Dungs VisionBox User manual

MF … 26
M • Edition 07.20 • Nr. 270 173
1 … 26
The VisionBox allours the setting of the parameter values of
DUNGS control devices via PC, Laptop or Tablet PC
(from WIN 10, with USB connection).
Suitable for:
MPA 4xxx
MPA 51xx
VPM
W-FM25
GB
Description
DUNGS VisionBox
2. Warnings
Never carry out work as long as gas
pressure or voltage is applied. Avoid
open re. Please observe public regu-
lations.
The device must be protected from
vibrations and mechanical impacts.
All adjustments and settings should
only be performed in accordance with
the instruction manuals of the con-
nected machines.
The recognised occupational safety
rules and accident prevention regula-
tions must be observed and, if neces-
sary, personal protective measures
must be taken.
The device may only be operated in
compliance with the operating condi-
tions stated on the type plate.
Prior to assembly, the device must be
inspected for transport damage.
The device must not be used in areas
with increased seismic risk
Protection from environmental im-
pacts and weather conditions (corro-
sion, rain, snow, icing, humidity (e.g.
by condensation), mould, UV radiation,
harmful insects, poisonous, corrosive
solutions/liquids (e.g. cutting and
cooling uids), must be guaranteed.
Depending on the installation site, it
may be necessary to take protective
measures.
The device must not be exposed to
open re. Protection against lightning
strikes must be guaranteed.
2.1 General warnings
Application
Explanation of the symbols
1, 2, 3,... = Order of
action
• = Instruction
Suitable operating systems:
WIN XP, 7, 8, 8.1, 10
Note: Passwords are required to install the software and
for parameterization of the systems.
Please contact your DUNGS sales representative for the
passwords your require.

2 … 26
M • Edition 07.20 • Nr. 270 173
2.2 Designated use
The device is used in accordance with its designated use
if the following instructions are observed:
• Applicable only with suitable DUNGS systems and
software
• Use only in compliance with the operating conditions
stated on the type plate.
2.3 Risks in case of misuse
• If used in accordance with their designated use, the
devices are safe to operate.
• Non-observance of the regulations may result in per-
sonal injury or material damage, nancial damage or
environmental damage.
3. Approval / declaration of conformity
• Operator errors or misuse present risks to life and
limb of the operators and also to the device and other
material property.
• Use in perfect condition only.
• Malfunctions and faults must be eliminated immedi-
ately.
• Use only in observance of the instructions given in this
instruction manual and of national regulations.

2 … 26
M • Edition 07.20 • Nr. 270 173
3 … 26
4. Table of contents
1. Target group 1
2. Warnings 1
2.1 General warnings 1
2.2 Designated use 2
2.3 Risks in case of misuse 2
3. Approval/declaration of conformity 2
4. Table of contents 3
5. Inhalt VisionBox mini 4
6. Software Download and Installation 6-9
7. Connection VisionBox 10
8. Operation VisionBox Software 11-13
8.1 Change of access level 14-15
8.2 Copy of a existing parameter set 15
8.3 Change of parameter 16-17
9. Error overview 18
10. VisionBox Update Software 19
11. VisionBox Update error messages 19-20
12. Documentation device conguration 21-22
13. Send device conguration via email 23
14. Reset to factory setting 24

4 … 26
M • Edition 07.20 • Nr. 270 173
The VisionBox mini includes the adapter to connect a
PC/Laptop to MPA and VPM systems.
The required software is not included. It is available from
the download ares in the DUNGS homepage
www.dungs.com/softwaretools
5. Content VisionBox mini
Connecting cable PC/VisionBox
VisionBox
Connecting cable VisionBox/TWI connection
MPA, VPM

4 … 26
M • Edition 07.20 • Nr. 270 173
5 … 26
6. Software Download and Installation
www.dungs.com/softwaretools
> VisionBox
Installation:
Select a le and select „Open“
Download the le
Run the .exe le

Press „Ausführen“

Choose language during installation

Conrm „Next“

6 … 26
M • Edition 07.20 • Nr. 270 173
6. Software Download and Installation

Enter Password


Conrm target folder „Yes“
Select Start Menu Folder
Conrm with „Next“

Select target folder
Conrm with „Next“

6 … 26
M • Edition 07.20 • Nr. 270 173
7 … 26

Select icon on desktop and / or in quick
start bar
To install the program on a Tablet PC
choose „Tablet mode“
Conrm with “next”

Start installation: „Install“

Please wait, installation continues
6. Software Download and Installation

8 … 26
M • Edition 07.20 • Nr. 270 173



Please conrm „I accept…“, continue
installation “Install”
Please wait, installation continues
Complete Installation „Finish“
6. Software Download and Installation

8 … 26
M • Edition 07.20 • Nr. 270 173
9 … 26
6. Software Download and Installation

Complete installation of the VisionBox pro-
gram „Finish“
Restart the computer to enable the changes

10 … 26
M • Edition 07.20 • Nr. 270 173
7. Connection VisionBox
1. De-energize MPA / VPM.
2.Connect the 4-pin connector of the VisionBox to the ter-
minal „TWI“ - note encoding.
3. Connect the VisionBox to the computer / laptop and
start the PC / Laptop.
LED Power – on
4. Energize MPA / VPM.
LED MPA – on
LED PC – ashing
ATTENTION: Line voltage, don´t touch any live parts.
Mind the safety rules when working with energized elec-
trical components.
LED Power – on
LED MPA – on
LED PC – ashing
5. Start program VisionBox.
6. Connect MPA/VPM to VisionBox Software
7. All LED are permanent on

10 … 26
M • Edition 07.20 • Nr. 270 173
11 … 26



Start-up image VisionBox.
Change language via „Settings GUI“
Link to MPA / VPM via „Connection“ or
symbol „Connector“
ATTENTION: In case of a required
software update for the VisionBox see
chapter 10
Choose link to PC / Laptop and conrm
„OK“
With the VisionBox Mini only USB and
Oine mode possible.
MPA can be equipped with extension
modules.
Please choose the built in module and
conrm with OK.
8. Operation VisionBox Software
Initial screen VisionBox

12 … 26
M • Edition 07.20 • Nr. 270 173


The standard view shows:
Status: Operating condition of the connected controlbox
Error overview: Contend of the error memory of the connected controlbox
Parameter overview: Current parameter setting of the connected controlbox
The windows shown can be displayed or removed via „View“
8. Operation VisionBox Software
Standard View

12 … 26
M • Edition 07.20 • Nr. 270 173
13 … 26

The view „Online-Datalog“ provides a graphical overview
of the burner functions.
8. Operation VisionBox Software
View: Online-Datenlog

14 … 26
M • Edition 07.20 • Nr. 270 173



Adjusting the parameter setting
To adapt or change parameters is done for all DUNGS devices according to the same procedure.
However, the devices dier in the activation of new values.
Please refer to the corresponding operating and installation instructions.
The ability to change parameters is restricted by a password hierarchy:
Password levels
Level 5: Operator / no password / no change authorization
Level 4: Service / password / limited change authorization
Level 3: OEM / Password / full editing rights
Level 2: OEM expert / password / full editing rights incl. expansion variable upper and lower limits
Level 1: DUNGS / password / developer level
Open „Settings MPA“ (also for VPM)
Select „Access Level“
Enter password
Select Access Level
Conrm with OK
8.1 Change of access level

14 … 26
M • Edition 07.20 • Nr. 270 173
15 … 26



Conrm change of the access level by
pressing the RESET button on the MPA /
VPM
Change of the access level successful,
complete with „OK“
Open „Settings MPA“ (also for VPM)
Select „Load conguration“
If the VisionBox program is connected to a
MPA/VPM the dierences between the actual
parameter setting of the MPA/VPM and the
loaded conguration will be shown with yellow
marked cells.
8.2 Copy of a existing parameter set

16 … 26
M • Edition 07.20 • Nr. 270 173
8.3 Change of parameter


Window „Parameter overview“
Example Change prepurge time

16 … 26
M • Edition 07.20 • Nr. 270 173
17 … 26


The value (time in seconds) for the pre-
purge time may be entered direct in the
value window, by using the +/- buttons or
by moving the value pointer.
Conrm value with „OK“
The new value is transferred to the device
The value (number of allowed restart
attempts) may be entered direct in the
value window, by using the +/- buttons or
by moving the value pointer.
Conrm value with „OK“
The new value is transferred to the device.
The values are saved immediately after
the conrmation in the control, to enable
the parameter change refer to the relevant
operating and installation instructions.
Select parameter and activate the parameter by double-
click in the value eld.
Example Changing number of restart attempts
Alternatively, via a selection menu (click right mouse
button) the parameters are enabled for change.

18 … 26
M • Edition 07.20 • Nr. 270 173

The error overview shows the last ten in the control stored
errors.
The error ID refers to the error description in the corre-
sponding operating and installation instructions.
9. Error overview

18 … 26
M • Edition 07.20 • Nr. 270 173
19 … 26
10. VisionBox Update Software


Select „rmware update“ with „OK“
11. VisionBox Update, error messages
If the VisionBox is connected to the PC / laptop via USB
and the software is started, the program automatically
performs a check of the software status of the VisionBox.
Early versions of the VisionBox can not be updated.
The following error message is displayed.
Update VisionBox only possible by DUNGS.
If a later version of the rmware available a update window
automatically opens.

20 … 26
M • Edition 07.20 • Nr. 270 173
11. VisionBox update, error messages
Other errors such as missing link shows a log of the error.

