Enabling Devices Bump & Go Plane User manual

For Technical Support:
For Technical Support:For Technical Support:
For Technical Support:
Call our Technical Service Department
Monday through Friday, 9 a.m. to 5 p.m. (EST
1-800-832-8697
[e-mail]
Bump & Go Plane #1008
USER’S GUIDE
50 Broadway
Hawthorne, NY 10532
Tel. [phone] / Fax [phone]
Toll Free 800.832.8697
www.enablingdevices.com
www.enablingdevices.comwww.enablingdevices.com
www.enablingdevices.com

Spin and Go!
Spin and Go!Spin and Go!
Spin and Go!
Just activate your capability switch and the Bump & Go Airplane will
twirl about when it hits an object and go in another direction. Lights
flash and the engine spins. A fun way to increase visual attention.
Size: 6"L x 6"W x 3½"H. Requires 2 AA Batteries. Weight: ¾ lb.
Operation:
Operation:Operation:
Operation:
1. Bump & Go Plane requires 2 AA Batteries to operate. Alkaline
batteries are recommended because they last longer. Do not use
rechargeable batteries because they supply a lower voltage and
the unit may not perform as well. Never mix old and new batteries
together or different brands or types together.
2. To install the batteries turn Bump & Go Plane over and locate the
small screw on the battery cover door. Using a Phillips head
screwdriver open the compartment and install 2 AA batteries
paying close attention to proper battery polarity.
3. Replace the battery compartment cover and secure with the
screw. Connect to any external capability switch (not included via
the jack located on top of Bump & Go Plane. Bump & Go Plane is
equipped with a 1/8" female mono jack for use with external
capability switches that have a 1/8" mono plug. Make sure you
have a tight connection. There should be no gaps. When using a
switch leave the On/Off switch set to Off.
4. Actuate your capability switch and Bump and Go Airplane will spin
about when it hits an object and go in another direction. Lights will
flash and the engine spins. Bump and Go Airplane can also be
used without the use of an external switch, by turning the built in
On/Off switch to On.
Troubleshooting:
Troubleshooting:Troubleshooting:
Troubleshooting:
Problem:
Problem: Problem:
Problem: Bump & Go Plane does not function correctly.
Action #1:
Action #1: Action #1:
Action #1: Replace the batteries paying close attention to proper
battery polarity.
Action #2:
Action #2:Action #2:
Action #2: Make sure that the connection between the external
capability switch and the jack are TIGHT. There should be NO gaps.
Action #3:
Action #3: Action #3:
Action #3: Try your switch/with another switch operated toy/device in
an effort to rule out your switch as the source of the problem.
Care of Unit:
Care of Unit:Care of Unit:
Care of Unit:
If you will not be using Bump & Go Plane for an extended amount of
time, we recommend removing the batteries.
The Bump & Go Plane can be wiped clean with any mild household
multi-purpose, non-abrasive cleaner and disinfectant. We recommend
Simple Green, which is a non toxic biodegradable all-purpose cleaner.
Do not use abrasive cleaners, as they will scra
Do not use abrasive cleaners, as they will scraDo not use abrasive cleaners, as they will scra
Do not use abrasive cleaners, as they will scratch the surface of
tch the surface of tch the surface of
tch the surface of
the unit.
the unit.the unit.
the unit.
Do not submerge the unit, as it will damage the electrical
Do not submerge the unit, as it will damage the electrical Do not submerge the unit, as it will damage the electrical
Do not submerge the unit, as it will damage the electrical
components.
components.components.
components.
Rev
Rev Rev
Rev 2
22
2/
//
/16
1616
16/
//
/1
11
17
77
7