Evolis Unitech Securion User manual

英文使用手冊
Securion
2010.08 印製

Securion User Guide part number: KU08E Rev. A0 - Evolis Card Printer © March 2007

CCooppyyrriigghhttIInnffoorrmmaattiioonn
Evolis Card Printer © March 2007. All rights reserved.
CCooppyyrriigghhttNNoottiiccee
Users must respect the copyright laws applicable in their country. This manual must not be photoco-
pied, translated, reproduced or transmitted in whole or in part for any reason and by the means that
might be, albeit electronic or mechanical, without the express, written authorisation of the company
Evolis Card Printer.
All information contained herein may be subject to modification without prior notice.
Evolis Card Printer accepts no liability for any possible errors herein, nor for any accidental damage or
damage caused through the dissemination or the use of this manual.
TTrraaddeemmaarrkkss
Securion is a trademark and Evolis is a registered trademark of Evolis Card Printer.
Windows and MS.DOS are registered trademarks of Microsoft Corp. All other trademarks or registered
trademarks are marks of their respective holders. eMedia Card Designer is a trademark of Mediasoft
Technologies.
IIccoonnss
Throughout this manual, different icons highlight important information, as follows:
Indicates information that emphasizes or supplements important points of the main text.
Advises you of information that is essential to complete a task, or points out the importance of
specific information in the text.
Advises you that failure to take or avoid a specific action could result in physical harm to you, or
could result in physical damage to the hardware.
WWaarrrraannttyyIInnffoorrmmaattiioonn
Refer to the Warranty booklet enclosed with your Evolis printer for terms and conditions.
RReettuurrnnMMaatteerriiaallssAAuutthhoorriizzaattiioonn
In order to make a warranty claim you must contact an Evolis Reseller. You will be responsible for packa-
ging the printer for shipment and the costs of shipping and insurance of the printer from the point of
use of the printer to the Evolis Reseller. The Evolis Reseller will bear the costs of shipping and insuring
the printer from the repair location to the address from which the printer was shipped.
Before returning any equipment for in-warranty or out-of warranty repair, contact an Evolis Reseller or
an Evolis Repair Center (ERC) for a Return Materials Authorization (RMA) number. Repack the equip-
ment in the original packing material and mark the RMA number clearly on the outside of the box. For
more information about RMA or Evolis warranty statements, refer to the Warranty booklet enclosed
with your Evolis printer.
PPrroodduuccttDDiissppoossaall
WEEE Directive
This symbol indicates that when the last user wishes to discard this product, it must be sent
to appropriate facilities for recovery and recycling.
By not discarding this product along with other household-type waste, the volume of
waste sent to incinerators or landfills will be reduced and natural resources will be conser-
ved. Your Evolis printer should be recycled according to your local standards. For more
information, please contact Evolis at: [email protected].

TThhaannkkssffoorrcchhoooossiinnggEEvvoolliiss
ttooppeerrssoonnaalliizzee
aannddllaammiinnaatteeyyoouurrbbaaddggeess
Using the latest printing and encoding technologies, Evolis
Securion offers its users both performance and quality.
Evolis Securion , fully adapted to both small and mid-volume
runs, combines simplicity of use and functional richness: high
quality printing and laminating, magnetic encoding, encoding of
both contact and contactless smart cards.
The ‘Evolis Genuine Product’ line of consumables linked to the
printer was specifically developed and optimized to guarantee
the highest quality of printing and laminating.
Using these consumables increases the life span of your badges
and of your Securion printer.
As for all Evolis products, particular care has been used in writing
this manual. But if an error has still managed to slip into these
pages without our wanting it, please let us know by sending an
e-mail to [e-mail]. Evolis will then do everything in its
power to correct the problem and give you complete satisfaction.

11Install the Evolis Securion printer
Technology and benefits ...........................................06
Initial approach ......................................................07
Install your printer..................................................08
Check the components shipped
Connect the cables
Installing the ribbons...............................................09
Monochrome or color ribbon
Laminating film
Installing the cards .................................................12
Types of cards
Placement in the feeder
Adjustment of thickness
Removing the personalized cards ...............................14
22Setting of parameters
Windows print driver ...............................................15
Installation of the print driver
Manual installation of the driver
Properties of the driver
Printer menus........................................................23
Discovering the printer menu
Architecture of the menu
Parameters
33Error messages and diagnostics
Notification of messages...........................................26
LCD display and LED indicator
Port Monitor
Interpretation of messages .......................................26
Status messages
Alert messages
Error messages
Diagnostics assistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Print and interpret a test card
Identify the software versions installed
Contents

44Servicing and Maintenance
Ordinary maintenace ...............................................32
Clean the card feed module
Service the cleaning roller
Clean the print head
Remove the cards from the reject box
Maintenance .........................................................37
Replace the cleaning roller
Replace the print head
Update the Firmware
Update the print driver
Troubleshooting .....................................................42
Free a card in the print unit
Free a card in the lamination unit
Free a card in the flipover unit
Improve printing quality
Assistance.............................................................46
Network of Evolis partners
Look for information on www.evolis.com
Download updates
55Characteristics
Declaration of conformity..........................................47
Printer specifications...............................................48
Printer options .......................................................49
List of “Evolis Genuine Product” consumables ...............50
Magnetic encoding ..................................................51
Smart card contact station ........................................53
Contents

I
In ns st ta al ll lt th he eE Ev vo ol li is s
S
Se ec cu ur ri io on np pr ri in nt te er r
The aim of this first part is to assist you, step-by-step, in
discovering your new printer and putting it to work for you.
By taking the time to review these few pages, you will get more
detailed knowledge about Securion and its capabilities, while
optimizing the time needed to install and start using the product.
TTeecchhnnoollooggyyaannddbbeenneeffiittss
Evolis Securion is for all users who want to personalize highly secure badges. The personalization
cycle includes a series of operations that are consistent with the nature of the requirements.
For example, after a first and optional card encoding stage (magnetic stripe, contact or contactless
chip), personalization continues with printing on one or both sides of the card.
The printing process is completed by a lamination cycle that involves putting a protective film on one
or both sides of the card.
The use of holographs (holograph ribbons) makes it possible to combat fraud and counterfeiting of
the badges. Evolis offers a wide range of consumables that can be adapted to the needs of an enter-
prise as requested.
In addition to great security, plastic lamination means greater badge durability, generally between 5
and 10 years, depending on the quality of the components and the manner in which they will be used.
Evolis Securion is an ideal personalization solution for company badges, student badges, drivers’
licenses, identity cards and, more generally, for any badge requiring a very high quality of printing
combined with total security.
1
1
>06

>07
IInniittiiaallaapppprrooaacchh
The Evolis Securion printer is comprised of the following components referenced on the diagram:
1. 100-card feeder
2. Encoding and printing station
3. Flip-over station
4. Defective card reject box with a
capacity for 15 cards
5. Card laminating station
6. 100-card capacity hopper
7. 4-button control panel and 2-line LCD
display
8. LED indicator light for displaying
printer activity
9. Centralized locking of the cover to
secure all internal components
The following items are located behind
the printer:
10. Power supply connector
11. USB computer connector
12. RJ45 Ethernet connector
13. DB9 connector(s) (option)
14. Power switch
15. Location of Kensingston®type bolt
You will also find the identification label (16),
specifically containing the serial number of
the unit and its MAC address (necessary for
hooking up to the Ethernet network -
TCP/IP).
Finally, the encoding and printing
module includes a number of components,
including:
17. 300 dpi thermal color-printing head
18. Card cleaning roller (absorption of
residual dust on cards)
19. Gauge for adjusting card thickness
from 0.25 mm (10 mil) to 1 mm (40 mil)
20. Magnetic encoding head option
21. Smart card contact station
22. Contactless card encoding antenna
(RFID)

>08
IInnssttaallllyyoouurrpprriinntteerr
The Evolis Securion printer must be set up in a dry, well-ventilated location protected against dust
and air currents.
In point of fact, during the lamination operation, the temperature of the module can attain a peak of 180º,
it is therefore recommended that the instructions regarding the operating environment be followed.
In addition, make sure you install your Securion on a sturdy flat surface that can support its weight
of around 15 kg (33 Lbs).
Finally, it is essential to allow free access to the connectors and to the power switch located in back
of the unit.
Because of the weight of the entire unit (15 kg - 33 Lbs), and to prevent any
physical damage, do not attempt to install the machine by yourself.
CChheecckktthheeiitteemmsssshhiippppeedd
The Evolis Securion printer is shipped with a set of accessories that we invite you to examine.
Please take note that this list may vary in terms of the geographic area where you are located.
Securion is shipped in an original container specially designed to ensure that the product is protec-
ted against any risk of damage during shipment.
In the event of visible damage at the time of delivery, do not hesitate to carry out all required steps
as far as the shipper is concerned, and immediately contact your Evolis dealer who will provide you
with all necessary assistance.
Evolis has paid particular attention to the quality of this shipping material, and we urge you to keep
it in a clean, dry space.
This packaging material will be required to return equipment.
During the manufacturer’s guarantee period, returning material without the original Evolis
packaging could cause you to lose the benefit of this guarantee !
The following parts are furnished with the Securion printer:
■Power supply unit - VP ELECTRONIQUE type PAC150M
■Main power cable
■USB cable (length 1:80 m) - Item # A5017
■CD-Rom Driver & Documentation
■CD-Rom eMedia Card Designer, badge design and personalization software including
the utilization of an Excel source data base
■Cleaning kit
■Evolis Limited Guarantee document (must be consulted)
In the absence of one of these components, please contact your Evolis dealer.
Only use the power supply delivered with your Securion:
VP ELECTRONIQUE type PAC150M.

>09
PPrree--iinnssttaallllaattiioonnaaccttiivvaattiioonn
Before installing the printer, please perform the following operations:
CCoonnnneecctttthheepprriinntteerrttootthheemmaaiinnppoowweerrssuuppppllyy
Connecting to the electrical system
Before hooking up to the electrical system, make
sure the switch on the back of the printer is on OFF (O).
Turn off the printer by pulling the plug out of the
socket, which must always be accessible.
This product must be connected to an electrical installation
that is correctly protected and grounded.
FI: Laite on liitettävä suojamaadoitus koskettimilla
varustettuun pistorasiaan
NO: Apparatet må tilkoples jordet stikkontakt
SE: Apparaten skall anslutas till jordat uttag
1. Connect the power supply cord to the power supply, then attach the power cord connector to the printer.
2. Then connect the end of the power supply cord to a grounded system outlet.
3. Power up the printer by turning the switch to ON (1).
4. The control panel display lights up and the message INITIALIZATION is displayed. Once the star-
tup sequence is completed, the menu displays READY and the driver LED is green and must be
steady. If the display does not light up when the power is turned on, or if the LED is not green
and/or if it flashes, this means that the installation was not done correctly or possibly that the
printer is not operating properly. Check the installation.
Prior to any maintenance action, always turn the power switch to
OFF (O) and disconnect the power supply cable.
For your own safety, these two components must remain accessible
at all times to permit emergency action
This product must be connected to a correctly protected and
grounded electrical installation
CCoonnnneeccttiinnggtthheeddaattaaccaabbllee
The data cable (USB, Ethernet or other) must never be connected before the installation of the
printer driver has been completed.
Refer to Chapter 2.1 and carefully follow these instructions.
IInnssttaalllliinnggtthheerriibbbboonnss
The Evolis Securion printer uses two types of ribbons:
■Color or monochrome ribbons for the printing module: identifiable by their core which is equip-
ped with a toothed wheel
■Special films for the laminating module characterized by their hollow core
The Evolis original ribbons and films are specially designed to guarantee optimum operation
of your equipment without any risk of damage. The use of films or ribbons from any other
source than Evolis could seriously damage the print head and the heating roller of the lami-
nating station, consequently entailing the immediate interruption of the factory warranty.