Extreme Tools RX723019RC-250 User manual

Extreme Tools, Inc.
740 Frontenac Road
Naperville, Illinois 60563
630.369.9303
www.ExtremeTools.net
72 inch Painted Steel
Roller Cabinet
© 2018
Model:
RX723019RC-250
250 lbs. Slides

Roller Cabinet Parts List
RX723019RC-250
250 lbs. Slides
25
4
1
11 26
18
16
9
14
21
12
21
8
6
15
20
27
19
22
7
3
23
13
24
5
2
4
31
Replacement keys may be ordered using the code that appears
on the face of the lock.
To order replacement parts, have the part number, tool box
color and quantity ready.
If under warranty, the serial number is REQUIRED to get
replacement parts.
Not all parts are available under warranty and may be
purchased separately.

PARTS LIST - RX723019RC-250
ITEM
NO.
PART NUMBER DESCRIPTION QTY.
1 RX7230-00 BODY WELDMENT 1
2
RXQDR-3A-250 DRAWER 3 ASSY 8
3
RXQDR-4A-250 DRAWER 4 ASSY 2
4
RXQDR-1A-250 DRAWER 1 ASSY 1
5
RXQDR-2A-250 DRAWER 2 ASSY 2
6
RXQDR-5A-250 DRAWER 5 ASSY 3
7
RXQDR-6A-250 DRAWER 6 ASSY 2
8
RXQDR-7A-250 DRAWER 7 ASSY 1
9
Z-ECRX PLASTIC END CAP 2
10
Z-LBA7200 LB ASSY 7200RC 3
11 304005
SEE KEY CODE ON LOCK 1
12
Z-GW24 24'' TUBULAR HANDLE 1
13
Z-LGL EXTREME TOOLS LOGO 1
14
Z-LGS
EXTREME TOOLS NAMEPLATE 1
15
Z-TRF979 ALUM. VERTICAL TRIM - 979 MM 2
16
Z-WT7230 LAMINATE TOP 1
17 Z-KBRX7230-38
KEYBAR ASSEMBLY 1
18
Z-CNRX7225-10 CONNECTING BAR (72) 1
19
Z-BTM1020MM M10 CASTER SCREWS 4
20
Z-WAM10S SPLIT LOCK WASHERS 4
21 Z-M6-1.0-30
M6-1.0 X 30 SOCKET HEAD SCREW
4
22
Z-MS L ALLEN
MS “L” SHAPED ALLEN WRENCH 1
23
Z-DL55-7230M 5530/7230 DRWR LINER-MED 1
24
Z-DL55-7230S 5530/7230 DRWR LINER-SM 1
25
Z-DL55-7230L 5530/7230 DRWR LINER-LG 1
26
Z-PNM6 6mm PUSH NUT 3
27
Z-CA6SB(CRX) 6 X 2 Mag CASTER (S/B) 4
28
Z-M6-1CB M6-1 CARRIAGE BOLT 3
29
Z-M6-1FN M6-1 FLANGE NUT 3
30
Z-CA6R(CRX) 6 X 2 Mag CASTER (RIGID) 2
31
Z-SL723019R/L-250
BALL BEARING SLIDE- 26.2"
25

Handle Installation
NOTE: Assemble the handle rst to make it easier to move the tool cabinet.
Position the handle over the holes in the cabinet and attach with the provided
(4) M6-1.0 x 30 socket head screws. Tighten securely.
ASSEMBLY
Drawer Removal
Pull drawer out so that it is almost
fully extended.
Push up on the black lever on one
drawer slide and at the same time
push down on the lever on the
other side.
With the levers in these positions,
pull the drawer out until it releases
from the drawer slides.
Drawer Replacement
Extend the drawer slides.
Careful align the brackets on
the sides of the drawers with the
slots of the cabinet slides. Insert
the brackets on the side of each
drawer into the slots of the cabinet
slides.
Once properly inserted,
completely close the drawer to
set the slides into their properly
functioning positions.
OPERATING PROCEDURE

MAINTENANCE
Lubricate the casters once a year with high quality ball bearing grease.
Lubricate the slides twice a year with high quality, petroleum-based
lubricant. This may be required more often If operating the tool box in colder
climates.
Use mild detergent and water to clean drawer fronts, drawer trim and other
surfaces.
Grease and oil can be removed with standard, non-abrasive, non-
ammable cleaning products.
Auto wax will help preserve the unit’s high gloss nish. Follow directions as
provided.

SAFETY
Do not attempt to lift the cabinet by its side handle using chains, ropes or lifting device.
Side handle may fail resulting in personal injury or damage to the product!
Use a forklift or similar lifting device with forks placed under the bottom of the tool box to
move if tool box cannot be moved by two people.
Close the drawers and lock the tool box before moving this product! If drawers are not
locked they could open and make the product unstable and tip which may cause personal
injury or damage to the product.
Do NOT stand on this product or lean on the drawer or work top.
Wear safety glasses when removing or repositioning the slides. The tool box could slip
resulting in personal injury.
Do NOT mount this product on a truck bed or other moving object. This may cause
personal injury or product damage. Mounting this product on any surface will void the
warranty.
Do NOT tow with power equipment. The product could tip which may cause personal
injury or product damage.
Do NOT alter this product in any manner or attach electrical equipment. This may cause
personal injury or product damage and will void the warranty.
If using the combination top chest and roller cabinet, the top chest MUST be secured to
the roller cabinet by following the directions provided. Not securing the top chest to the
roller cabinet may cause the product to become unstable which may cause personal injury
or damage to the product.
DRAWERS MUST BE CLOSED AND TOOL BOX LOCKED USING KEYS
BEFORE MOVING!
The maximum weight for each drawer should not exceed 250 lbs. (113 kg) for single slides
and 500 lbs. (226 kg) for drawers with double slides.
Maximum overall weight should not exceed 3,600 lbs. (1,632 kg.)
Use caution when closing the chest lid. Remove hands from the area before closing to
prevent personal injury.
Do NOT pull this product. Push the product to prevent personal injury.
ENGAGE THE BRAKES when not moving this product. Locked casters prevent the
product from rolling which may result in personal injury or damage to the product.
This product may become unstable and tip if more than one drawer is open at a time. To
prevent personal injury or damage to product, OPEN ONLY ONE DRAWER AT A TIME.
Lock product and properly secure before moving with a forklift or other device.
Keep the product on a level surface. The product could become unstable and tip if stored
or moved on an uneven surface which may result in personal injury or product damage.
Remove the work surface from the roller cabinet before installing top chest.
WARNING
CAUTION - IMPORTANT PRODUCT INFORMATION