Evolis Avansia User manual

Service Manual_AVA1_ENG-20220922_I 1
AVANSIA
SERVICE MANUAL

Service Manual_AVA1_ENG-20220922_I 2
TABLE OF CONTENTS
INTRODUCTION................................................................................................................................................................................................. 6
Copyright.......................................................................................................................................................................................................... 6
Copyright notice .......................................................................................................................................................................................... 6
Trademarks ..................................................................................................................................................................................................... 6
Warranty........................................................................................................................................................................................................... 6
Environmental information................................................................................................................................................................... 6
Recycling of end-of-life products ...................................................................................................................................................... 6
Warranty registration............................................................................................................................................................................... 7
Getting started.............................................................................................................................................................................................. 7
Contents ........................................................................................................................................................................................................... 7
Icons.................................................................................................................................................................................................................... 7
Unpacking ....................................................................................................................................................................................................... 8
DESCRIPTION OF THE PRINTER.............................................................................................................................................................. 9
Connecting the printer ............................................................................................................................................................................11
GENERAL OUTLINE.........................................................................................................................................................................................12
Overall Explanation Basic specifications .....................................................................................................................................12
Mechanism components and functions.......................................................................................................................................12
Cassette Handling Good Practices ................................................................................................................................................. 14
Image printing process...........................................................................................................................................................................15
Primary Transfer Feed Roller (Platen Roller) ............................................................................................................ 15
Ink Ribbon............................................................................................................................................................................... 16
Transfer Film.......................................................................................................................................................................... 16
Initial Operation of Ink Ribbon and Transfer Film .................................................................................................. 17
Secondary Transfer Assembly ........................................................................................................................................ 17
Heat Roller .............................................................................................................................................................................. 18
Feeding & Transport process ..............................................................................................................................................................19
USING THE OPERATION PANEL.............................................................................................................................................................22
Description....................................................................................................................................................................................................22
Modes ...............................................................................................................................................................................................................23
Switching Menus ................................................................................................................................................................. 24
Changing Settings............................................................................................................................................................... 24
User Mode List.............................................................................................................................................................................................25
Service Mode List.......................................................................................................................................................................................27
Option mode List.......................................................................................................................................................................................29
Error Log Check (error log check menu)] ...................................................................................................................................30
ERROR CODE LIST ..........................................................................................................................................................................................31
LAMINATION ERRORS........................................................................................................................................................ 34
LAMINATION WARNINGS ................................................................................................................................................. 34
ERROR CODE DETAILS................................................................................................................................................................................35
Code 01-01-to 3F-XX ............................................................................................................................................................ 35

Service Manual_AVA1_ENG-20220922_I 3
Code 40-XX to BF-01........................................................................................................................................................... 57
EXPLODED VIEW............................................................................................................................................................................................65
SENSORS-MOTORS LOCATION DRAWINGS...................................................................................................................................77
SWITCHES-BOARDS-THERMISTOR-FANS LOCATION DRAWINGS ..................................................................................78
SENSORS / MOTORS/ FANS/SWITCHES FONCTION LIST........................................................................................................79
SENSOR CHECK................................................................................................................................................................................................81
ACTION CHECK ................................................................................................................................................................................................83
PM1: Card ........................................................................................................................................................................................................83
PM2: Card .......................................................................................................................................................................................................83
PM3: Turn ...................................................................................................................................................................................................... 84
HB1: Card........................................................................................................................................................................................................ 84
HB2: Film.........................................................................................................................................................................................................85
DM1&DM2: Ink..............................................................................................................................................................................................86
DM3&DM4: Film..........................................................................................................................................................................................87
DM5: Head..................................................................................................................................................................................................... 88
DM6: Heat.......................................................................................................................................................................................................89
DM7: Decurl...................................................................................................................................................................................................89
Card Pass Test ............................................................................................................................................................................................ 90
Error Log Check......................................................................................................................................................................................... 90
Printer Setup.................................................................................................................................................................................................91
Revision Check........................................................................................................................................................................................... 94
Card Setup .....................................................................................................................................................................................................95
Option Connection Mode List............................................................................................................................................................97
SPARES PART LIST.........................................................................................................................................................................................98
PARTS REPLACEMENT RECOMMENDATION.................................................................................................................................99
AVANSIA PRINT CALIBRATION ............................................................................................................................................................100
Test Pattern X: Print Position Adjustment................................................................................................................................101
Test Pattern Y: Print Density ............................................................................................................................................................102
Test Pattern Z: Print Uniformity .....................................................................................................................................................103
Print Test U: Vertical color shifting...............................................................................................................................................104
Print Test D: Horizontal color shifting.........................................................................................................................................105
Test Pattern B: Edge line or faded line detection, Uniformity, Density .................................................................107
REPLACEMENT PROCEDURES.............................................................................................................................................................108
Tools required............................................................................................................................................................................................109
Step 1 – REAR BLACK COVER – S10204........................................................................................................................................110
Step 2 –REAR TOP COVER – CP011784.......................................................................................................................................... 111
Step 3 – REAR SIDE COVER - LEFT AND RIGHT – CP011785 – CP011786 ................................................................... 113
Step 4 – FRONT SIDE COVER: RIGHT – CP011787...................................................................................................................114
Step 5 – FRONT SIDE COVER: RIGHT– CP012516..................................................................................................................... 116
Step 6 – TOP BLACK COVER – S10203 .......................................................................................................................................... 121
Step 7 – MAIN BOARD – S10195........................................................................................................................................................ 123

Service Manual_AVA1_ENG-20220922_I 4
Step 8 – POWER SUPPLY – S10196................................................................................................................................................. 128
Step 9 – HEAT ROLLER MODULE – S10248 ...............................................................................................................................130
Step 10 – HEAT ROLLER – CP011845.............................................................................................................................................. 137
Step 11 – CLEANING ROLLER STATION - S10197 .....................................................................................................................145
Step 12 – OPTICAL SENSOR (SN9-SN12) – CP011847 ............................................................................................................147
Step 13 – OPTICAL SENSOR (SN6) – CP011854.........................................................................................................................150
Step 14 – OPTICAL SENSOR (SN2, SN24) – CP011854-CP012327 ................................................................................... 155
Step 15 – DECURL MODULE – CP011976.......................................................................................................................................161
Step 16 – PRINT HEAD – S10143........................................................................................................................................................174
STEP 17 - BUSHING Ø6 Ø10 LG6 WITH FLATS – CP013577 ................................................................................................181
STEP 18 – FRONT COVER - CP013456...........................................................................................................................................182
STEP 19 – ROLLER:PRINT PLATEN - CP013457........................................................................................................................184
STEP 20 – ROLLER: FILM - CP013659............................................................................................................................................190
ROUTINE PRINTER CLEANING..............................................................................................................................................................198
Cleaning roller replacement............................................................................................................................................................203
MANUAL PRINTER CLEANING .............................................................................................................................................................206
Feeding roller cleaning.......................................................................................................................................................................207
Flip over rollers cleaning....................................................................................................................................................................209
Transport rollers cleaning .................................................................................................................................................................. 212
Primary transfer rollers cleaning ................................................................................................................................................... 215
Cleaning rollers cleaning.................................................................................................................................................................... 219
Filter Cleaning .......................................................................................................................................................................................... 222
Print head cleaning............................................................................................................................................................................... 224
PRINTING TROUBLESHOOTTING ....................................................................................................................................................... 227
Ribbon Key Error 67-05....................................................................................................................................................................... 229
COLOR SHIFTING .................................................................................................................................................................................... 230
Color shift: Cleaning ......................................................................................................................................................... 231
Color shift: Adjustment ................................................................................................................................................... 232
MISSING PRINTING ................................................................................................................................................................................ 236
Missing printing or faded areas ................................................................................................................................... 236
Missing printing: Metal plate adjustment................................................................................................................ 237
Missing printing: White line(s) on the prints .......................................................................................................... 239
Poor quality printing/output too pale....................................................................................................................... 240
Deprecated........................................................................................................................................................................... 241
COLORED WRINKLES ..........................................................................................................................................................................242
Film cassette film tilt adjustment method............................................................................................................................. 243
Color wrinkles: Cleaning ................................................................................................................................................. 246
Color wrinkles: Color ribbon .......................................................................................................................................... 246
Color wrinkles: Print head.............................................................................................................................................. 246
Deprecated........................................................................................................................................................................... 247
Color wrinkles: Creased ribbon .................................................................................................................................... 249

Service Manual_AVA1_ENG-20220922_I 5
CLEAR WRINKLES.................................................................................................................................................................................. 250
Clear wrinkles: Clear film ................................................................................................................................................ 251
Clear wrinkles: cassettes................................................................................................................................................. 251
Clear wrinkles: used film rolls ....................................................................................................................................... 252
Clear wrinkles: cassettes................................................................................................................................................. 253
Clear wrinkles: Adjustment ........................................................................................................................................... 255
LAMINATION ISSUE............................................................................................................................................................................... 256
Rubbing mark ..................................................................................................................................................................... 258
Heat roller ............................................................................................................................................................................. 260
Clear film ............................................................................................................................................................................... 261
Card quality.......................................................................................................................................................................... 261
EDGE LINE ............................................................................................................................................................................ 262
Black stains on cards / Ripoff........................................................................................................................................ 263
LOADING CARDS PROBLEMS ......................................................................................................................................................... 265
AVANSIA DRIVER SETTINGS .................................................................................................................................................................266
Graphics tabs functionalities........................................................................................................................................................... 267
Color settings from Graphics (front side)................................................................................................................. 267
Black panel settings: ........................................................................................................................................................ 268
No-transfer area setting:................................................................................................................................................. 270
UV layer transfer ................................................................................................................................................................ 271
Configuration tab .............................................................................................................................................................. 272
Maintenance tab ................................................................................................................................................................ 274
Printer Utilities.................................................................................................................................................................... 284
Block plan for electric parts..................................................................................................................................................................286
MAIN BOARD plan ....................................................................................................................................................................................... 291
FIND TECHNICAL INFORMATION ONLINE ................................................................................................................................... 292

Service Manual_AVA1_ENG-20220922_I 6
INTRODUCTION
Copyright
Evolis © April 2022. All rights reserved.
Copyright notice
Users must observe the copyright regulations applicable in their country. This manual must not be
photocopied, translated, reproduced, or transmitted, in whole or in part, for any reason and by any
electronic or mechanical means whatsoever without the express written consent of the Evolis Company.
All the information contained in this document is subject to change without prior notice.
Evolis cannot be held liable for any errors that may be found in this manual, or for any loss or damage
arising accidentally or as a result of dissemination or use of this manual.
Trademarks
Avansia, Evolis Premium Suite and Evolis High Trust are trademarks of Evolis. All other trademarks belong
to their respective holders.
Warranty
Refer to the warranty notice supplied with your printer for warranty terms and conditions and limitations.
Environmental information
Evolis is committed to helping the environment by reducing the energy consumption of its products.
Recycling of end-of-life products
The manufacture of the equipment that you have purchased required the extraction and use of natural
resources. It may contain materials that are hazardous to health and the environment.
To prevent the dispersal of such materials into our environment and reduce the pressure on our natural
resources, we recommend that you use existing collection systems. These systems will appropriately re-
use or recycle most of the materials in your end-of-life equipment.
The crossed-out dustbin symbol on your device is a reminder to use these systems.
If you need further information on collection, re-use and recycling systems, contact your local or regional
waste management body.
Do not hesitate to contact us to find out more by visiting our website at www.evolis.com or by emailing
the following address:[e-mail].

Service Manual_AVA1_ENG-20220922_I 7
Thank you for choosing an Evolis printer.
Using your new printer, you will be able to create a wide variety of high-quality cards and badges which
can be printed in various thicknesses, colors and styles. This printer uses consumables and accessories
available from Evolis. For further details, visit our website at www.evolis.com.
Warranty registration
Please register online at www.evolis.com to receive our special offers and general information.
Once on the website, click on SUPPORT/PRINTERS/Avansia/GUARANTEES then on Register my product
and fill in all the fields, giving in particular the model and serial number found on your printer.
Getting started
The purpose of this user guide is to guide you, step by step, through your printer and how it works. Take
some time to read it to better understand your printer and its features, and to save time during installation
and use.
As with all Evolis products, a great deal of care has been taken over this manual. Should you find an error,
however, please let us know by emailing us at inf[email protected].
Contents
The bookmarks found top left of your screen can be used to navigate between the various sections in this
user guide.
Icons
The following icons are used in this manual to highlight important information:
Information providing further details or depth about certain points in the main text.
Indicates that failing to take the recommended action is liable to damage your printer.
Read closely this manual.

Service Manual_AVA1_ENG-20220922_I 8
Getting started
Unpacking
Your printer is supplied with several accessories that we ask you to look at closely. This list may vary
depending on your location.
The printer is shipped in special packaging designed to prevent any damage in transit. If you notice any
visible damage, do not hesitate to contact the shipper, and immediately inform your Evolis dealer, who
will tell you the procedure to follow.
Evolis takes great care over the quality of its packaging, and we ask that you keep this packaging
somewhere clean and dry.
You will be asked for the full original packaging (outer box, inner wedges, and protective bags)
in the event that the printer is returned. If the printer is returned without its original packaging
and components are damaged in transit, these components will no longer be covered by the
warranty. You will be charged for new packaging for shipping the printer back to you.
Accessories supplied with your printer:
•Power supply unit - SWITCHBOX Type F10723-A or CWT Type KPL-065M.
•Mains power cable.
•USB cable.
•Installation, documentation and software CD-ROM.
•Starter cleaning kit.
•Warranty notice.
If any of these components is missing, please contact your Evolis dealer. Use only the power cable supplied
with your Evolis printer.
Use only the USB cable supplied with your Evolis printer.
The Evolis printer must be placed in a dry location, protected from dust and draughts but well-
ventilated. Take care to keep your printer on a flat, sturdy surface able to bear its weight.

Service Manual_AVA1_ENG-20220922_I 9
DESCRIPTION OF THE PRINTER
1. Top cover
2. Control Panel
3. Front cover
4. Front cover button
5. On-off switch
6. Card output hopper
7. Card ejection slot
1. Card input feeder
2. Feeding roller
3. Trapdoor cover
4. Card case lock
1. Reject slot
2. Peripheral USB socket
3. Ethernet socket (Lan cable port)
4. Port for enhancing function
5. Security cable slot
6. Power cable socket
7. Filter

Service Manual_AVA1_ENG-20220922_I 10
1. Card feeding wheel
2. Reverse feeding wheel
3. Cleaning roller
4. Cleaning tape cassette
5. Reverse wheel
6. Ink ribbon cassette
7. Transfer film cassette
8. Key holder
Connecting the output hopper Connecting the reject box

Service Manual_AVA1_ENG-20220922_I 11
Connecting the printer
Connection to the power supply
The printer must be connected to a properly protected and earthed electrical installation.
FI: Laite on liitettävä suojamaadoitus koskettimilla varustettuun pistorasiaan.
NO: Apparatet må tilkoples jordet stikkontakt.
SE: Apparaten skall anslutas till jordat uttag.
DK: Printeren skal tilsluttes til en korrekt beskyttet og jordforbundet el-installtion.
1. Connect the power cable to the printer.
2. Next plug the end of the power cable into an earthed power socket.
3. The printer is powered on: the control panel lights up showing the printer is working properly. If
the control panel does not light, then either installation has not been carried out correctly or the
printer is not working properly. Check the installation.
Before attempting any maintenance, ensure that the power cable is always unplugged. For
your personal safety, ensure that the cable remains easy to access, especially in the event of an
emergency.
The printer switches to hibernation mode after 60 minutes in standby mode.
Connecting the USB cable.
Under no circumstances should you connect the USB data cable before installation of the
printer driver is complete.
Refer to the section on printer driver installation available in the Avansia User Guide for further
details and follow the instructions carefully.

Service Manual_AVA1_ENG-20220922_I 12
GENERAL OUTLINE
Overall Explanation Basic specifications
For the basic specifications of this printer, refer to the “User Guide Avansia”.
Mechanism components and functions
This printer consists of a primary transferring unit, secondary transferring unit, de-curling unit, card
transferring unit, card feeder unit, cleaning unit, flip section, card stacker unit, and a unit for mounting
optional parts.
Card flow
Transfer Film
Ink Ribbon
Transfert unit
Unit color
Name
Primary transfer unit
8
Ink ribbon cassette
9
Transfer film cassette
10
Print head
Secondary transfer unit
1
Card feeder
2
Cleaning rollers
3
Flip over
4
Decurl unit
5
Card stacker
6
Reject box
Optional unit
7
Optional parts
11
RFID Key
Primary transfer unit
Secondary transfer unit
1
2
3
4
5
6
7
9
8
10
11

Service Manual_AVA1_ENG-20220922_I 13
•Primary transferring unit
The primary transferring unit uses a 600-dpi thermal line scan head, which is installed near the inked ribbon.
It transfers ink from the inked ribbon to the transfer film while moving the inked ribbon and transfer film.
This mechanism is called thermal transferring. The inked ribbon uses dye-sublimation (CMY: cyan, magenta,
yellow) for printing-colored images, pigment-sublimation (K: black), a heat seal, a stripping section, and a UV
unit.
•Secondary transferring unit
The secondary transferring unit uses a heat roller to transfer images from the transfer film to the cards. This
mechanism is also called thermal transferring.
•Card feeder unit
The card feeder is installed in the upper portion of the printer. Cards are stacked horizontally with the surface
(printing surface) of the cards facing the left side of the printer. Users can load a maximum of 250 cards
(thickness: 0.76 mm) at once.
The card feeder is a detachable cartridge, so it is easy to attach or detach it during printing. The cartridge
allows user to refill cards when it is attached to or detached from the printer.
•Cleaning unit
The cleaning unit removes dust and dirt by touching the cleaning roller to the cards.
The cleaning roller collects dust and dirt that is removed from the cards, and the cleaning tape removes
them from the cleaning roller.
Periodic maintenance of the cleaning tape will ensure cleaning function stability.
•Flip card unit
Functions of the flip section include taking in cards from card feeder, delivering cards to the secondary
transferring unit, transferring cards to optional units, and ejecting rejected cards.
•Decurl unit
The de-curling unit flattens warped cards delivered to the secondary transferring unit.
•Card ejection units
The printer has two card ejecting units: one on the left (card ejecting unit 1) and one on the lower right (card
ejecting 2). You can change the settings to choose which one will receive normally printed cards and which
one will receive mistakenly ejected cards. The default setting for the units has card ejecting unit 1 receives
normally ejected cards and card ejecting unit 2 receive mistakenly ejected cards.
•Unit for mounting optional parts
This unit accepts the magnetic R/W unit, R/W unit for various non-contact IC cards (e.g., Mifare and Felica),
and the contact R/W unit.
•RFID Key holder
It controls the type and consumed amount of ink ribbon through communication with ID-key attached to the
ink ribbon.
•Print head
The Printhead is heated to transfer the Ink Ribbon's ink to the Transfer Film to form images.

Service Manual_AVA1_ENG-20220922_I 14
Cassette Handling Good Practices
Avansia cassettes must be handled with care because cassettes play a very important role in
print and lamination quality.
Cassettes have reference posts that must remain in original position:
Otherwise, when a reference post is torn, it can create used roll winding issues: badly spun used roll will
pull ribbon/film unevenly which will make film/ribbon crease.
For instance, creased ribbon generates colored wrinkles and creased film generates clear wrinkles.
Basically, good practice for cassette handling consists in making sure cassette reference posts remain in
original position when storing or manipulating the cassettes.
OPPOSED TO
OR

Service Manual_AVA1_ENG-20220922_I 15
Image printing process
Primary Transfer Feed Roller (Platen Roller)
Overview
Presses the Ink Ribbon and Transfer Film against the Printhead.
Control description
The up and down operation is controlled by the Platen Lift Motor (DM5).
In addition to the Primary Transfer Feed Roller (Platen Roller), the Platen Lift Motor (DM5) also
controls the up and downmovement of the Film Nip Roller.
1. Up position: Primary Transfer Roller (Platen Roller) upward (release (uppermost)), Film Nip Roller
upward (release).
2. Home position: Primary Transfer Roller (Platen Roller) upward (release (intermediate)), Film Nip
Roller downward (nip).
3. Down position: Primary Transfer Roller (Platen Roller) downward (pressure), Film Nip Roller
downward (nip).
[1] [2] [3]

Service Manual_AVA1_ENG-20220922_I 16
Ink Ribbon
Overview
Control description
Panel configuration: There are two types, a YMCK four panel configuration and a YMCKK five panel
configuration. Regarding position control of the Ink Ribbon, resolution is calculated by measuring the
number of clock occurrences from the Ribbon Feed Length Sensor (Wind Up Axis and Supply Axis, SN10
and SN11 - respectively), generated at the time when it passes through the K panel detected by the
Ribbon Beginning Sensor (SN9).
Based on this resolution, position control of the Ink Ribbon for the Y, M, and C panel is performed by the
relative number of clocksfrom the K panel.
Since resolution varies according to the remaining Ink Ribbon amount, the resolution is updated
every time K panel passesthrough.
1. Panel configuration of the Ink Ribbon
2. Detection level of the Ribbon Beginning Sensor (SN9)
[1]
[2]
Transfer Film
Control description
Regarding position control of the Transfer Film, resolution is calculated by measuring the number of
clock occurrences by theFilm Feed Length Sensor (Supply Axis and Wind-Up Axis, SN14 and SN15 -
respectively), generated at the time of passing through the transfer panel detected by the Film
Beginning Sensor 1 (SN12) or Film Beginning Sensor 2 (SN13).
Based on this resolution and the number of times passing through the beginning mark, position control
of the film is performed.Since the resolution varies according to the remaining amount of the Transfer
Film, it is renewed every time one panel passes through.
At printing, repeat the movement of rewind and take-up every color to transfer 4 colors (Y/M/C/K) ink by
overlapping on the panel.
1. Panel configuration of the Transfer Film
2. Detection level of the Film Beginning Sensor 1/2 (SN912/SN13)
[1]
[2]
C K Y
M
C K Y
M

Service Manual_AVA1_ENG-20220922_I 17
Initial Operation of Ink Ribbon and Transfer Film
Overview
Control description
The RFID PCB makes initial communication with Main board and ID-key to acquire the type and
remaining amount information ofink ribbon. When ink ribbon is used by initial operation, the remaining
amount information of ink ribbon is updated.
Take-up operation of the Ink Ribbon and Transfer Film is performed to detect the remaining amount and
type of ribbon.
If an error such as undetected clock of the ribbon spool is detected during the take-up operation, the
operation is stopped, anderror information is displayed on the operation panel to prompt the operator
to check the status of the ribbon.
In addition, if the end of the ribbon is detected, the operation is stopped, and error information is
displayed on the operation panel to prompt the operator to replace the ribbon.
By setting [Initialize Mode], it is possible to omit the above operation during initialization. When
omitted, the above operation isperformed when printing for the first time.
If the ribbon type is changed after this initialization operation, the initialization operation will be
performed in response to the next print request.
Secondary Transfer Assembly
Overview
Transferring the image from the Transfer Film to the card.
No.
Name
Function
[1]
Heat Roller
Retransfers the image primarily transferred to the film onto to
the card.
[2]
Peeling Shaft
Peels the film from the card after the secondary transfer.
[3]
Card Feed Roller 3
Presses the card against the Heat Roller during the secondary
transfer.
[3]
[2]
[1]

Service Manual_AVA1_ENG-20220922_I 18
Heat Roller
Overview
Primarily transferred film is transferred to the card using a Heat Roller.
Temperature control
The Transfer Film on which print data is formed and the leading edge of the card are pressed by a Heat
Roller heated to a required temperature in advance and Card Feed Roller 3. The card and the Transfer
Film are fed until the trailing edge of the card passesthrough the Heat Roller, thereby transferring print
data formed on the Transfer Film to the card.
The heat roller temperature changes according to the ambient temperature and card type. After the
secondary transfer, the Heat Roller maintains a temperature necessary for transfer.
In addition, when one hour has passed in the standby state, it stops the temperature control of the
Heat Roller, or turns off theprinter's main power supply according to user mode's [Power Save Mode]
setting.
Up/down operation control
The up and down operation is controlled by the Heat Roller Lift Motor (DM6).
In addition to the Heat Roller, the Heat Roller Lift Motor (DM6) also controls the up and down operation
of the Peeling Shaft.
1. Up position: Heat Roller upward (pressure), Peeling Shaft upward (card lifting position).
2. Intermediate position: Heat Roller upward (release (Intermediate position)), Peeling Shaft upward
(card lifting position).
3. Home position: Heat Roller downward (release (cover close)), Peeling Shaft downward (release).
[1] [2] [3]

Service Manual_AVA1_ENG-20220922_I 19
Feeding & Transport process
1. Cards [1] set in the card cassette are
supplied one at a time by the Supply Roller
[2].
2. Dust adhered to the card is removed by the
Cleaning Roller [1].
3. The cleaned card is fed to the Reverse
Assembly [3] by Reverse Rollers 1 [1] and 2
[2].
4. The Reverse Assembly [1] rotates, and the
card rotates.
5. The card is fed to the print standby position
by Card Feed Rollers 1 [1]
and 2 [2] while
skewing is corrected by the Feed Guide
Assembly [3].
6. The card is fed by the Card Feed Roller 3 [1],
and the first side is printed.
[1]
[2]
[1]
[1]
[2]
[3]
[1]
[1]
[2]
[3]
[1]

Service Manual_AVA1_ENG-20220922_I 20
7. The card is fed to the Decurl Assembly [3] by
Card Feed Rollers 4 [1] and 5 [2]. If there is a
decurl setting, the Decurl Plate [4] of the
Decurl Assembly descends and corrects
the curling of the card. The card is fed and
ejected by the Card Feed Roller 5 (step 13).
8. In case of printing on the second side, the
card is fed to the Reverse Assembly [1].
9. The Reverse Assembly [1] rotates, and the
card rotates 180 degrees and turns over.
10. The card is fed to the print standby position
by Card
Feed Rollers 1 [1] and 2 [2] while
skewing is corrected by the Feed Guide
Assembly [3].
[1]
[2]
[3]
[4]
[1]
[1]
[1]
[2]
[3]