GF Signet 5090 User manual

Sensor Frequency = ___________________________ Hz
Technical note:
Sensor frequency MUST be greater than 45 Hz for full scale
needle deflection.
3. Calculate the actual max. flow rate in your process line as follows:
Maximum flow rate = Sensor frequency (step 2) ×A-Factor (Section 6)
Maximum Flow Rate = __________________________________
2. Calibration
The 5090/515 flow metering system utilizes the AC signal
amplitude from the 515 sensor to drive the 5090 meter.
The front panel meter movement adjustment (SPAN) is easily
accessed under the removable front window for simple calibration.
A dial kit with six dial ranges, assorted flow unit/multiplier decals,
and dial installation instructions is included for your convenience.
1. Compatible Sensor Wiring
Frequency
counter
Red
Black
10
0
1
2
3
456
7
8
9
GPM
X100
SPAN
Signet Monitor
4. Install the appropriate dial face and flow unit/multiplier decal
for the maximum flow rate (Step 3). Refer to dial installation
instructions included with dial kit.
The dial kit includes the following:
Example: A flow system's maximum flow rate is 18.3 GPM.
The proper dial and flow unit/multiplier decal for this flow system is:
0 - 2 dial + GPM × 10 decal.
5. Disconnect frequency counter.
Access and adjust the "SPAN" potentiometer to match the
calculated maximum flow rate from Step 3.
After adjustment, calibration is complete.
5090
Rotor
w/magnets
Black
Red
515 Circuit
Shield
SPAN
0
1
23 8
6 7
5
4
9
X 100
GPM
10
SPAN
Signet Monitor
6 Dials:
0-2
0-4
0-6
0-8
0-10
0-100
Assorted Unit and Multiplier Decals:
X 10
X 100
X 1,000
X 10,000
LPM
x 1,000
GPM
x 10
m
3
/h
SPAN
0
1
2
3
8
6
7
5
4
9
10
SPAN
0
1
2
SPAN
0
1
2
SPAN
0
1
2
3
8
6
7
5
4
9
10
Signet 5090 Flow Monitor
Technical Notes:
• Remove terminal block for easy wiring (Fig. 1)
• Maintain cable shield through cable splice.
• Route sensor cable away from AC power lines.
• Use 2-conductor shielded cable for sensor cable extension up
to 61 m (200 ft).
English
Red
Blk
Shld
Sensor
Input
515
Black (AC signal out)
Red (AC signal out)
Silver (shield)
5090 Rear
Terminal
Connection
Red
Blk
Shld
Sensor
Input
Red
Blk
Shld
Sensor
Input
LISTED
77CJ
U
L
Fig. 1
*3-5090.090-1*
3-5090.090-1 Rev. K 08/13
Procedure
1. Induce the maximum (stable) flow rate in your process line.
2. Using the frequency counter, monitor and record the 515
sensor frequency output:
Equipment Required
• Frequency counter
• Signet 515 Sensor installed in process line
• Standard and phillips head screwdriver

2Signet 5075 Flow Monitor
SIDE VIEW
Mounting Clamp (2 ea.)
Optional Splashproof Rear Cover
88 mm
(3.5 in.)
Mounting Panel
Panel
Gasket
91 mm
(3.6 in.)
76 mm (3 in.)
88 mm (3.5 in.)
96 mm (3.8 in.)
3. Parts and Accessories
There are no user replaceable components in the 5090.
Unauthorized repair attempts may void warranty.
• Front snap-on bezel, 3-5000.525 (code 198 840 226)
• Assorted flow unit/multiplier decal sheet,
3-5090.611 (code 198 840 228)
• 5090 Instruction sheet, 3-5090.090-1
(code 198 869 912)
4. Specifications
General
Sensor compatibility: Signet 515 only
Minimum full scale range: 7 fps
• Weight:Approximately 450 g (16 oz.)
Display:
• Type: Taut-band suspension meter movement, 250° deflection
(not suitable for prolonged exposure to vibration)
• Repeatability: ±1% of full scale
Materials
• Case: ABS plastic
• Panel and case gasket: Neoprene
• Window: Hard-coated polycarbonate
5. Maintenance
Never wipe the front window with static retentive cloths such as wool or polyester which may induce a static charge. If a static charge
develops on the window, the indication needle may appear erratic or non-functional. When this occurs, clean the front window with an
anti-static cloth, or a soft cotton cloth and anti-static spray or a mild liquid soap solution to remove the static charge.
Clean the instrument case and front panel with a soft cotton cloth dampened with a mild liquid soap solution.
SPAN
0
1
2
3
8
6
7
5
4
9
X 100
GPM
10
96 mm
(3.8 in.)
Front View
96 mm (3.8 in.)
Signet Monitor
Splashproof rear cover
3-5000.395
(code 198 840 227)
92 x 92 mm
(3.62 x 3.62 in.)
Panel cutout
5 x 5 inch adapter plate for
retrofitting Signet 500 series
3-5000.399 (code 198 840 224)
Optional surface
mount bracket
3-5000.598
(code 198 840 225)
Electrical
Power Requirements: None
Environmental
Operating temperature: -10 °C to 65 °C (14 °F to 149 °F)
Storage temperature: -15 °C to 80 °C (5 °F to 176 °F)
Relative humidity: 0 to 95%, non-condensing
Enclosure:
• Rating: NEMA 4X/IP65 front
• Dimensions: 1/4 DIN, 96 x 96 x 88 mm (3.8 x 3.8 x 3.5 in.)
Standards and Approvals
• UL, CUL
• RoHS Compliant
• Manufactured under ISO 9001 for Quality,
ISO 14001 for Environmental Management and
OHSAS 18001 for Occupational Health and Safety.
China RoHS (Go to www.gfsignet.com for details)
Dimensions

3
Signet 5090 Flow Monitor
6. Signet 515 Flow Sensor A-Factors
-------------- A-FACTORS ----------------
PIPE
SIZE SIGNET FITTING ------------------- 1 Hz = -------------------
U.S. GPM LPM m3/h
SCH 80 PVC TEES FOR SCH 80 PVC PIPE
1/2 IN. PV8T005 0.1250 0.4729 0.0284
3/4 IN. PV8T007 0.2328 0.8812 0.0529
1 IN. PV8T010 0.3435 1.3002 0.0780
1 1/4 IN. PV8T012 0.7195 2.7233 0.1634
1 1/2 IN. PV8T015 1.0242 3.8767 0.2326
2 IN. PV8T020 1.8473 6.9920 0.4195
2 1/2 IN. PV8T025 2.7481 10.4016 0.6241
3 IN. PV8T030 4.4310 16.7714 1.0063
4 IN. PV8T040 7.8681 29.7807 1.7868
SCH 80 CPVC TEES FOR SCH 80 CPVC PIPE
1/2 IN. CPV8T005 0.1250 0.4729 0.0284
3/4 IN. CPV8T007 0.2328 0.8812 0.0529
1 IN. CPV8T010 0.3435 1.3002 0.0780
1 1/4 IN. CPV8T012 0.7195 2.7233 0.1634
1 1/2 IN. CPV8T015 1.0242 3.8767 0.2326
SCH 80 PVC SADDLES FOR SCH 80 PVC PIPE
2 IN. PV8S020 1.8473 6.9920 0.4195
2 1/2 IN. PV8S025 2.7481 10.4016 0.6241
3 IN. PV8S030 4.4310 16.7714 1.0063
4 IN. PV8S040 7.8681 29.7807 1.7868
6 IN. PV8S060 14.4152 54.5614 3.2737
8 IN. PV8S080 25.3115 95.8039 5.7482
SCH 80 PVC SADDLE ON SCH 40 PVC PIPE
2 IN. PV8S020 2.1938 8.3035 0.4982
2 1/2 IN. PV8S025 3.1789 12.0321 0.7219
3 IN. PV8S030 4.7477 17.9702 1.0782
4 IN. PV8S040 8.9177 33.7536 2.0252
6 IN. PV8S060 16.0871 60.8897 3.6534
8 IN. PV8S080 27.8714 105.4932 6.3296
CARBON STEEL TEES ON SCH 40 PIPE
1/2 IN. CS4T005 0.1621 0.6134 0.0368
3/4 IN. CS4T007 0.2829 1.0709 0.0643
1 IN. CS4T010 0.4251 1.6091 0.0965
1 1/4 IN. CS4T012 0.9892 3.7442 0.2246
1 1/2 IN. CS4T015 1.3230 5.0077 0.3005
2 IN. CS4T020 2.2416 8.4845 0.5091
STAINLESS STEEL TEES ON SCH 40 PIPE
1/2 IN. CR4T005 0.1671 0.6327 0.0380
3/4 IN. CR4T007 0.2961 1.1209 0.0673
1 IN. CR4T010 0.4719 1.7862 0.1072
1 1/4 IN. CR4T012 0.9691 3.6682 0.2201
1 1/2 IN. CR4T015 1.4848 5.6199 0.3372
2 IN. CR4T020 2.6906 10.1839 0.6110
GALVANIZED IRON TEES ON SCH 40 PIPE
1 IN. IR4T010 0.5740 2.1724 0.1303
1 1/4 IN. IR4T012 0.9527 3.6060 0.2164
1 1/2 IN. IR4T015 1.2851 4.8642 0.2919
2 IN. IR4T020 2.0367 7.7089 0.4625
BRONZE TEES ON SCH 40 PIPE
1 IN. BR4T010 0.5740 2.1724 0.1303
1 1/4 IN. BR4T012 0.9527 3.6060 0.2164
1 1/2 IN. BR4T015 1.2851 4.8642 0.2919
2 IN. BR4T020 2.0367 7.7089 0.4625
----------------- A-FACTORS -------------------
PIPE
SIZE SIGNET FITTING ---------------------- 1 Hz = -----------------------
U.S. GPM LPM m3/h
COPPER TEE FITTINGS ON COPPER PIPE
1/2 IN.SK K CUKT005 0.1354 0.5124 0.0307
1/2 IN. SK L 0.1448 0.5480 0.0329
3/4 IN.SK K CUKT007 0.2828 1.0704 0.0642
3/4 IN. SK L 0.3140 1.1885 0.0713
1 IN.SK K CUKT010 0.4718 1.7857 0.1071
1 IN. SK L 0.5007 1.8950 0.1137
1 1/4 IN.SK K CUKT012 0.6801 2.5743 0.1545
1 1/4 IN. SK L 0.7022 2.6577 0.1595
1 1/2 IN.SK K CUKT015 1.0533 3.9869 0.2392
1 1/2 IN. SK L 1.0878 4.1171 0.2470
2 IN.SK K CUKT020 2.0429 7.7325 0.4639
2 IN. SK L 2.0975 7.9391 0.4763
STAINLESS STEEL WELDOLETS ON SCH 40 PIPE
2 1/2 IN. CR4W025 3.1915 12.0798 0.7248
3 IN. CR4W030 4.9302 18.6606 1.1196
4 IN. CR4W040 8.6207 32.6293 1.9578
5 IN. CR4W050 11.4068 43.1749 2.5905
6 IN. CR4W060 16.2602 61.5447 3.6927
8 IN. CR4W080 28.1690 106.6197 6.3972
10 IN. CR4W100 44.4444 168.2222 10.0933
12 IN. CR4W120 62.5000 236.5625 14.1938
CARBON STEEL WELDOLETS ON SCH 40 PIPE
2 1/2 IN. CS4W025 3.1915 12.0798 0.7248
3 IN. CS4W030 4.9302 18.6606 1.1196
4 IN. CS4W040 8.6207 32.6293 1.9578
5 IN. CS4W050 11.4068 43.1749 2.5905
6 IN. CS4W060 16.2602 61.5447 3.6927
8 IN. CS4W080 28.1690 106.6197 6.3972
10 IN. CS4W100 44.4444 168.2222 10.0933
12 IN. CS4W120 62.5000 236.5625 14.1938
COPPER/BRONZE BRAZOLETS ON SCH 40 PIPE
2 1/2 IN. BR4B025 3.1915 12.0798 0.7248
3 IN. BR4B030 4.9302 18.6606 1.1196
4 IN. BR4B040 8.6207 32.6293 1.9578
5 IN. BR4B050 11.4068 43.1749 2.5905
6 IN. BR4B060 16.2602 61.5447 3.6927
8 IN. BR4B080 28.1690 106.6197 6.3972
10 IN. BR4B100 44.4444 168.2222 10.0933
12 IN. BR4B120 62.5000 236.5625 14.1938
SCH 80 IRON SADDLES ON SCH 80 PIPE
2 IN. IR8S020 1.8541 7.0179 0.4211
2 1/2 IN. IR8S025 2.7003 10.2205 0.6132
3 IN. IR8S030 4.4709 16.9225 1.0154
4 IN. IR8S040 7.8329 29.6475 1.7789
5 IN. IR8S050 10.2389 38.7543 2.3253
6 IN. IR8S060 14.6699 55.5257 3.3315
8 IN. IR8S080 25.7511 97.4678 5.8481
10 IN. IR8S100 39.2157 148.4314 8.9059
12 IN. IR8S120 56.6038 214.2453 12.8547
SCH 80 IRON SADDLE ON SCH 40 PIPE
2 IN. IR8S020 2.2371 8.4676 0.5081
2 1/2 IN. IR8S025 3.1915 12.0798 0.7248
3 IN. IR8S030 5.0042 18.9408 1.1364
4 IN. IR8S040 8.7591 33.1533 1.9892
5 IN. IR8S050 11.2570 42.6079 2.5565
6 IN. IR8S060 15.9574 60.3989 3.6239
8 IN. IR8S080 28.1690 106.6197 6.3972
10 IN. IR8S100 44.4444 168.2222 10.0933
12 IN. IR8S120 62.5000 236.5625 14.1938

------------------------------ A-FACTORS -------------------------------
PIPE
SIZE SIGNET FITTING ---------------------------------- 1 Hz = ------------------------------------
U.S. GPM LPM m3/h CODE
POLYPROPYLENE FITTINGS (DIN/ISO AND BS AND ANSI)
DN 15 PPMT005 0.1246 0.4716 0.0283 727 310 036
DN 20 PPMT007 0.2165 0.8196 0.0492 727 310 037
DN 25 PPMT010 0.4250 1.6086 0.0965 727 310 038
DN 32 PPMT012 0.7182 2.7185 0.1631 727 310 039
DN 40 PPMT015 1.1704 4.4299 0.2658 727 310 040
DN 50 PPMT020 2.0273 7.6734 0.4604 727 310 041
PVDF FITTINGS (DIN/ISO AND BS AND ANSI)
DN 15 SFMT005 0.1426 0.5396 0.0324 735 310 036
DN 20 SFMT007 0.2630 0.9954 0.0597 735 310 037
DN 25 SFMT010 0.4389 1.6613 0.0997 735 310 038
DN 32 SFMT012 0.7567 2.8640 0.1718 735 310 039
DN 40 SFMT015 1.3796 5.2219 0.3133 735 310 040
DN 50 SFMT020 2.3159 8.7655 0.5259 735 310 041
11/16/2000
DN 15 PVMT005 0.1234 0.4671 0.0280 198 150 480
DN 20 PVMT007 0.2471 0.9352 0.0561 198 150 481
DN 25 PVMT010 0.4037 1.5279 0.0917 198 150 482
DN 32 PVMT012 0.7048 2.6679 0.1601 198 150 483
DN 40 PVMT015 1.1571 4.3796 0.2628 198 150 484
DN 50 PVMT020 2.0168 7.6336 0.4580 198 150 485
DN 65 PVMS025 3.4312 12.9870 0.7792 198 150 538
DN 80 PVMS030 4.8037 18.1818 1.0909 198 150 539
DN 100 PVMS040 7.3731 27.9071 1.6744 198 150 540
DN 150 PVMS060 14.6778 55.5556 3.3333 198 150 543
DN 200 PVMS080 29.3556 111.1111 6.6667 198 150 545
A-Factor Conversion Formulas:
1 U.S. gallon =
0.83267 Imperial gallon
0.003785 Cubic meters
0.000003069 Acre feet
8.3454 Pounds of water
A-Factors for DIN Pipes
Georg Fischer Signet LLC, 3401 Aero Jet Avenue, El Monte, CA 91731-2882 U.S.A. • Tel. [phone] • Fax [phone]
For Worldwide Sales and Service, visit our website: www.gfsignet.com • Or call (in the U.S.): [phone]
For the most up-to-date information, please refer to our website at www.gfsignet.com
3-5090.090-1 Rev. K 08/13 English © Georg Fischer Signet LLC 2013