fantastic furniture Amirah Dresser User manual

fantasticfurniture.com.au
Amirah
Dresser
Version 1.2

Page 2
fantasticfurniture.com.au
We're thrilled you've chosen Fantastic Furniture
to help create a home you'll love!
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
Looks like you've found
your Fantastic!
WARNING: ENSURE THE WALL STRAP IS
ATTACHED TO AVOID SERIOUS INJURY
To avoid the risks of injury, this product has been provided with wall
straps to prevent toppling. We strongly recommend that this product
is permanently fixed to the wall or other suitable surface. Fixing
devices are not included since different surface materials require
different attachments. Please seek professional advice if you are in
doubt of what fixing device to use.
!
!WARNING: WEIGHT LIMIT ON TOP IS 80kg.
WARNING: WEIGHT PLACED IN DRAWER NOT TO
EXCEED 10KG.
WARNING: WEIGHT ON INTERNAL SHELF NOT TO
EXCEED 20KG.

! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most commom mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasterners. Check the product care label or
website for product care instructions.
! If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Read through the instructions carefully
before you begin.
Make sure you have all the required tools.
Never use power tools unless instructed.
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
Page 3
fantasticfurniture.com.au
Useful information
Assembly checklist

What you need
to assemble the product
Other tools you need
Phillips head screwdriver, soft headed
mallet.
Parts list
Top Panel (P1);
Left Panel (P2);
Right Panel (P3);
Center Panel (P4);
Shelf Panel (P5);
Door (P6);
Bottom Panel (P7);
Back Plinth Panel (P8);
Front Plinth Panel (P9);
4 x Drawer Back Panel (P10);
4 x Drawer Left Panel (P11);
4 x Drawer Right Panel (P12);
4 x Drawer Front Panel (P13);
4 x Drawer Bottom Panel (P14);
Right Back Panel (P15);
Left Back Panel (P16).
16 x 38mm
Screws (H4)
22 x Cam Nuts
(H2)
24 x Wood
Dowels (H3)
52 x 12mm
Screws (H5)
5 x 22 Screws
(H6)
Page 4
fantasticfurniture.com.au
5 x Rhinestone
Handles (H7)
2 x Hinges
(H13)
1 x L-Bracket
(H11)
4 x Metal Shelf
Support (H12)
2 x Wall Straps
(H14)
Top Panel
(P1)
Left Panel
(P2)
Right Panel
(P3)
Center Panel
(P4)
Shelf Panel
(P5)
Door
(P6)
Bottom Panel
(P7)
Front Plinth
Panel (P9)
Back Plinth
Panel (P8)
Drawer Back
Panel (P10)
Drawer Left
Panel (P11)
Drawer Right
Panel (P12)
Drawer Front
Panel (P13)
Drawer Bottom
Panel (P14)
Back
Panel
(P16)
Back
Panel
(P15)
Hardware pack
22 x Cam Bolt
(H1)
2 x 45mm
Screws (H8)
10 x 16mm
Screws (H10)
4 x Panel
Runner R
(H17)
4 x Panel
Runner L
(H18)
4 x Drawer
Runner L 14"
(H15)
4 x Drawer
Runner R 14"
(H16)
2 x Washers
(H9)

You will need
Prepare the frame:
Insert 10 x cam nuts (H2) into panels (P2), (P3), (P4) & (P7). Rotate the cam nuts so the
arrows point towards the incoming bolt.
Insert 12 x dowels (H3) into panels (P2), (P3), (P4) & (P7) by hand or gently using a soft
headed mallet.
Screw 14 x cam bolts (H1) into panels (P1), (P2) & (P3) using
a phillips head screwdriver.
12 x Wood Dowels
(H3)
Page 5
fantasticfurniture.com.au
10 x Cam Nuts
(H2)
14 x Cam Bolts
(H1)
Phillips Head
Screwdriver
Soft Headed
Mallet
Step 1
H2
H2
H2
H2
H2
H2
H2
H2
H2
H2
H1
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H1
P2
P3
P1
P4
P7
H3
H3
H1
H1
H1
H1
H1
H1
H1
H1
H1
H1
H1
H1
H1
H2

Insert 12 x cam nuts (H2) into panels (P8), (P9), (P11) & (P12). Rotate the cam nuts so the
arrows point towards the incoming bolt.
Insert 12 x dowels (H3) into panels (P8), (P9), (P11) & (P2) by hand or gently using a soft
head mallet.
Screw 8 x cam bolts (H1) into panels (P13) using a phillips head screwdriver.
You will need
Page 6
fantasticfurniture.com.au
8 x Cam Bolts
(H1)
12 x Wood Dowels
(H3)
12 x Cam Nuts
(H2)
Phillips Head
Screwdriver
Soft Headed
Mallet
x 4
pcs
x 4
pcs
x 4
pcs
H1 H3
16 x 38mm
Screws (H4)
You will need
Phillips Head
Screwdriver
4 x 22 Screws
(H6)
4 x Rhinestone
Handles (H7)
Repeat x 4 This is how a cam nut works........
The head of the cam bolt
goes into the open mouth of
the cam nut. You then turn
the cam nut so it tightens
over the bolt.
Lock
H1 H2
Unlock
Step 2
Step 3
P11
P12
P13
P8
P9
H3
H3 H3
H3
H3
H3
H2
H2
H2
H2
H2
H2
H1
P12
P11
P10
P10
P12
P11
P14
P13
H4
H4
H7
H6
Begin assembling the drawers:
To attach panels (P11 & P12) to panel (P10), insert 4 x 38mm screws (H4) and tighten with a phillips head
screwdriver.
Slide in the drawer bottom panel (P14) into the grooves of panels (P11, P12 & P10) with the laminated side
facing up.
Attach the panel (P13) to panel (P11 & P12) and ensure the drawer bottom panel (P14) slides into the groove on
panel (P13).
Turn the cam nuts on panels (P11 & P12) clockwise with a phillips head screwdriver to lock in
position.
Attach the handle (H7) to panel (P13) with 1 x 22mm screw (H6) using a phillips head screwdriver.
Repeat this process for the remaining drawers.
Laminated
Side
H2
H1
H2
Laminated
Side

Attach the drawer runner L (H15) and the drawer runner R (H16) to the underside of the
drawer with 6 x 12mm screws (H5) using a phillips head screwdriver.
Repeat this process for the other 3 drawers.
Step 5
Phillips Head
Screwdriver
24 x 12mm
Screws (H5)
You will need
4 x Drawer
Runners L
(H15)
Phillips Head
Screwdriver
24 x 12mm
Screws (H5)
You will need
4 x Panel
Runners R (H17)
Attach 4 x panel runners R (H17) to the right side panel (P4) with 3 x 12mm
screws (H5) using a phillips head screwdriver.
Attach 4 x panel runners L (H18) to the left side panel (P2) with 3 x 12mm
screws (H5) using a phillips head screwdriver.
Page 7
fantasticfurniture.com.au
Step 4
Repeat x 4
H18
H17
P2
P4
4 x Drawer
Runners R
(H16)
4 x Panel
Runners L (H18)
H17
H5
H18
H5
H17
H17
H17
H18
H18
H18
H15
H16
P10
P12
P12
P14
P14
H16
H5
H5
H5

Page 8
fantasticfurniture.com.au
Attach panels (P7), (P8) to panel (P2) by aligning the dowels & cam bolts with the
corresponding holes.
Turn the cam nut on panels (P7), (P8) clockwise motion with a phillips head screwdriver to
lock in position.
Step 7
You will need
Phillips Head
Screwdriver
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
Step 6
P2
P7
P8
You will need
Phillips Head
Screwdriver
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
Attach panel (P9) to panel (P2) by aligning the dowels & cam bolts with the corresponding
holes.
Turn the cam nut on panel (P9) clockwise motion with a phillips head screwdriver to lock in
position.
P9

Page 9
fantasticfmurniture.com.au
Step 9
Step 8
Attach panel (P3) to panels (P7), (P8) & (P9).
Turn the cam nut on panels (P7), (P8) & (P9) clockwise motion with a phillips
head screwdriver to lock in position.
P9
P7
P8 P3
You will need
Phillips Head
Screwdriver
P9
Begin with frame lying on its front on a soft surface.
Attach panel (P4) to panel (P7) by aligning the dowels to the holes.
Insert 2 x 45mm screws (H8) using a phillips head screwdriver.
Secure 1 x L-bracket to (P7) & (P9) with 4 x 12mm screws (H5) using a phillips
head screwdriver.
Phillips Head
Screwdriver
4 x 12mm
Screws (H5)
You will need
2 x 45mm
Screws (H8)
1 x L-Bracket
(H11)
P4
P8
P9
P7
H11
H8
H8
H11 H5
Back
Front
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.

Step 10
Page 10
fantasticfurniture.com.au
Step 11
Slide panels (P15) & (P16) into the grooves in panels (P2), (P3) & (P4) with the
laminated side facing the front for panel (P15).
P2
P3
P16
P15
P4
Front
Laminated Side
Warning Label
at the back
and top of unit
Attach panel (P1) to panels (P2), (P3) & (P4) by aligning the dowels and cam bolts to the
holes.
Ensure the back panels (P16) & (P15) slide in the groove of panel (P1).
Turn the cam nuts on panels (P2), (P3) & (P4) clockwise with a phillips head
screwdriver to lock in position.
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
P1
P2
P3
P4
You will need
Phillips Head
Screwdriver

Attach the door (P6) to side panel (P3) by attaching the hinges to panel (P3)
with 4 x 16mm screws (H10) using a philips head screwdriver.
Step 12
Page 11
fantasticfurniture.com.au
P6
H13
H13
Step 13
Phillips Head
Screwdriver
4 x 16mm Screws
(H10)
You will need
Attach 2 x hinges (H13) to door panel (P6) with 4 x 16mm screws (H10) using a
phillips head screwdriver.
2 x Hinges
(H13)
H10
H10
Phillips Head
Screwdriver
4 x 16mm Screws
(H10)
You will need
P6
H13
H13
H13
H10

Put in the drawers one at a time, starting at the bottom.
Page 12
fantasticfurniture.com.au
Step 14
Step 15
H12
Attach the handle (H7) to panel (P6) with 1 x 22mm screw (H6) using a phillips
head screwdriver.
Insert 4 x shelf support (H12) into desired holes in panels (P3) & (P4).
Place adjustable shelf (P5) onto shelf support.
1 x 22mm Screw
(H6)
1 x Rhinestone
Handle (H7)
You will need
4 x Metal Shelf
Support (H12)
Phillips Head
Screwdriver
P5
P6
H6
H7
P5
P4
P3

Step 16
TO ADJUST THE DOORS TO MAKE THE GAPS MORE
EVEN (OPTIONAL).
Step 16a
Adjust the door move in
or out a little.
Step 16b
Move Door In
Step 16c
Move Door Out
Door : The door should
move in a little.
Loosen the screw indicated a
little, adjust the hinge to right
position, then tighten the
screw. Push the hinge back a
little.
Push the hinge forward a
little.
Step 16d
To adjust the gap
between door and side.
Step 16e
Move Door Right
Step 16f
Move Door Left
Loosen or tighten the screw
indicated a little to adjust
the gap between door and
leg.
Turn the screw clockwise
a little as shown to make
the gap big.
Door : The door should
move out a little.
Top
panel
Turn the screw
counterclockwise a little
as shown to make the gap
small.
Page 13
fantasticfurniture.com.au
Top
panel
Door
Top panel
Door
Top panel
Door
Top panel
Top panel
Door
Top panel
Door
Top panel
Door
Top panel
Door
Top panel
Door

We strongly advise that
you use the wall safety
strap provided to prevent
the unit toppling over.
Step 17
Page 14
fantasticfurniture.com.au
Job Complete!
In the interest of our environment please dispose of all packaging
thoughtfully.
Attach wall fixing strap to panel (P1) with 2 x 16mm screws (H10) and 2 x washers (H9) using
a phillips head screwdriver. There are pre-drilled holes on the bottom of panel (P1) to insert
the screws.
Move the chest to the final position.
Attach the safety strap to the wall. Make sure it is firmly attached and make sure it is a
snug fit.
The screws and wall plug are not provided. Please use appropriate fixtures
for your wall.
Seek advice from a qualified trades person on how to attach these wall
straps to your specific wall.
2 x Wall
Straps (H14)
You will need
2 x Washers
(H9)
Phillips Head
Screwdriver
2 x 16mm
Screws (H10)
P1
H14
H14
H14 H9
H10
P1
Pre-Drilled
Hole