.
INSTALLING CELLULAR/ETHERNET COMMUNICATOR IN
PANEL
DG0009744
Brass Washer
Nylon washer (flat)
Nylon Washer
with bushing
(thicker flat washer)
Brass nut
Antenna
Mounting Tab
Mounting
Holes
Mounting Holes
Antenna
Cable
Mounting Plate
External Antenna
Screw Thread
Communicator
Board
Mounting
Plate
Stand Off
Figure 1: Communicator Mounting Bracke
t

6
Installing Cellular/Ethernet Communicator in 3G Alarm Communicator Installation Manual
d. Place the second nylon washer (flat), followed by the brass washer and the brass nut, onto
the threaded section of the cable, outside the panel. Tighten the assembly by hand only.
(Finger tight only- Do not overtighten the antenna assembly).
e. Locate the screw hole on the right side wall of the
panel. See Figure 2 (screw). Line up the assem-
bled Communicator with the right side wall of the
panel and, using the screw provided, secure the
mounting bracket to the panel.
f. Attach the other end of the PC-LINK cable to the
Communicator (black wire goes on Pin 1 of the
Communicator).
g. Using light pressure (finger tight only), attach the
supplied white quad band whip antenna to the
threaded antenna connection point at top of the
panel.
WARNING! - 3G2060/TL2603G/TL260 modules are
power limited. Do not route any wiring over the
circuit board. Maintain at least 1in. (25.4mm) sepa-
ration between circuit board and wiring. A mini-
mum of ¼ in. (7mm) separation must be
maintained at all points between non-power lim-
ited wiring and power limited wiring.
3. To electrically connect the Communicator to the panel, perform the following steps
(See Figure 3).
a. Disconnect both AC power and battery connections from the panel, and disconnect tele-
phone line.
Module Power Connection
b. Attach a wire from the Communicator’s left PWR terminal to the panel’s BELL+ terminal.
c. Attach a wire from the Communicator’s GND terminal (beside PWR) to the panel’s AUX -
terminal.
d. Attach a wire from the Communicator’s SHLD terminal to the panel’s EGND terminal.
(Protective earth ground).
(Optional) External Bell/Siren Connection
e. Attach a wire from the Communicator’s right PWR terminal to the positive (+) terminal on
the Bell/Siren.
f. Attach the panel’s BELL
- terminal to the negative ( - ) terminal on the Bell/Siren.
NOTE: If an external Bell/Siren is not used, install the 1K½W 5% resistor (Brown, Black, Red,
Gold) (supplied with the panel) between the panel’s Bell + and Bell
- terminals, then only wire
the BELL + to the PWR terminal on the Communicator.
g. Confirm that the SIM card is inserted in the holder and locked.
DG009545
PC-Link
Cable Connector
(screw)
Quad band
Whip Antenna
PC1616/1832/1864
GSM Radio
RJ-45
UA585
Use light pressure
to attach antenna
Finger Tight only.
Figure 2:PC1616/1832/1864 Control Panel

7
Installing Cellular/Ethernet Communicator in 3G Alarm Communicator Installation Manual
Keybus Connection
4. Install the Keybus cable between Communicator and Panel as follows:
WARNING: DO NOT CONNECT KEYBUS RED OR BLK WIRES TO THE PANEL OR
THE COMMUNICATOR TERMINAL BLOCKS.
a. Attach a wire from the Communicator YEL terminal to the panel YEL terminal.
b. Attach a wire from the Communicator GRN terminal to the panel GRN terminal.
Install Network Cable (TL2603G/TL260 only)
5. Route the CAT 5 Ethernet cable through back of the panel and plug it into the Communicator’s
RJ45 jack.
NOTE: Before leaving the premises the Ethernet communication lines must first be connected to
an approved (acceptable to local authorities) type NID. All wiring shall be performed according to
the local electrical codes.
6. Perform the following steps for initial power on of the panel with Communicator installed:
a. Reconnect the AC power, telephone line, and battery +connector to the panel.
(The Communicator and Panel will power up together).
b. Observe that the Communicator’s red and yellow LEDs are flashing together while it initial-
izes. The red and yellow LEDs will continue to flash until the Communicator has success-
fully communicated to all programmed receivers.
NOTE: Initialization may take several minutes to complete. red and yellow LEDs will flash
together during initialization. Do not continue to next step until the red and yellow LEDs have
stopped flashing. (If only the yellow LED is flashing, there is a Communicator trouble and the
Green LEDs are not valid for Communicator Placement Test). Correct trouble indicated by flashes
on yellow LED before continuing. (See Table 9 for troubleshooting assistance).
7. Perform the Communicator Placement Test below.
8. Mount the Panel in final location indicated by placement test.
F
igure 3:Communicator Wiring Diagram
AUDIO/DEFAULT
DSC
UA601
PC-LINK
PC-LINK
COM
TL2603G(R)
TL260(R)
3G2060(R)
AC
AC
Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8
AUX+
BELL +
PGM1 PGM3
RING T-1
PC1616/1832/1864
3G Radio
+
-
UA503
1
To external antenna
Input Ratings from Bell +:
+11.1V ~ +12.6 VDC
100mA standby; 400mA alarm
DSC Panel min. power requirements:
- 16 VAC 40 VA transformer;
- 12 VDC 7Ah battery
+
-
External Bell/Siren
Black
Black
Jumper pins 4 and 5
to reset.
L
o
c
k
1
GRN
(not used)
From NID
TL2603G(R)
Use only CAT5
Supervised
RJ-45
YEL
COM
PWR
GRN YEL
TIP R-1
BLK
RED AUX -
BELL - EGND
Do NOT
connect
Red or Black
Keybus wires!
TX+
GND
TX-
RX+ RX-
SHLD
Green
Yellow
SIM
Network Link
YELLOW
XX
PGM2 PGM4
Maximum cable length
100 m (328 ft)
PWR

8
Communicator Placement Test 3G Alarm Communicator Installation Manual
3G2060 and TL2603G only
To confirm that the cellular antenna location is suitable for radio operation, perform the placement
test as follows:
NOTE: You may need to relocate the Panel or install an optional extension antenna during this
procedure, if radio signal strength is too low.
1. Confirm that the yellow LED on the Communicator is not flashing. A flashing yellow LED indi-
cates trouble on the Communicator. See Table 7 to troubleshoot and correct the cause of this
trouble before continuing to the next step.
2. Observe the strength of the radio signal on the yellow LED and the 2 green LEDs on the Com-
municator meet or exceed the minimum signal level requirement. Minimum Signal Level: The
yellow LED is OFF and the Green LED 1 (furthest from the yellow LED) is ON. (i.e., not
flashing) for the panel location to be acceptable. See table for “Radio Signal Strength” on
page 12 for interpretation of receiver signal strength on LEDs.
NOTE: If the required signal strength is too low with the panel in its current location, the panel
must be relocated or an external antenna is required.
a. If required, the following cellular extension antenna kits are available to the installer:
• GS-15ANTQ - 4.57m (15’) Internal Antenna Extension Kit (Suitable for interior mounting only).
• GS-25ANTQ - 7.62m (25’) External Antenna Extension Kit (Suitable for exterior mounting only).
• GS-50ANTQ - 15.24m (50’)External Antenna Extension Kit (Suitable for exterior mounting only).
Specific instructions for the installation of the extension antenna are included with the kit. Observe
all the electrical safety instructions regarding the installation of the antenna. All the wiring of the
equipment shall be fully compliant with the local rules and regulations.
3. If required, install the antenna extension and perform the following steps to determine the best
location for placement of the antenna :
a. Disconnect the white whip antenna from the panel.
b. Attach one end of the antenna extension cable to the threaded antenna connector on the
panel and the other end to the external antenna.
4. Move the extension antenna to various locations while observing the two Green LEDs on the
panel.
a. Continue to reposition the extension antenna until you receive an acceptable (minimum one
green LED ON solid) signal strength.
NOTE: Minimum strength is: green LED 1 flashing and yellow LED OFF. If green LED 1
is flashing, relocation should be considered.
b. Mount the supplied antenna extension bracket at the location that provides the best signal
strength.
5. Alternately, you can reposition the Panel to improve signal strength. Dismount the panel and
move it to another location to achieve the required signal strength. If the Panel is relocated to
improve signal strength, mount it in the new location.
6. When final Panel/antenna location is determined, continue at the Initial Panel Programming-
section.
Keypad Data Display
Programming locations are accessible via the keypad or DLS 5.
•Section-Toggle Options: The number is displayed when Toggle is ON, the number is not dis-
played when Toggle is OFF. (e.g., Toggle Options displays: [
-- 3 -- 6 -- ]. Options 3and 6are
ON, all others are OFF). Pressing keys 1 through 8 will alternately turn the Toggle ON and
OFF.
•HEX/Decimal Data: Values that are provided with two defaults, separated by a “/” character,
use the format: hexadecimal followed by decimal equivalent (e.g., Default [0BF5/3061]).
COMMUNICATOR PLACEMENT TEST
INITIAL PANEL PROGRAMMING

9
Initial Panel Programming 3G Alarm Communicator Installation Manual
Hexadecimal numbers are shown, with all leading zeroes, to the full field length defined for the
number.
Entering HEX values at keypad
To enter HEX values at the keypad, you must press the *key before entering the HEX value. (e.g.,
to enter “C” at the keypad, press [*][3].
Entering ASCII Characters at keypad
1. Press [*] and use scroll buttons [<] [>] to display “ASCII Entry” on the LCD screen.
2. Press [*] to select ASCII entry mode.
3. Use the [<] [>] scroll keys to display the character you want and press [*] to save and exit
ASCII.
4. Repeat the steps above to enter another ASCII character.
PC1616/1832/1864 Initial Programming
Perform the following steps to ensure that the Communicator and the Panel work together as
intended.
These Sections must be programmed at the panel keypad. Enter [*][8][Installer Code][Section
Number]. Record any values that are modified from their default, in the appropriate Worksheets
for the Panel or Communicator.
1. In Panel Section [167] program 060 (seconds).
2. In Panel Section [382] set Option [5] ON
NOTE: If this option is OFF, the yellow status LED on the Communicator will indicate ‘Panel
Supervision Trouble’ (2 flashes) and the unit can not be programmed via the PC-LINK cable.
NOTE: Account Number in Communicator Section [851][021] automatically syncs with Panel
Section [310] for Panel Versions 4.50 or newer
3. A valid Account Number must be entered in Communicator Section [851][021]. See Program-
ming Section.
NOTE: DSC recommends using the same Account Number for Panel and Communicator.
4. In Panel Sections [301], [302], and [303], program the central station telephone number that
will be used for the cellular/Ethernet Communicator. Valid entries are:
a. A valid telephone number; signals will be routed to the central station using the PSTN.
b. DCAA (Receiver 0); signals will be routed to cellular/Ethernet Receivers 1 - 4 depending on
programming Toggle Options in Communicator Section [851][006].
c. Panel Section [301] sets the Primary communication path, and may be configured as either
PSTN or Communicator routing. Panel Section [302] is redundant, and Panel Section [303]
is the backup telephone number for Panel Section [301]. Refer to the Panel manual for addi-
tional information.
NOTE: The leading digit ‘D’ (dial tone detection) in the telephone number is pre-programmed.
5. In Panel Section [350], program the communication format as: CID (03) or SIA FSK (04).
6. In Panel Sections [351] - [376], program the Communicator call direction options. Refer to the
Panel Installation Manual for details on setting these options.
7. In Panel Section [401] set Toggle Option [2] ‘User Enable DLS’ to ON in order to perform
panel DLS session through cellular or Ethernet.
NOTE: Before leaving the premises, the installer should verify all programmed communications
paths. See Programming Options Section [851][901] to send immediate test transmissions.
NOTE: Sending Test Transmissions to Receivers that are Not Programmed will generate FTC
Trouble.
Communicator Troubles displayed on a PC1616/1832/1864
The General System trouble is the only trouble that will appear on the keypad Liquid Crystal Dis-
play (LCD) when encountered by a Communicator installed in a PC1616/1832/1864. For more
information about the trouble on the Communicator module refer to the panel event buffer. Log
entry will show Fault or Restore for each of the following events:

10
Communicator Status Leds 3G Alarm Communicator Installation Manual
•T-LINK Network Fault/Restore: This log will occur for the following trouble conditions:
SIM Lock Trouble, cellular Trouble, Ethernet Trouble, or Connect24 Configuration Trouble.
•T-LINK Receiver Trouble/Restore: This log will occur for the following trouble conditions:
Receiver Not Available Trouble, Receiver Supervision Trouble, or Failure to Communicate
(FTC) Trouble.
•T-LINK Comm. Fault/Restore: This log will occur when the panel loses communications
with the Communicator and will clear when communications is restored.
The Communicator has 4 on-board LED indicators. These include 1 yellow trouble LED, 1 red
Network Connection Status LED, and 2 green Signal Strength LEDs. The LED meaning is
described in this Section.
Yellow Trouble LED
This yellow LED will flash to indicate a trouble on the unit. The number of flashes indicates the
type of trouble. See the table below for the coded flashes and the conditions which will activate the
Trouble Status LED.
NOTE: Only the highest priority trouble (2 Flashes is the highest priority trouble) is indicated.
When this trouble is restored, the next highest trouble will indicate, if present. This will continue
until all troubles have been cleared. (yellow LED is not flashing).
The following paragraphs describe the conditions associated with the trouble indicated:
Panel Supervision Trouble (2 Flashes)
This trouble will be indicated when communication between the Communicator module and the
Panel fails. If the module can not communicate with the Panel (e.g., loss of power to the panel) the
Communicator will send the ‘Panel Absent Trouble Event’ message to the central station receiver.
When communication returns, a ‘Panel Absent Restore Event’ is sent by the Communicator to the
central station receiver. The reporting codes are ET001 for Trouble and ER001 for Restore. The
panel absent event always uses the primary receiver account code when communicating to the cen-
tral station.
NOTE: The Panel Supervision Trouble/Restore are internally generated events by the Communi-
cator. Trouble is generated if the Communicator misses 6 Polls. Trouble is restored on receipt of
first Poll from the Panel.
COMMUNICATOR STATUS LEDS
Table 7: Yellow Trouble Status LED
# of
Flashes Trouble # of Flashes Trouble
2 Panel Supervision Trouble 8 Receiver Supervision Trouble
4 SIM Lock Trouble 9 FTC Trouble
5 Cellular Trouble 11 Remote Programming
6 Ethernet Trouble 12 Module Configuration Trouble
7 Receiver Not Available Trouble

11
Communicator Status Leds 3G Alarm Communicator Installation Manual
SIM Lock Trouble (4 Flashes) (3G2060(R)/Tl2603G(R) only)
This trouble will signify that the SIM lock feature has been enabled and the unit has not been pro-
grammed with the correct PIN for the SIM card.
Cellular Trouble (5 Flashes) (3G2060(R)/Tl2603G(R) only)
This trouble is indicated for any of the following 4 conditions:
1. Radio Failure: Trouble is indicated after 8 failed attempts to communicate with the cellular
radio.
2. SIM Failure: Trouble is indicated after 10 failed attempts to communicate with the SIM.
3. Cellular Network Trouble: Trouble is indicated for loss of the registration to the network pro-
vider.
4. Insufficient Signal Strength: Trouble is indicated if calculated average signal strength is too
low. (Both green LEDs are OFF). Trouble will clear when the calculated average signal
strength is above minimum (i.e., > CSQ 5).
NOTE: If Option [851][006] Bit 8 is Off, CSQ ≥4 will not trigger Cellular Trouble
Ethernet Trouble (6 Flashes)
This trouble is indicated when Ethernet link between the transmitter and the local switch or router
is absent. This trouble will also be indicated if the unit fails to get Dynamic Host Control Protocol
(DHCP) settings from the DHCP server. (Not active if Ethernet Receivers are not programmed).
Receiver Not Available (7 Flashes)
This trouble is indicated if the unit is not able to successfully initialize with any of the pro-
grammed receivers. Un-programmed receivers are excluded. This trouble is also indicated if the
cellular receiver APNs have not been programmed in Sections [205] and [215].
Receiver Supervision Trouble (8 Flashes)
This trouble is indicated when receiver supervision is enabled and communication between the
Communicator module and the receiver fails. Trouble is indicated if Ethernet 1 and/or Cellular 1 is
supervised and does not receive a heartbeat from the receiver or if cellular is supervised and the
unit does not receive an acknowledgment to 4 heartbeats sent to the receiver.
FTC Trouble (9 Flashes)
This trouble is indicated when the unit fails to communicate module events to the central station.
Trouble is displayed after the unit has exhausted all communications attempts to all programmed
receivers for events generated by the Communicator.
Remote Programming (11 Flashes)
This trouble indicates that a remote firmware update is in progress over the cellular/Ethernet net-
work. The Trouble will clear automatically when the update is completed successfully.
Module Configuration Trouble (12 Flashes)
This trouble is indicated when the System Account Code or the Receiver Account have not been
programmed. Disabled receivers are excluded.
Red Network Connection Status LED
TL2603G/TL260
BLINKING: Indicates communications in progress.
• Once quickly for outgoing Ethernet transmission.
• Twice quickly to indicate incoming Ethernet ACK/NACK.
OFF: This is the normal state of the Red Network Connection Status LED. There are no network
connection issues present.
ON: There is a problem with the Ethernet or the cellular network connection. LED will be ON if
any of the following occur:
• Ethernet cable is not connected,
• DHCP configuration times out,
• Unit fails to get an IP address from the cellular network, or
• Cellular connection has been reset.
(Green LED 1) (Green LED 2) and (Yellow LED) Signal Strength

12
Communicator Reset / Update 3G Alarm Communicator Installation Manual
NOTE: If the yellow LED is flashing, Signal Strength in table below is not valid.
See Table 7 for troubleshooting flashing yellow LED.
NOTE: The communicator will indicate cellular Trouble (yellow LED = 5 flashes) if the calcu-
lated average CSQ Level is 4 or less. The communicator signal strength can be viewed remotely
with Connect24.
Network Activity LEDs (Red and Green)
TL2603G/TL260 only
•Ethernet Activity: Red LED will blink quickly once for Transmit, or twice for Receive.
•Cellular Activity: Green LED 2 will blink quickly once for Transmit, or twice for Receive
Factory Defaults Reset
You can reset the programming options for the Communicator to the factory settings by installing
the hardware jumper. Perform the following steps to reset the Communicator:
NOTE: A jumper is required on AUDIO/DEFAULT pins 4 and 5 to reset the hardware values.
1. Remove panel front cover.
2. Locate the AUDIO/DEFAULT 5 pin connector on the communicator board (see Figure 3).
3. Apply a jumper to short the hardware default pins 4 and 5.
4. Remove AC and DC power from the panel and then reapply power to the Panel. Wait until the
two green LEDs on the communicator begin flashing rapidly.
5. Remove the jumper from the hardware default pins 4 and 5 (Green LEDs will stop flashing).
6. Replace the panel cover.
NOTE: The communicator has now been reset to the factory default values.
Firmware Update
The firmware of the device can be updated over cellular or Ethernet (Remote or Local updating):
• When the firmware update begins, all 4 LEDs are ON.
• During the firmware update process, the LEDs will be cycled individually in a chaser pattern.
• During the firmware update process, Chaser pattern will briefly pause, and resume again. This
indicates Firmware Verification check has passed, and Application Update will begin.
• After a successful update, the unit will automatically restart.
• Should the update fail, all 4 LEDs will flash ON, then OFF together at 1 second intervals.
NOTE: If the firmware update fails, restart the Communicator by cycling Power. For persistent
update failures, contact your dealer.
Table 8: Radio Signal Strength
Signal
Strength
CSQ
Level
Yellow
LED
Green
Led 2
Green
LED 1
Signal
Level dBm Action Required
No Signal 0 ON OFF OFF -108.8
Check all antenna connections.
Confirm cellular service is active in area.
Relocate Panel or install external antenna.
1 Bar 1 - 4 ON
See Note OFF Flashing -108 ~ -103 Relocate Panel or install external antenna if Yel-
low Trouble LED has:
5 flashes.
2 Bars 5 - 6 OFF OFF Flashing -102 ~ -99
3 Bars 7 - 10 OFF OFF ON -98 ~ -91
Location is OK. Cellular signal strength is greater
than CSQ 7.
4 Bars 11-13 OFF Flashing ON -90 ~ -85
5 Bars 14 + OFF ON ON -84 and
higher
COMMUNICATOR RESET / UPDATE

13
Communicator Troubleshooting 3G Alarm Communicator Installation Manual
COMMUNICATOR TROUBLESHOOTING
NOTE: For additional details:
• Refer to Section [983] for troubleshooting the firmware updates
• Refer to Section [984] to verify the trouble status
• Refer to Section [985] for troubleshooting Connect24 programming
Table 9: Trouble LED indications
Trouble
indication
Possible
Causes Trouble Possible Solution
No Indication No Power
• Check the power connections between the Panel and the Communicator.
• Confirm PC-LINK cable is properly installed between communicator and panel.
Yellow LED –
ON Solid
Insufficient
Signal Strength
• Confirm that cellular network service is active in your area.
• Ensure the antenna is securely connected to the radio. Check antenna stub cable is securely
connected to the radio.
• If an external antenna is used ensure the antenna is securely screwed on to the antenna
cable connector. Check external antenna for damage or open/short.
Trouble LED –
2 Flashes
Panel
Supervision
Trouble
• Check Section [382]Toggle Option[5] is ON.(cellular/Ethernet Module Enabled)
• Ensure the PC-LINK cable between the Panel and Communicator is connected properly
(not reversed) and is securely in place.
Yellow LED -
4 Flashes
Lockout
Trouble
• The SIM card has incorrect PIN programmed or has a PIN that the module does not recog-
nize. Replace the SIM card.
Yellow LED –
5 Flashes Cellular Trouble
• Confirm that cellular service is available and active in your area.
• Check all antenna connections.
• Ensure average radio signal strength is CSQ 5or higher. (See Table 8 ).
• Ensure the SIM card is properly inserted into the SIM card holder.
• Ensure the SIM card has been activated. (Could take up to 24 hrs after install).
• If this trouble persists, you must relocate the Panel (and Communicator) or install an exter-
nal antenna extension kit.
Yellow LED –
6 Flashes
Ethernet
Trouble
• Check with your ISP to confirm Internet service is active in your area.
• Ensure your Ethernet cable is securely inserted into the RJ45 jack of the Communicator
and the Hub/Router/ Switch.
• Check the link light on the Hub/Router/ Switch is ON . If link light is OFF, try restarting
the Hub/Router/ Switch.
• If DHCP is used, ensure that the unit has an assigned IP address from the server. In Section
[851] [992] verify a valid IP address is programmed. If not, contact the Network adminis-
trator.
• If problem persists, replace the Ethernet cable and RJ45 connector.
Yellow LED –
7 Flashes
Receiver Not
Available
• Ensure that the Ethernet path has internet connectivity.
• If you are using a static IP address make sure the gateway and subnet mask are entered cor-
rectly.
• If the network has a firewall, ensure the network has the programmed
outgoing ports open (Default UDP Port 3060 and Port 3065).
• Ensure that all the receivers are programmed for DHCP or have the proper IP address and
port number.
• Ensure the cellular receiver APNs have been programmed with the Access Point Name
provided by your cellular provider.
Yellow LED –
8 Flashes
Receiver
Supervision
Trouble
• This trouble is indicated when supervision is enabled and the unit is not able to success-
fully communicate with the receiver.
• If this trouble persists, contact your central station.
Yellow LED -
9 Flashes FTC Trouble
• The unit has exhausted all communications attempts to all programmed receiver for events
generated by the Communicator.
• Restart the system, if trouble persists, contact your dealer.
Yellow LED –
11 Flashes
Remote
Programming
• The LEDs will flash when a remote firmware upgrade is in progress over Ethernet or cellu-
lar. The LEDs will extinguish when update is complete.
Yellow LED –
12 Flashes
Module
Configuration
Trouble
• This indication appears when Section [021] System Account Code or
Section [101]; [111]; [201]; and [211] Receiver Account Code have not been programmed.
Ensure that a valid account code has been entered in these Sections.
All LEDs flash-
ing together
Boot Loader
Failed
• Disconnect power, then reconnect power to the Communicator module.
Red and Yellow
LEDs flashing
together
Initialization
Sequence
• The unit is still initializing please wait while the unit gets its programming and establishes
a connection to all programmed receivers.
Note: This process may take several minutes to complete.
Only Green
LEDs flashing
Hardware
Default Jumper
• The hardware default jumper is installed and must be removed. See Figure 3.

14
Ethernet/Cellular Programming Options 3G Alarm Communicator Installation Manual
The Programming Sections described in this document can be viewed at the keypad LCD. To start
programming enter: [*][8][installer code] [851][###], Where ### isthe 3 digit section number
referenced in this section. The Programming Worksheets at the end of this document can be used
to record the new values when programming changes have been made from the default values.
Programming Sections are accessed through the keypad or DLS 5.
NOTE: The Keypad is unable to view any sections that uses ASCII Characters.
System Options
[001] Ethernet IP Address
Default (000.000.000.000)
Enter the IP address of the Communicator. Ensure that the IP address is unique to your Communi-
cator on the local network. Format is 4 fields, each field is a 3 digit decimal number. Valid range:
000-255. If an IP address is programmed in this Section, the unit will operate with Static IP
(DHCP disabled). Sections [002] and [003] must also be programmed when using Static IP
addresses.
NOTE: Default for this Section is Dynamic Host Configuration Protocol (DHCP) enabled. When
enabled, the DHCP Server will set values for: IP Address [001], Subnet Mask [002], and Gateway
[003]. Programming an IP address in this Section will disable DHCP (Static IP).
[002] Ethernet IP Subnet Mask
Default (255.255.255.000)
Enter the Ethernet IP Subnet Mask of the Communicator. Format is 4 fields, each field is 3 digits.
Valid range: 000-255.
NOTE: If DHCP is enabled, the DHCP Server will assign the subnet mask for this Section and the
programmed value will be ignored.
[003] Ethernet Gateway IP Address
Default (000.000.000.000)
Enter the Ethernet Gateway IP address of the Communicator. The gateway IP address is required
when a router is used on the local network to reach the destination IP address specified in Section
[001]. Format is 4 fields, each field is a 3 digit decimal number. Valid range: 000-255.
NOTE: If DHCP is enabled, the DHCP Server will assign the Gateway IP address for this Section
and the programmed value will be ignored.
[004] Receiver Supervision Interval
Default (0087/135)
When receiver supervision is enabled (ON) in Section [005] Toggle Option [3], the unit sends
heartbeats to Ethernet Receiver 1 or Cellular Receiver 1 to test the communications path. Use this
Section to set the interval time (in seconds) when heartbeats will be sent to the receivers. Valid
range 000A-FFFF seconds. If the programmed value is less than (000A/10) seconds, supervision is
disabled.
[005] System Toggle Options
[1] Ethernet Receiver 1 Supervised
Default (OFF)
TL2603G/TL260 only
ON: Ethernet Receiver 1 will be supervised and heartbeats will be sent to Ethernet Receiver 1 based on
the supervision interval programmed in Section [004].
OFF: Ethernet Receiver 1 will not be supervised. When disabled, heartbeat 1 is sent to the Ethernet
receiver once every hour, regardless of supervision type (heartbeat 1 or 2). The heartbeat is resent every
5 seconds until ACK. If no event or heartbeat ACK is received after (Receiver Supervision Interval + 75
seconds), Supervisory trouble is indicated.
NOTE: Ethernet Receiver 2 can not be supervised.
ETHERNET/CELLULAR PROGRAMMING OPTIONS

15
Ethernet/Cellular Programming Options 3G Alarm Communicator Installation Manual
[2] Cellular Receiver 1 Supervised
Default (OFF)
ON: Cellular Receiver 1 will be supervised and heartbeats will be sent to Cellular Receiver 1 based on
the supervision interval programmed in Section [004]. If ACK to heartbeat is not received, it is retrans-
mitted every 5 seconds. Failure to ACK 2 consecutive heartbeats will reset the radio.
OFF: Cellular Receiver 1 will not be supervised. When disabled, heartbeat is not sent to the receiver.
Supervisory trouble is indicated.
NOTE: Cellular Receiver 2 can not be supervised.
[3] Supervision Type
Default (OFF)
ON: Heartbeat 1 (Commercial Supervision). This supervision type is suitable for applications where
swap detection is required on the supervisory packet.
OFF: Heartbeat 2 (Residential Supervision). This supervision type is suitable for applications where
supervision of the communication path to the receiver is required. (no swap detection).
NOTE: Commercial supervision is more data intensive than residential supervision and should
only be used when required to meet the approval for the installation.
[4] Primary Path
Default (OFF - TL2603G/TL260) (ON - 3G2060)
ON: Cellular channel is the primary path. Ethernet channel is the secondary path, if it exists.
OFF: Ethernet channel is the primary path in a dual Communicator. Cellular channel is the second-
ary path.
[5] Redundant Communications
ON: Events will be communicated to Ethernet Receiver 1 and Cellular Receiver 1 at the same
time. Events will be communicated to Ethernet Receiver 2 and Cellular Receiver 2 at the same
time. As long as the event is successfully communicated to 1 of the 2 paths (Ethernet or Cellular)
the Communicator will move on to the next event.
NOTE: Do not configure Ethernet Receiver 1 and Cellular Receiver 1 to communicate using a
common receiver configuration (i.e., identical Receiver IP address and Receiver Remote Port).
OFF: Events will be communicated to the receivers individually.Toggle should be OFF when guar-
anteed message delivery to both receivers is required.
[6] Remote Firmware Upgrade
Default (ON)
ON: The Communicator module firmware can be remotely upgraded using the Ethernet/Cellular paths.
OFF: The Communicator module firmware can not be remotely upgraded. Local firmware upgrade is
still possible.
[7] Alternate Test Transmissions
Default (OFF).
ON: When the periodic test transmission interval occurs, the test transmission will alternate between
being sent to the primary and secondary receivers with each test transmission interval.
OFF: When the periodic test transmission interval occurs, the test transmission will be sent to the pro-
grammed receivers, based on the settings of the periodic test transmission reporting codes.
[8] Cellular Low Signal Trouble.
Default (OFF)
This option masks the Low Signal trouble from generating Cellular trouble.
ON: A Cellular Trouble event is generated when the radio signal level falls below threshold level (aver-
age CSQ level is 4 or less).
OFF: A Cellular Trouble event is not generated when the radio signal level falls below threshold level
(average CSQ level is 4 or less).
[006] System Toggle Options 2
[1] Ethernet 1 Receiver Enabled.
Default (ON) (OFF for 3G2060).
ON: Ethernet Receiver 1 is enabled.
OFF: Ethernet Receiver 1 is disabled.

16
Ethernet/Cellular Programming Options 3G Alarm Communicator Installation Manual
[2] Ethernet 2 Receiver Enabled.
Default (ON) (OFF for 3G2060).
ON: Ethernet Receiver 2 is enabled.
OFF: Ethernet Receiver 2 is disabled.
[3] Reserved. ( ).
[4] Cellular 1 Receiver Enabled.
Default (ON).(OFF for TL2603G/TL260)
ON: Cellular Receiver 1 is enabled.
OFF: Cellular Receiver 1 is disabled.
[5] Cellular 2 Receiver Enabled.
Default (ON).(OFF for TL2603G/TL260)
ON: Cellular Receiver 2 is enabled.
OFF: Cellular Receiver 2 is disabled.
[6] Reserved ( ).
[7] DLS Over Cellular.
Default (ON).
NOTE: Program this toggle as OFF if you want to completely disable DLS from using the Cellu-
lar path.
ON: DLS is enabled on the Cellular path.
OFF: DLS is disabled on the Cellular path.
NOTE: If this Toggle is OFF, DLS sessions will occur on the Ethernet path only, regardless of Pri-
mary Path set in Section [005] Toggle Option [4]. If it is ON then the Communicator will connect
to the Primary path first for DLS and if the session fails, the Secondary path will be used.
[8] Reserved ( ).
[007] DNS Server IP 1
Default (000.000.000.000)
Enter the IP address for DNS Server 1. Format is 4 fields, each field is a 3 digit decimal. Valid
range: 000-255.
NOTE: If no value is programmed and DHCP is used, the DHCP Server will configure the
address. If an address is programmed and DHCP is used, the address that you program will be
used instead of the DHCP address.
[008] DNS Server IP 2
Default (000.000.000.000)
Enter the IP address for DNS Server 2. Format is 4 fields, each field is a 3 digit decimal. Valid
range: 000-255.
NOTE: If no value is programmed and DHCP is used, the DHCP Server will assign this value. If
an address is programmed and DHCP is used, the address that you program will be used instead of
the DHCP address.
Programming Options
[011] Installer Code
Default (CAFE)
Program your installer code for this Communicator module. The installer code will be required
when programming the Communicator module. Valid range: 0000 - FFFF.
[012] DLS Incoming Port
Default (0BF6/3062)
The DLS Incoming Local Port (listening port) is the port DLS IV will use when connecting to the
Communicator. If a router or gateway is used, it must be programmed with a Transmission Control
Protocol (TCP) port forward for this port to the Communicator module IP address. Valid range:
0000 - FFFF.