fantastic furniture Hamilton Display Cabinet 1 Drawer User manual

Hamilton
Display Cabinet 1 Drawer
fantasticfurniture.com.au
Version 1.0

fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 20kgs /Shelf.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
Page 2
Glass should always be handled with care.
cause glass to break. This glass is designed to break into small,
relatively harmless pieces and not sharp fragments. Avoid
placing hot or cold items directly onto the table unless using a
thick insulation material such as placemats or coasters.
Avoid dropping objects onto the glass.
Do not allow hard or pointed objects to come into contact
with the glass. Never use the top area as a chopping surface.
Do not sit or stand on the glass surface.

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
!Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
!The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
!Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
!Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
!Never use any glue until you are certain that the parts belong together.
!Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
!If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
!Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Left Side Panel (P2);
Right Side Panel (P3);
2 x Shelf Panels (P4);
Bottom Shelf Panel (P5);
3 x Back Panels (P6);
Drawer Back Panel (P7);
Rail (P8);Rail (P9);
Left Door (P10);
Right Door (P11);
Drawer Front (P12);
Left Drawer Side (P13);
Right Drawer Side (P14);
Drawer Back (P15);
Drawer Base (P16);
Rail (P17);
Iron Bar (P18);
Hardware pack
Top Panel
(P1)
Shelf Panel
(P4)
Shelf
Panel
(P4)
Left Door
(P10)
Right Door
(P11)
Bottom
Shelf Panel
(P5)
Right Side
Panel (P3)
Left Side
Panel (P2)
3 x Back
Panels
(P6)
Drawer
Back Panel
(P7)
Rail
(P8)
Rail
(P9)
Iron Bar
(P18)
Left
Drawer
Side (P13)
Drawer Front
(P12)
Right
Drawer
Side
(P14)
Drawer
Back (P15)
Rail
(P17)
Drawer
Base
(P16)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Page 4
fantasticfurniture.com.au
DO NOT USE
14 x Dowels
(H1)
5 x Long
Screws
(H2)
36 x Small
Screws
(H5)
1 x CL Runner
Track
(H6)
27 x Cam
Bolts
(H3)
27 x Cam
Nuts
(H4)
1 x CR Runner
Track
(H7)
1 x DL
Runner
(H8)
1x DR
Runner
(H9)
4 x Handles
(H10)
2 x Magnet
Bars
(H17)
4 x Bolts
(H11)
8 x Wedges
(H12)
8 x Screws
(H13)
1 x Magnet
(H14)
2 x Magnet
Screws
(H15)
6 x Hinges
(H16)
2 x Safety
Strap
Screws
(H21)
2 x Safety
Straps
(H20)
4 x Washers
(H22)
4 x Round
Screws
(H18)
4 x Medium
Screws
(H19)

1 x CL Runner
Track (H6)
6 x Small
Screws (H5)
1 x CR Runner
Track (H7)
(P2)
(P18)
(P5)
(P3)
You will need
Step 1
Step 2
You will need
Phillips Head
Screwdriver
Attach 18 x Cam Bolts (H3) to Left & Right Side Panels (P2 & P3) as shown by tightening
with the Phillips Head Screwdriver. Attach 1 x CL Runner Track (H6) to Left Side Panel (P2)
with 3 x Small Screws (H5). Attach 1 x CR Runner Track (H7) to Right Side Panel (P3) with 3 x
Small Screws (H5).
fantasticfurniture.com.au Page 5
18 x Cam Bolts
(H3)
Phillips Head
Screwdriver
CL
CR
H19
H5
H6
H5
H5
H5
H6
H7
H7
4 x Medium
Screws (H19)
Attach Iron Bar (P18) to Bottom Shelf Panel (P5) with 4 x Medium Screws (H19) by
tightening with the Phillips Head Screwdriver.

Step 4
Slide Back Panels (P6x2, P7) into the grooves of Shelf Panels & Rail (P4x2, P5 & P8).
Insert 7 x Dowels (H1) and 9 x Cam Nuts (H4) into Shelf
Panels & Rails (P4x2, P5&P8, P9) as shown. Rotate the nuts so
the arrows point towards the incoming bolts. Attach Shelf Panels &
Rails (P4x2,P5&P8, P9) to Left Side Panel (P2) by tightening all nuts with the Phillips Head
Screwdriver. Attach the end of Iron Bar (P18) to Left Side Panel (P2) with 2 x Round Screws (H18).
9 x Cam Nuts
(H4)
(P2)
(P4)
(P4)
(P4)
(P4)
(P5)
(P6)
(P6)
(P7)
(P8)
(P5)
(P8)
(P9)
(P18)
Step 3
You will need
Phillips Head
Screwdriver
fantasticfurniture.com.au Page 6
7 x Dowels
(H1)
H1
H4
H18
2 x Round
Screws (H18)
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.

Gently stand the unit upright. Slide Back Panel (P6) into the grooves of
Left&Right Side Panels (P2&P3).
Step 5
You will need
Insert 7 x Dowels (H1) and 10 x Cam Nuts (H4)
into Shelf Panels & Rails (P4x2, P5&P8, P9) as shown.
Rotate the nuts so the arrows point towards the
incoming bolts. Attach Right Side Panel (P3)
to Shelf Panels & Rails (P4x2, P5&P8, P9) by tightening
all nuts with the Phillips Head Screwdriver. Attach the end of
Iron Bar (P18) to Right Side Panel (P3) with 2 x Round Screws (H18).
9 x Cam Nuts
(H4)
Phillips Head
Screwdriver
Step 6
(P2)
(P4)
(P4)
(P5)
(P8)
(P9)
(P18)
(P6)
(P3)
(P3)
fantasticfurniture.com.au Page 7
7 x Dowels
(H1)
H1
H4
H18
2 x Round
Screws (H18)

You will need
Phillips Head
Screwdriver
Step 7
You will need
Phillips Head
Screwdriver
Step 8
Attach 4 x Cam Bolts (H3) to Top Panel (P1) by tightening with the Phillips Head Screwdriver.
Attach 1 x Magnet (H14) to Top Panel (P1) with 4 x Magnet Screws (H15).
(P2)
(P1)
(P1)
(P3)
fantasticfurniture.com.au Page 8
4 x Cam Nuts
(H4)
H3
H3
H4
H4
H4
H14
H15
H3
H3
4 x Cam
Bolts (H3)
1 x Magnet
(H14)
2 x Magnet
Screws (H15)
H14
H15
H15
Insert 4 x Cam Nuts (H4) into
Left&Right Side Panels (P2&P3).
Rotate the nuts so the arrows point
towards the incoming bolts. Attach
Top Panel (P1) to Left&Right Side
Panels (P2&P3) by tightening all
nuts with the Phillips Head Screwdriver.

Attach 6 x Hinges (H16) and 2 x Magnet Bars (H17) to Doors (P10, P11) as shown with 14 x
Small Screws (H5) by tightening with the Phillips Head Screwdriver.
Attach Left Door (P10) to
Left Side Panel (P2) and Right
Door (P11) to Right Side Panel
(P3) with 6 xHinges (H16) and
12 x Small Screws (H5) by
tightening with the Phillips
Head Screwdriver. Attach 2 x
Handles (H10) to Doors (P10, P11)
with 2 x Bolts (H11) by tightening
with the Phillips Head Screwdriver.
You will need
Step 9
Phillips Head
Screwdriver
Step 10
You will need
Phillips Head
Screwdriver
(P10)
(P11)
(P11)
(P10)
(P3)
(P2)
fantasticfurniture.com.au Page 9
14 x Small
Screws (H5)
6 x Hinges
(H16)
2 x Magnet
Bars (H17)
H16
H16
H16 H16
H5
H5
H5
H5
H5
H17
H17
H17
H5
H5
H16
H16
H16
H5
H5
H5
H10
H10
H10
H11
H11
H11
H5
H16
H16
H16
H16
H5
H5
H5
12 x Small
Screws (H5)
2 x Handles
(H10)
2 x Bolts
(H11)
Required
Two People

Step 11
You will need
Attach 5 x Cam Bolts (H3) to Drawer Front (P12) by tightening with the Phillips Head Screwdriver.
Step 12
You will need
Step 13
Insert 5 x Cam Nuts (H4) into Left&Right
Drawer Sides & Rail (P13&P14&P17) as shown. Rotate
the cam nuts so the arrows point towards
the incoming cam bolts. Attach Drawer Front (P12)
to Left & Right Drawer Sides & Rail (P13&P14&P17) by
tightening all cam nuts with the Phillips Head Screwdriver.
Slide Drawer Base (P16) into the grooves of Drawer Sides (P13) and (P14) and
Drawer front (P12).
(P12)
(P12)
(P12)
(P13) (P17)
(P13)
(P14)
(P14)
(P16)
fantasticfurniture.com.au Page 10
H3 H3
H3
H3
H3
H4
H4
H4
H4
H4
Phillips Head
Screwdriver
5 x Cam
Bolts (H3)
Phillips Head
Screwdriver
5 x Cam Nuts
(H4)