fantastic furniture GEO 16 CUBE User manual

Assembly Instructions
BOOKCASE 16 CUBE
GEO

Page 2
2
3
56
Read Instructions carefully.
Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
W
A
R
N
N
G
WARNING
Check no parts are missing.
4
fully tighten screws (leave slightly
loose).When the item is fully assembled
tighten the screws - but do not over tighten.
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
If glue is required DO NOT set until you are
certain that the parts belong together.

Page 3
What You Need
To Assemble The Body
Top Panel
(P1)
Right Side
Panel
(P3)
Left Side
Panel
(P2)
Shelf Panel
(P5)
Shelf Panel
(P7)
Shelf Panel
(P6)
Divider
(P9)
Divider
(P9)
Divider
(P9)
Divider
(P9)
Divider
(P8)
Divider
(P8)
Divider
(P8)
Divider
(P8)
Divider
(P8)
Divider
(P8)
Divider
(P8)
Divider
(P8)
Bottom Panel
(P4)
Back
Panel
(P10)
Back
Panel
(P10)
Back
Panel
(P10)
Back
Panel
(P10)
(Tools not provided)
Flat BladeScrewdriver
Phillips Head Screwdriver
Mallet
18 x Long Dowels
(H1)
10 x Cam Bolts
(H3)
10 x Cam Nuts
(H4)
Please make sure you have all these parts before you start.
32 x Short Dowels
(H2)
4 x Inside
Hexagonal Bolts
(H5)
4 x Covers
(H6)
1
x Allen Key
(H7)
1 x Screw
(H8) (H9) (H10)
1 x Safety Strap 2 x Washers
1x Safety Strap Set
8 x Wedges
(H11)
8 x Screws
(H12)

Page 4
H1
H3
H3
H3
H1
H1 H1
H1
H1
Step 1
You will need:
Step 2
You will need:
18 x Long Dowels
(H1)
(P5)
(P8)
(P8)
(P8)
(P8)
(P8)
(P8)
(P1)
(P2)
(P3)
(P7)
(P6)
H1
H1
H1
H1
H1
H1
10 x Cam Bolts
(H3)
Connect Shelf Panels (P5,P6,P7) with Dividers (P8),
using 18 x Long Dowels (H1).
Hole
Groove
Groove
H3
H3
H3
H3
H3
H3
H3
Attach 10 × Cam Bolts (H3) into Top Panel (P1) and Side Panels (P2,P3) as shown.
Groove
Hole
Hole
Hole
Hole
Groove
Hole

Page 5
6 x Short Dowels
(H2)
Step 4
You will need:
3 x Cam Nuts
(H4)
Insert 6 x Short Dowels (H2) into Shelf Panels (P5) and (P6,P7).
Insert 3 x Cam Nuts (H4) into the holes of Shelf Panels (P5) and (P6,P7).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Side Panel (P2) into place and tighten the cam nuts.
H2
H2
H2
H2
H2
H2
H4
H4
H4
(P5)
(P2)
(P7)
(P6)
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
Step 3
(P5)
(P8)
(P8)
(P9)
(P9)
(P9)
(P9)
(P7)
(P6)
Push Dividers (P8) and (P9) into place.

Page 6
6 x Short Dowels
(H2)
Step 5
You will need:
3 x Cam Nuts
(H4)
Insert 6 x Short Dowels (H2) into Shelf Panels (P5) and (P6,P7) .
Insert 3 x Cam Nuts (H4) into the holes of Shelf Panels (P5) and (P6,P7) .
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Side Panel (P3) into place and tighten the cam nuts.
H2
H2
H2
H2
H4
H4
H4
H2
H2
(P5)
(P2)
(P3)
(P7)
(P6)
Step 6
Slide 4 × Back Panels (P10) into the groove.
(P10)
(P10)
(P10)
(P10)
(P2)
(P3)

Page 7
10 x Short Dowels
(H2)
Step 7
You will need:
4 x Cam Nuts
(H4)
4
x Covers
(H6)
Insert 10 x Short Dowels (H2) into Top Panel (P1).
Insert 4 x Cam Nuts (H4) into the holes of Side Panels(P2) and (P3).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Top Panel (P1) into place and tighten the cam nuts.
Then seal the holes with 4 x Covers (H6).
(P2)
(P3)
(P3)
H2
H2
CHECK
BACK PANEL
FITS INTO
GROOVE
H2 H2
H2 H2
H2
H2
H4
H4
(P1)
(P1)
H2
H2
H4
H6
H6
H4
10 x Short Dowels
(H2)
Step 8
You will need:
4 x Inside
Hexagonal Bolts
(H5)
1
x Allen Key
(H7)
Insert 10 x Short Dowels (H2) into Bottom Panel (P4).
Push Bottom Panel (P4) into place and attach with
4 x
Inside Hexagonal Bolts (H5).Tighten with Allen Key.
(P2)
(P3)
H2
H5
H5
H5 H7
H5
H2
H2 H2
H2
H2
H2
H2
H2
H2
(P1)
(P4)

Step 9
Page 8
You will need:
8 x Wedges
(H11)
8 x Screws
(H12)
H11
Secure 4 x Back Panel (P10) in place with 8 x Wedges (H11) and 8 x Screws (H12).
H12
H11
H12

You will need:
The job is now complete!
In the interest of our environment
Please dispose of all packaging thoughtfully.
Step 10
Step 11
Attach Safety Strap (H8) to Top Panel (P1) using 1 xScrew (H9) and 1 x Washer (H10) .
Page 9
We strongly advise that you use
the wall safety strap provided to
prevent the unit toppling
Seek advice from a qualified
trades person on how to
attach this safety strap to
your specific wall.
Move the bookcase to the final position. Attach the safety strap to the wall.
Make sure it is firmly attached and make sure it is snug fit.
1 x Safety Strap
(H8)
1 x Screw
(H9)
1 x Washer
(H10)
H8
H9
H10
Screw
Wall plug
You will need:
Screw and Wall Plug
which are not provided.
Please use appropriate
fixtures for your wall.
1 x Washer
(H10)
H10