Eldes ESIM021 User manual

GSM SECURITY AND CONTROL SYSTEM
ESIM021

2
Copyright © “ELDES UAB”, 2010. All rights reserved
It is not allowed to copy and distribute information in this document or pass to a third party without advanced written autho-
rization by“ELDES UAB”. “ELSDES UAB”reserves the right to update or modify this document and/or related products without
a warning. Hereby, ELDES UAB declares that this GSM Alarm and control system ELDES ESIM021 is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted
at www.eldes.lt/ce
Manual v1.1
Safety instructions
Please read and follow these safety guidelines in order to maintain safety of operators and people around:
• AlarmandcontrolsystemESIM021(laterreferencedassystem)hasradiotransceiveroperatingin
GSM850/900/1800/1900 bands.
• Don’tusethesystemwhereitcanbeinterferewithotherdevicesandcauseanypotentialdanger.
• Don’tusethesystemwithmedicaldevices.
• Don’tusethesysteminhazardousenvironment.
• Don’texposethesystemtohighhumidity,chemicalenvironmentormechanicalimpacts.
• Don’tattempttopersonallyrepairthesystem.
• Systemlabelisonthebottomsideofthedevice.
TheWEEE(WasteElectricalandElectronicEquipment)markingonthisproduct(seeright)oritsdocumentationindi-
cates that the product must not be disposed of together with household waste. To prevent possible harm to human
health and/or the environment, the product must be disposed on in an approved and environmentally safe recycling
process. For further information on how to dispose of this product correctly, contact the system supplier, or the local
authority responsible for waste disposal in your area.
System ESIM021 is a device mounted in limited access areas. Any system repairs must be done only by qualied,
safety aware personnel.
The system must be powered by main 9-15V 300mA power supply which must be approved by LST EN 60950-1
standard and be easily accessible.
AnyadditionaldeviceslinkedtothesystemESIM021(computer,sensors,relaysetc.)mustbeapprovedbyLSTEN
60950-1 standard.
ExternalpowersupplymustbereachableandcanbeconnectedtoACmainsonlyinside
installationroomwithautomatic2-polecircuitbreakercapableofdisconnectingcircuit
intheeventofshortcircuitorover-currentcondition.Opencircuitbreakermusthavea
gap between connections of more than 3mm.
Mainspowermustbedisconnectedbeforeanyinstallationortuningworkstarts.Thesysteminstallationormainte-
nance must not be done during stormy conditions.
Thedeviceisswitchedoby2-polecircuitbreaker.
FuseF1type–miniSMDC0,5A.Replacementfuseshavetobeexactlythesameasindicatedbythemanufacturer.
Phase
DC 9-15V
Null
PE
ESIM021

USER MANUAL ELDES ESIM021 V1.1 3
Limited Liability
Thebuyermustagreethatthesystemwillreducetheriskofre,theft,burglaryorotherdangersbutdoesnotguaranteeagainst
such events.
“ELDESUAB”willnottakeanyresponsibilityregardingpersonalorpropertyorrevenuelosswhileusingthesystem.
“ELDESUAB”liabilityaccordingtolocallawsdoesnotexceedvalueofthepurchasedsystem.“ELDESUAB”isnotaliatedwithanyof
the cellular providers therefore is not responsible for the quality of cellular service.
Manufacturer Warranty
The system carries a 24-month warranty by the manufacturer“ELDES UAB”. Warranty period starts from the day the system has been
purchased by the end user. The warranty is valid only if the system has been used as intended, following all guidelines listed in the
manualandwithinspeciedoperatingconditions.Receiptmustbekeptasaproofofpurchasedate.
Thewarrantyisvoidedifthesystemhasbeenexposedtomechanicalimpact,chemicals,highhumidity,uids,corrosiveandhazar-
dous environment or other force majeure factors.
Package content:
1. ELDES ESIM021 ............................................ qty. 1
2. ESIM021 User Manual...... .........................qty. 1
About User Manual
This document describes GSM security and control system ESIM021, it‘s installation and operation. It is very important to read User Manual
before start using the system.
1. General Information
1.1 Function
ESIM021 is a microcontroller based device used to inform users about the alarm in automatic or security systems and control one electric
appliance – open collector.
1.2 Operation description
TheGSMsecurityandcontrolsystemESIM021usestheGSMnetworkfortransmissionofinputs(alarmsgeneratedbyoneofthesystem
zones)toauthorisedusers.Inadditiontobeinginformedabouttriggers/resetsoftheinputs,theuserscanmanagethesystemandusethe
system to control one electronic device.
Thesystemhastwodigitalinputs(normallyopen)calledZone1andZone2.ESIM021canalsocontrol1electronicdevice(usinganopen
collector)onreceiptofthecorrectSMStextmessagefromoneoftheauthorisedusers.Forexample,userscanturnonorotheheating,
lighting, lift the gates, blinds etc.The system remembers the output setting if there is a temporary electricity failure. Once initialised, ESIM021
will function 24/7.
When an authorised number calls to the system, the device answers and the user can listen for 2 minutes to what is going on in the premises.
Thisfunctionworksonlywhenamicrophoneisconnected.Thismicrophonedoesnotincludeintostandardpackagecontent.Thesystem
willignoreSMSrequestsandvoicecallscomingfromunknowntelephonenumbers.Userscanbeinformedabouttriggered/resetinputsby
SMS(seechapter1.2.4)orCALLmethods(seechapter1.2.5).Usersalsocanenableanddisableeitherinput(seechapter2.2).
Anynumberformatcanbeused,forexample[phone],861111111orevenshortnumberslike111.Internationalnumbersmust
beenteredwith„+“or„00“.
1.2.1 Entering users on the SIM card using a mobile phone
The SIM card should be inserted into the phone.The two user numbers must be entered into the SIM card memory under the names“User1”
and“User2”.TheseshouldbeenteredintotheSIMphonebookinyourmobilephone.ItisalsopossibletoenterUser1only.ThentheSIMcard
should be inserted into the ESIM021.
1.2.2 Entering user by phone call to the system
TheSIMcardshouldbeinsertedintotheESIM021.WhenESIM021startsitlooksforUser1andUser2namesintheSIMcardmemory.Ifthe
system can‘t nd any of these users, it waits for a phone call, answers the call and saves the phone number as User1.
NOTE: with this type of setup, only User1 can be entered.

4
1.2.3 Entering users by SMS text message
TheSIMcardshouldbeinsertedintotheESIM021.UserscanenterphonenumbersviathefollowingSMSformat:NRx:yyyyyyyy,where
x-1or2(User1orUser2),yyyyyyyy-userphonenumber.ThismethodcanbeusedtoenterbothUser1andUser2phonenumbers.This
method may be used to change entered users numbers with new ones.
NOTE: this method can be used only from authorized numbers – User1 and/or User2, so if there is no any entered user – this method
willnotwork.
1.2.4 SMS method
Whenadigitalinput(Zone1orZone2)istriggered,theusersareinformedbyanSMSmessagecontainingthetext„TriggeredZONE1“or
„TriggeredZONE2“.Whenthedigitalinputresets,theusersareinformedbyanSMSmessagecontainingthetext„RestoredZONE1“or
„RestoredZONE2“.
1.2.5 CALL method
Whenadigitalinput(Zone1orZone2)istriggered,theusersareinformedbycall.Thedevicewillcallbothusers,rstcallingUser1and
afterwardsUser2.Ifauseranswersthecall,itwilllastfor10secondsandthenthedevicewillhangup.Thisfunctionworksonlywhena
microphoneisconnected.Thismicrophonedoesnotincludeintostandardpackagecontent.
NOTE: WhenusingtheCALLmethoduserswillnotknowwhichinputwastriggeredandalsowillnotbeinformedaboutresetinputs.
1.3 Technical Specications
Electrical and mechanical specications
Supply voltage 9-15V 300mA max
Current used in standby mode 30mAmax
GSM modem frequency 850/900/1800/1900 Mhz
Number of digital inputs (normalopen) 2
Allowable digital input voltage values 0-30V
Impulse duration >600ms
Number of outputs 1
Outputmaximumswitchingratings Current - 500mA, voltage - 30V
Output circuit
Dimensions 108x52x30mm
Operating temperature range -35…+55oC
1 R OUT Open collector output.
Output is pulled to COM
when enabled.
1.4 Connector Functionality
Short explanation of the main units
GSM MODEM GSMnetwork850/900/1800M/1900MHzmodem
SIM CARD SIM card
LED Light-emitting diodes indicator
ANT GSM antena
MIC Microphone
ANT
GSM
MODEM
MIC
SIM CARD
LED
Z2 Z1 DC+ COM OUT
Fig. No. 1

USER MANUAL ELDES ESIM021 V1.1 5
Connector functionality
Labeling Explanation
DC+ DC+powerinconnector
COM Earth pin
OUT Controlledoutput(Opencollector)
Z1 DigitalinputZ1
Z2 DigitalinputZ2
LED indicator status Meaning
OFF Nonetworkconnection
Every 1 sec Notsynchronizedwithnetwork
Every 2 sec Synchronizedwithnetwork
1.5 Connection Circuit
System ESIM021 and security unit COM must be connected.
ESIM021 can be powered from battery. The battery capacity shouldn‘t be higher than 7Ah.
InputsZ1andZ2areconnectedtosecurityunitPGMoutputsifPGMareimplementedasopen
collector circuit or any other circuit and if it commutates with COM.
ItisalsopossibletoconnectZ1andZ2inputsto,forinstance,motionsensororanyothersen-
sor as well as automatics device provided the inputs are commutated with COM.
1.6 System installation
Thesystemboxshouldbexedwithfourscrewstothewall.SincetheESIM021hasintegratedGSMantenna,itshouldnotbe
installedintothemetalbox.Fortheconnectionofpowersupply,outputandinputsconnectorsshouldbeused1thread0,5mm2
cable. Cables should be connected to the connectors and brought through the special cover hole for cables.
1. Enter one or two numbers into SIM card under names“User1” and “User2”.
2. PlaceSIMcardintheholderbutmakesurethatSIMcardPINcoderequestisdisabled(PINcodecanbedisabledbyputtingSIM
cardintomobilephoneandfollowingpropermenus).SIMcardshouldnothaveanyremainingSMSmessages.AllSMStext
messages from SIM card will be automatically deleted during system start.
3. Connect the circuit as shown in Fig. No.2. Power supply cables are connected last. When connecting ESIM021 to security cen-
tral system power supply, usually the security system AUX output is used. Security system power supply must be disconnected
before connecting ESIM021. The system should not be installed on metal surfaces.
4. When DC power supply is used, there is no need to connect any other power supplies.
5. The system will start in less than a minute.
GSM communication and
control system ESIM021
Alarm system or other appliance
PGM1 PGM2
+12V
Z1
Z2 DC COM OUT
Fig. No. 2

6
To increase system reliability, it is recommended not to use prepaid SIM cards. The system would fail to send any mes-
sages upon depletion of prepaid account. Also it is recommended to disable call forwarding and voice mail.
It is worth to choose the same GSM cellular provider as most users use assuring fast and reliable SMS message delivery
and phone call connection.
Even though alarm system ESIM021 installation is not complicated, it is recommended to be performed by a person
withbasicknowledgeinelectricalengineeringandelectronicstoavoidanysystemdamage.
2. System control commands
VERY IMPORTANT!!!
Underscoresymbol‘_’inthismanualisusedtorepresentspace.WhenwritingSMSmessages,everyunderscoresymbol
shouldbereplacedbysinglespacesymbol.Don’tleaveanyspaceatthebeginningandtheendofthemessage.
To manage and congure the device can only entered User1 and User2 phone numbers.
2.1 Change the way system informs about events
By default the system is set to inform users about events via SMS message. To set system to inform
users via calls, user have to send SMS message to Esim021:
TochangebackthesystemtoinformusersviaSMS,userhavetosendSMSmessagetoEsim021:
2.2 Enabling/disabling zones
Enabling Zone
Any zone can be enabled by sending the following SMS message:
Disabling Zone
Any zone can be disabled by sending the following SMS message:
The zones can be enabled/disabled together or separately one by one.
Both zones can be disabled by sending the following SMS message:
CALL
ZONE1:ON or ZONE2:ON
ZONE1:OFF or ZONE2:OFF
ZONE1:OFF_ZONE2:OFF
SMS
ESIM 021
CALL

USER MANUAL ELDES ESIM021 V1.1 7
OUT:ON
OUT:OFF
ESIM 021
ZONE1:OFF
or ZONE2:
OFF
2.3 Managing Output Controller
Alarm system ESIM021 has open-collector controlled output. It can be used to control various electrical devices such as electric
pumps,heating,lighting,etc.Whenoutputsareenabled,itcorrespondstooutputpinsbeingpulledtoground(GND).
Enabling output:
Disabling output:
3. Technical Support
3.1 Technical Support
Indication Possible reason
Indicator is o or not
blinking
· noexternalpowersupply
· circuit not properly connected
· blown fuse
·
System does not send
any SMS messages and/
or does not ring
· SIM card account depleted
· nonetworksignal
· user number is not programmed
Ifyourproblemcouldnotbexedbytheself-guideabove,pleasecontactyourdistributorormanufacturertechsupportby
email[email protected]Moreuptodateinformationaboutyourdeviceandotherproductscanbefoundatthemanufacturer’s
website www.eldes.lt