FabiaTech FX5206 User manual

FabiaTech Corporation
IPC Solution
Website: http://www.fabiatech.com
Email: [e-mail]
Small Cube System
Fanless Series
FX5206 User’s Manual
DEC 2013
Version: 1.0
Part Number: FX5206

Copyright
Copyright © 2013 FabiaTech Corporation, The content of this publication may not
be reproduced in any part or as a whole, transcribed, stored in a retrieval system,
translated into any language, or transcribed in any form or by any means,
electronic, mechanical, and magnetic… or otherwise without the prior written
permission of FabiaTech Corporation.
Disclaimer
FabiaTech makes no representation of warranties with respect to the contents of
this publication. In an effort to continuously improve the product and add features,
FabiaTech reserves the right to revise the publication or change specifications
contained in it from time to time without prior notice of any kind from time to time.
FabiaTech shall not be reliable for technical or editorial errors or omissions, which
may occur in this document. FabiaTech shall not be reliable for any indirect,
special, incidental or consequential damages resulting from the furnishing,
performance, or use of this document.
Trademarks
Trademarks, brand names and products names mentioned in this publication are
used for identification purpose only and are the properties of their respective
owners.
Technical Support
If you have problems or difficulties in using the system or setting up the relevant
devices, and software that are not explained in this manual, please contact our
service engineer for service, or send email to sup[email protected].
Returning Your Board for Service & Technical Support
If your board requires servicing, contact the dealer from whom you purchased the
product for service information. You can help assure efficient servicing of your
product by following these guidelines:
A list of your name, address, telephone, facsimile number, or email address
where you may be reached during the day
Description of you peripheral attachments
Description of your software (operating system, version, application
software, etc.) and BIOS configuration
Description of the symptoms (Extract wording any message)
For updated BIOS, drivers, manuals, or product information, please visit us at
www.fabiatech.com.
ii

Table of Contents
FX5206 User’s Manual ...........................................................................................................i
Chapter 1 Introducing the FX5206 System ............................................................................... 1
Overview..................................................................................................................................1
Series Comparison Table.......................................................................................................2
Layout.......................................................................................................................................3
Specifications..........................................................................................................................4
Packing List ..............................................................................................................................5
Chapter 2 Hardware Installation ............................................................................................... 7
Before Installation ...................................................................................................................7
Removing Covers –Installing Hardware...........................................................8
LED Indicators & I/O Peripheral Connectors ................................................11
Connecting the DC Power and Power Switch ............................................14
Jumper Setting ..................................................................................................15
Chapter 3 BIOS Setup............................................................................................................... 17
Overview................................................................................................................................17
BIOS Functions ...................................................................................................18
Keyboard Convention .....................................................................................19
Main Setup ............................................................................................................................20
Advanced Setup..................................................................................................................21
CPU Configuration............................................................................................22
IDE Configuration..............................................................................................23
Remote Access Configuration .......................................................................26
USB Configuration .............................................................................................28
Boot Setup .............................................................................................................................30
Boot Setting Configuration..............................................................................31
Boot Device .......................................................................................................33
USB Drives ...........................................................................................................34
Security setup........................................................................................................................35
Chipset Setup........................................................................................................................37
Northbridge Configuration..............................................................................38
Southbridge Configuration..............................................................................41
iii

Chapter 4 Software Installation ............................................................................................... 47
VGA Drivers ...........................................................................................................................47
WINXP Driver ......................................................................................................47
Audio Driver...........................................................................................................................48
WIN XP Driver .....................................................................................................48
LAN Driver (RTL 8111F)..........................................................................................................48
WIN XP Driver .....................................................................................................48
BIOS Flash Utility.....................................................................................................................48
Watchdog Timer ...................................................................................................................49
Watchdog Timer Setting ..................................................................................49
Setup Watchdog Timer Step - WDT0 and WDT1 ..........................................51
Chapter 5 Technical Reference .............................................................................................. 55
Trouble Shooting for Post Beep and Error Messages.......................................................55
Technical Reference............................................................................................................58
Physical and Environmental............................................................................58
Real-Time Clock and Non-Volatile RAM .......................................................58
CMOS RAM Map...............................................................................................60
I/O Port Address Map.......................................................................................61
Interrupt Request Lines (IRQ)...........................................................................62
Serial Ports ..........................................................................................................63
Appendix................................................................................................................................... 67
Dimension ..............................................................................................................................67
iv

v

FabiaTech Corporation
Chapter1IntroducingtheFX5206System
Overview
The FX5206 is an embedded system with low-power CPU module inside. This user’s
manual provides information on the physical features, installation, and BIOS setup
of the FX5206.
Built to unleash the total potential of the Vortex™ 86DX2 Processor, Able to support
800MGz CPU, this system supports one 10/100/1000 Base –T LAN port, PCIe Mini
Card connector for GPRS/GPS modules, audio, three USB 2.0 ports, and onboard
1GB DDR2 RAM, and a VGA controller.
Each FX5206 has one port for I/O communications. One RS-232C port is available.
The FX5206 is perfect for ATM machines, KIOSK, point-of-sales/point-of- information,
gaming and infotainment, measurement technology, lotteries, and banking and
small Embedded Control. The unit is only 95.0mm (D) X115.0mm (W) X30.2mm (H).
1

FabiaTech Corporation
SeriesComparisonTable
Model FX5206
System Processor Vortex™ 86DX2 800MHz
Memory
Onboard RAM DDR2 300/333 1GB
VGA Yes
Watchdog Timer Yes
Multi I/O One RS232
Storage One CFast and SD Card
USB 2.0 Port Three
Audio Ear-Phone And MIC-In
RJ45 LAN port
(10/100/1000 Mbps) One Realtek RTL8111F
PCIe Mini Card One
Operating Temperature 0~+ 50℃(32~113℉)
Storage Temperature -20~+60℃(4~140℉)
Dimensions (Unit: mm) 95(D) x 115(W) X 30.2(H)
2

FabiaTech Corporation
Layout
LAN
EAR-PHONEPOWER LED
ANTENNAANTENNA MIC COM
DC12~24V
+-
POWER SWITCH
USB
RESET
DC IN
CRT
3

FabiaTech Corporation
Specifications
Processor Board –
Vortex™ 86DX2 Low Power 800MHz CPU with 1GB DDR2-RAM.
I/O Outlets –
One 10/100/1000 base-TX Ethernet LAN port with RJ45.
One CRT and three USB ports (2.0) and one RS-232/422/485 serial port.
Two Audio connectors for Earphone-out and Microphone-In.
One PCIe Mini card socket modules, especially for WLAN/GPRS module.
One DC-In terminal block with power switch.
One push button reset switch and one power LED.
Storage Bay-
CFast Compact Flash socket for CFast Compact Flash modules.
One SD socket supports up to 32GB SDHC (Class 6).
Power requirement –
+12~+24V DC, 1.12A maximum (0.77A typical) with DC 19V input.
Dimensions -
95.0mm (D) x 115.0mm (W) x 30.2mm (H)
4

FabiaTech Corporation
PackingList
Upon receiving the package, verify the following things. Should any of the
mentioned happens, contact us for immediate service.
•Unpack and inspect the FX5206 package for possible damage that may
occur during the delivery process.
•Verify the accessories in the package according to the packing list and see
if there is anything missing or incorrect package is included.
•If the cable(s) you use to install the FX5206 is not supplied from us, please
make sure the specification of the cable(s) is compatible with the FX5206
system.
Note: after you install the FX5206, it is recommended that you keep the diskette or
CD that contains drivers and document files, and keep the document
copies, or unused cables in the carton for future use.
The following lists the accessories that may be included in your FX5206 package.
Some accessories are optional items that are only shipped upon order.
•One FX5206 embedded system.
•One 2-pin apartable terminal block.
•One compact disc includes software utility and manual.
Optional:
•One pack of half size mini PCIe module adapter kits.( P/N:0606010028G)
•FX5311K1 panel back mounting fixers and 2 screws (VESA 75*75).
(P/N:0606010019G)
•Ak1009 Kit- DIN Rail mounting kit(P/N:0606010032R)
5

FabiaTech Corporation
6

FabiaTech Corporation
Chapter2HardwareInstallation
This chapter introduces the system connectors & jumper settings, and guides you to
apply them for field application.
BeforeInstallation
Before installing the system, make sure to follow the descriptions below.
1. Before removing the cover, shut down the operation System and disconnect
power switch off and unplug AC-to DC Adapter cable.
2. If installing connectors, Compact Flash, and hard disk, make sure that the
power is disconnected or power switch off. Otherwise, this may damage the
system.
3. The ESD (Electricity Static Discharge) created from human body may do
damage to the board circuit.
7

FabiaTech Corporation
¾Removing Covers –Installing Hardware
On installing optional hardware, remove the covers. The following figures are to
guide how to install CFast modules, SD Card, and PCIe Mini card module to the
FX5206 and how to install the FX5206 fixers. (Please see the spots circled.)
a. Unscrew Bottom cover and Installing CFast, SD and SIM Card
The following figure guide you how to install compact flash onto the FX5206.
a1. Unscrew the Bottom Cover
6#-32
a2. Insert CFast, SD and SIM Card
Note: The SD socket supports up to 32GB SDHC (Class 6).
8

FabiaTech Corporation
b. Installing PCIe Mini Card Module
You may extend additional PCIe mini card module and SIM card to FX5206.
Connect the antenna cable from backside antenna hole to GPRS module and
installing the SIM card to SIM socket. See as following figure and rear pictures.
b1. Installing PCIe Mini Card and SIM card
Note: 1. When installing PCIe GPRS Mini card on FX5206 system these is need
the installing the SIM Card to SIM socket.
2. The insert SIM card into the SIM card socket. Make sure that the SIM
card is properly inserted and that golden contact area on the card is
facing downwards.
b2. Installing Half Size Mini PCIe module kit (Optional)
9

FabiaTech Corporation
c. Installing the universal fixers
Please refer to the down side figure for installing the FX5206 with universal fixers.
c1. FX5311K1 – Panel Back Mounting (VESA Mount 75*75)
c2. AK1009 Din-Rail Kit
M3*P0.5
10

FabiaTech Corporation
¾LED Indicators & I/O Peripheral Connectors
The Power LED has two distinctive statuses: Off for inactive operation and light for
activity. View from the front and back side, If you are connecting the monitor, LAN,
audio, COM and USB to the FX5206. See following figure and a side pictures.
LAN
EAR-PHONEPOWER LED
ANTENNAANTENNA MIC COM
DC12~24V
+-
POWER SWITCH
USB
RESET
DC IN
CRT
11

FabiaTech Corporation
1. A VGA (CRT) connector is provided for VGA signals.
DB15 Signal
1 Red
2 Green
3 Blue
13 Hsync
14 Vsync
12 DDC Data
15 DDC Clock
5 & 10 Digital Ground
6,7,8 Analog Ground
Others Not Used
2. Connecting the COM port
The COM1 (DB9) is designed for multiple proposes, It’s can select RS-232/422/485 by
BIOS setting. The following tables show the signal connections of connector.
DB9 RS-232 RS-422
RS-485
1 -DCD
6 -DSR
2 RXD RX- 485-
7 -RTS TX-
3 -TXD RX+ 485+
8 -CTS TX+
4 -DTR
9 -RI/5Vor 12V
5 Ground
Metal Case Ground
3. Connecting the LAN port
The RJ45 connector with 2 LED’s for LAN. The right side LED (orange) indicates data
is being accessed and the left side LED (green) indicates on-line status. (On
indicates on-line and off indicates off-line)
RJ45 connector
RJ45
LAN RJ45 LAN
1 TPTX+ 5 TPTX1-
2 TPTX - 6 TPRX -
3 TPRX+ 7 TPRX1+
4 TPTX1+ 8 TPTRX- 1
(Front View)
8
12

FabiaTech Corporation
4. Connecting the USB Ports
The FX5206 supports a three port USB connector. Any USB device can be attached
to USB ports with plug-and-play supported.
USB#1~4 Signal
Pin 1 USBV
Pin 2 USBD-
Pin 3 USBD+
Pin 4 USBG
14
(Front View)
5. Connecting the Audio Microphone In, Earphone-out
EAR-Phone
Mic-In
13

FabiaTech Corporation
¾Connecting the DC Power and Power Switch
Power is supplied through an external power DC In. See following figure and a side
pictures.
1. DC Power Connector: Use external 2-pin apartable terminal block.
DC IN 12V~24V
-
+
Terminal Block
DC +12V~+24V, 25VA
minimum
2. Power Switch: The Power Switch controls the main power switch, plugging DC
into DC power connector then turn on the Power Switch, when you final
installed system hardware device.
OFF
ON
Power Switch: On/Off
3. Reset Push Button
The FX5206 has a push button switcher for system reset; Push and release the
button will cause hardware reset of FX5206 and restart system booting.
Reset Push Button: Restart
14

FabiaTech Corporation
15
¾Jumper Setting
The JP1 is select RS485 terminator resistor for COM1, and J3 is used to connect an
external battery.
JP1
J3
J3: external battery
You can pull plug external battery to clear CMOS data. The CMOS stores
information like system date, time, boot up device, password, IRQ… which are set
up with the BIOS. To clear the CMOS, pull the CMOS battery plug for at last 30
seconds to reset CMOS.
JP1: RS-485 Terminator Setting
JP1
RS-485
Terminator Disabled
Factory Preset
1 2
RS-485
Terminator Enabled
1
2
﹣﹢