Hameg HMO3000 Series Instruction manual

Mixed Signal Oscilloscopes
300 MHz
|
400 MHz
|
500 MHz
HMO3000 Series

More information | www.hameg.com 3
up to 500 MHz…
High sensitivity, multi-functionality and a great price –
that‘s what distinguishes the HAMEG HMO3000 oscilloscope series.
Key facts
❙ 4 GSa /s real time, low noise fl ash A /D converter
❙8 MPts memory, zoom up to 200,000:1
❙MSO functionality included as standard
(HO3508/HO3516 logic probe with 8/16 channels required)
❙Automatically or manually adjustable memory depth
❙Vertical sensitivity up to 1mV/div.
❙Trigger modes: slope (A/B), pulse width, video, logic,
serial buses (optional), hold-off
❙Serial bus trigger and hardware accelerated decode incl. list view.
Options: I2C + SPI + UART/RS-232 (HOO10/HOO11), CAN + LIN (HOO12)
❙28 auto-measurement parameters plus statistics, formula editor, ratio cursor
❙6-digit hardware counter
❙FFT up to 64 kPts (dBm, dBV, Vrms)
❙Pass/fail test based on masks
❙ Automatic search for user-de ned events
❙ Display: 12 div. x-axis, 20 div. y-axis (Virtual Screen)
❙ 2x USB for mass storage, Ethernet/USB dual interface for remote control
HMO 3004 Series, 500MHz with 4 Channels
Intelligent user interface
To optimize the screen
display, the instrument
shows and hides menus
Precise signal analysis
4 GSamples/s sampling rate
8 MPoints memory
Video
Setup
Intuitive, multi-lingual
user menu
FFT
Superb FFT
functionality
Help
Context-sensitive help
Quick view
At the push of a button
the 16 most important
values of the measured
signal are permanently
updated and displayed
Fan
Maximum noise reduction by
temperature-controlled fan
Zoom
Memory zoom up to
200,000 : 1
Analog channels
Vertical sensitivity of up to
1mV/div.
Bus signal source
To create SPI, I2C, UART
and counter test-signals
Standard MSO functionality
Analyze analog channels plus up to
an additional 16 digital channels
Math
Wide range of programmable
math functions
Display
Superb 16.5 cm (6.5”) LED-backlit
TFT display
2 HAMEG INSTRUMENTS | HMO3000 SERIES
HMO3000 product video:
Scan, click or go to
http://youtube.com/
HAMEGcom
HMO3000 Series
Application How the HAMEG HMO3000 meets your needs
Engineering lab ❙Adjustable memory depth
❙Advanced math functions available as standard, math on math possible
❙Automeasurement for 28 user-defined parameters
❙Memory zoom function up to 200,000:1
Analog
circuit design
❙ Low-noise amplifier and A/D converter
❙1 mV/div. sensitivity
❙ 50 Ω/1 MΩ input impedance, switchable
❙Bandwidth upgrades via software options
Embedded
debugging
❙ Mixed signal option (MSO) with 16 logic channels
❙Serial bus trigger and hardware-accelerated decode
❙6-digit hardware counter
❙Superb FFT functionality
Production
environment
❙Remote control for automated data acquisition
❙Pass/fail tests based on user-defined masks with error signal output
❙Automatic signal measurement at the push of a button
❙USB/RS-232, Ethernet or GPIB (IEEE 488) interfaces
General
purpose and
education
❙Fast boot time
❙Low-noise, intelligent temperature management
❙ Extended display size through Virtual Screen technology
❙ DVI-D output for external display

More information | www.hameg.com 5
Precise Signal Analysis
An excellent sampling rate in combination with a large memory depth is the key
for precise signal analysis. The highly resolved measurement data and the
powerful zoom function expose even minor signal details.
Depending on their requirements users can choose between three 2-channel-
versions and three 4-channel-versions with bandwidths between 300 and
500 MHz.
500 MHz 400 MHz 300 MHz
4 channel HMO3054 HMO3044 HMO3034
2 channel HMO3052 HMO3042 HMO3032
4 HAMEG INSTRUMENTS | HMO3000 SERIES
Bandwidth Upgrade
Should your requirements change, then so does the HMO3000, as the 300
and 400 MHz models can be extended to 500 MHz bandwidth via software
upgrades whenever required.
❙For 300MHz models with options
HOO352 (2 channel) and HOO354 (4 channel).
❙For 400MHz models with options
HOO452 (2 channel) and HOO454 (4 channel).
Options
HOO352 / HOO354 HOO452 / HOO454
Key facts
Sampling rate (per analog channel) 2 GSa/s
Maximum sampling rate 4 GSa/s
Memory depth per channel 4 MPts.
Maximum memory 8 MPts.
Maximum number of logic channels 16
Input impedance 1 MΩ / 50 Ω
V/div. @1 MΩ 1 mV/div. to 5 V/div.
V/div. @50 Ω 1 mV/div. to 1 V/div.
Upgrade at any time
HMO3000 Series
500 MHz
300 MHz | 400 MHz
300 MHz
>>>
500 MHz
400 MHz
>>>
500 MHz

More information | www.hameg.com 76 HAMEG INSTRUMENTS | HMO3000 SERIES
Always a MSO Optional: Logic probe HO3508
❙Logic probe HO3508 fi ts to all
HMO series oscilloscopes
(also available as double pack HO3516)
❙ No hardware lock to a speci c device
❙8 logic channels available
on each logic probe
❙Signal threshold adjustable
for each logic pod
Specifi cations HO3508
Channels 8
Input impedance 100 kΩ || <4 pF
Max. input frequency 350 MHz
Max. input voltage 40 V (DC + peak AC)
Measuring category CAT I
Cable length approx. 1 m
HAMEG is offering the new HMO3000 series exclusively as a mixed-signal oscilloscope. The great
advantages of these instruments are best illustrated by taking a look at how ADCs (Analog Digital
Converter) or DACs (Digital Analog Converter) are integrated. These transformer modules include
an analog signal on the one side and a digital signal on the other side. As with HAMEG's new
HMO3000 series, MSOs allow developers the assessment of the time component for both signal
types on one monitor. As shown in the image below the latency time of a DAC can be determined
with one simple cursor measurement. Therefore a MSO allows developers to devote their full
attention to the circuit without having to waste energy on the measurement setup.
HAMEG is focusing resolutely on the increasing signi cance of the mixed-signal oscilloscopes.
Consequently, all HAMEG HMO oscilloscopes are full-scale MSOs, even the smaller models with a
bandwidth as low as 70MHz. As a result, HAMEG customers will not need to speculate if they
should purchase an instrument with or without logic connectors. As the MSO functionality is
invariably included, all instruments correspondingly offer a secure future. It is also unnecessary to
initially activate the mixed-signal functions via software options, as is the case with other suppliers.
The mixed signal functionality is always included in the HMO3000
series with no software option being necessary to unlock it.
14 bit DAC signal change
HAMEG logic probes
are not linked to a speci c
instrument serial number.
This allows their use with all
digital HAMEG oscilloscopes
in the HMO series.
Mixed Signal
Mixed Signal

More information | www.hameg.com 98 HAMEG INSTRUMENTS | HMO3000 SERIES
Frequency Analysis
FFT functionality
FFT functionality
Due to the outstanding FFT functionality of the HMO series oscilloscopes signals can also be analysed in
the frequency domain with up to 65,536 points. Additional practical tools such as cursor measurement as
well as peak-detect-functions are also available. They allow engineers to complete their analysis signicantly
faster, also in the frequency domain.
Figure 5
Easy analysis in frequency domain
Quite often the distortion of input signals cannot be
detected with the naked eye. For instance, the sine
wave signal displayed in gure 1 appears to be
undistorted. Only the frequency spectrum (gure 2)
- available with just one touch of a button - clearly
displays additional harmonics that occur as
harmonic oscillations for multiples of the basic
frequency.
For non-periodic input signals most instruments
offer the option to trigger the spectrum at just the
right moment to then check it in “STOP” mode
at a later time. However, at that point, many
oscilloscopes with FFT functionality calculate the
spectrum only once and store the result in the
memory. The base time signal will no longer be used
for the calculation. Consequently, an investigation
of all parts of the signal will no longer be possible.
HMO series oscilloscopes work differently: Since
FFT is also active for previously stored signals, it is
possible to subsequently analyze any sections of
those signals captured in single shot mode or stop
mode with an adjustable window width. Figure 3
shows a sine burst signal in the time domain.
Pushing the FFT button will switch the oscilloscope
into the frequency domain. Users can choose
between various measurement windows like the
„rectangular“ type that has been used in gure 4.
Although this window type captures frequencies at
a high degree of accuracy, it is also accompanied
by more noise. In order to suppress this disturbing
interference users can for instance choose the
Hanning window. The impact on the spectrum is
visible in gure 5 (see device screen).
Figure 1: A sinusoid signal that at rst sight appears undistorted Figure 2: The frequency spectrum exposes the signal distortion Figure 3 Figure 4

More information | www.hameg.com 1110 HAMEG INSTRUMENTS | HMO3000 SERIES
Serial Bus Analysis
I2C, SPI, CAN or LIN – in terms of interaction with the outside world for
embedded systems, it is safe to say that these are the most commonly used
communication protocols. The new HMO3000 series by HAMEG Instruments
offers you hardware-accelerated signal triggering and decoding for all of these
protocols. You can upgrade your instrument via software licence keys with those
functions required to develop your application:
❙HOO10: Analysis of I2C, SPI and UART/RS-232 signals on analog and logic
channels
❙HOO11: Analysis of I2C, SPI and UART/RS-232 signals on all analog channels
❙HOO12: Analysis of CAN and LIN signals on analog and logic channels
Serial bus trigger types:
❙I2C: Start, Stop, ACK, nACK,
Address/Data
❙SPI: Start, End, Serial Pattern
(32Bit)
❙UART/RS-232: Startbit,
Frame Start, Symbol, Pattern
❙LIN: Frame Start, Wake Up,
Identier, Data, Error
❙CAN: Frame Start, Frame
End, Identier, Data, Error
SPI bus trigger setup CAN bus conguration
I2C bus hex decoding on the analog
channel
I2C bus ASCII und binary
CAN bus list display
HEX decoded CAN bus signal
HOO10 / HOO11
SPI / I2C / UART/RS-232 bus
analysis for all oscilloscopes
of the HMO series
HOO12
CAN / LIN bus analysis
for all oscilloscopes of the
HMO series
Application
HMO3004 series 4 channel mixed signal oscilloscope
HMO3002 series 2 channel mixed signal oscilloscope
HMO3032 [HMO3034] 300MHz
HMO3042 [HMO3044] 400MHz
HMO3052 [HMO3054] 500MHz
Firmware: ≥ 5.0
Display
Display: 16.5cm (6.5") VGA Color TFT
Resolution: 640 x 480 Pixel
Backlight: LED 500 cd / m2
Display area for traces: 50 Pts / div.
without menu 400 x 600 Pixel (8 x 12 div.)
with menu 400 x 500 Pixel (8 x 10 div.)
Color depth: 256 colors
Intensity steps per channel: 0 to 31
Channel display: False color, inverse brightness
Bus display: up to 2 busses, parallel busses, serial busses
(option), decoding of the bus values in ASCII,
binary, decimal or hexadecimal format; Table
view of the decoded data
Virtual Screen 20 div. vertical for all Math-, Logic-, Bus- and
Reference Signals
LED brightness: 2 steps
Vertical System
Channels:
DSO mode CH 1, CH 2 [CH 1 to CH 4]
MSO mode CH 1, CH 2, LCH 0 to 15 (logic channels)
with 2 x Option HO3508
Auxiliary input: Front side [Rear side]
Function External Trigger
Impedance 1 MΩ || 14 pF ±2 pF
Coupling DC, AC
Max. input voltage 100 V (DC + peak AC)
XYZ-mode: All analog channels on individual choice
Invert: CH 1, CH 2 [CH 1 to CH 4]
Y-bandwidth (-3 dB): 300/400/500 MHz (5 mV to 5 V) /div.
300 MHz: 180MHz (1mV, 2mV)/div.
400 / 500 MHz: 200 MHz (1mV, 2 mV)/div.
Lower AC bandwidth: 2 Hz
Bandwidth limiter (switchable): approx. 20 MHz
Rise time (calculated): 300 MHz: < 1.166 ns
400 MHz: < 0.875 ns
500 MHz: < 0.7 ns
DC gain accuracy: 2% of full scale
Input sensitivity: 12 calibrated steps
CH 1, CH 2 [CH 1 to CH 4] 1mV/div. to 5V/div. (1–2–5 Stepping)
Variable Between calibrated steps
Inputs CH1, CH2 [CH 1 to CH4]:
Impedance 1 MΩ II 13 pF ±2 pF (50 Ω switchable)
Coupling DC, AC, GND
Max. input voltage 1 MΩ: 200 Vp, derates at 20 dB/Decade to
5 Vrms above 100 kHz
50 Ω: < 5 Vrms, max. 30 Vp
Measuring circuits: Measuring Category 0
Position range: ± 8 divs
Offset control:
1 mV, 2 mV ± 0.2 V - 8 div. * sensitivity
5 mV to 20 mV ± 1 V - 8 div. * sensitivity
50 mV ± 2.5 V - 8 div. * sensitivity
100mV, 200mV ±20V - 8div. * sensitivity
500 mV to 5 V ± 50 V - 8 div. * sensitivity
Logic channels: With Option HO3508 / HO3516
Select. switching thresholds TTL, CMOS, ECL, 2 x User -2 V to +8 V
Impedance 100 kΩ || < 4 pF
Coupling DC
Max. input voltage 40 V (DC + peak AC)
Triggering
Trigger modes:
Auto Triggers automatically even when no trigger
event occurs for a certain time
Norm Always triggers when a trigger event occurs
Single Triggers once on a trigger event
Trigger display: LED
Trigger sensitivity:
Intern ≥5 mV / div.: 0.8 div.
≥2 mV / div. to <5 mV / div.: 1div.
<2 mV / div.: 1.5 div.
Ext. trigger via Auxiliary Input [Aux. Input rear side]
Ext. Sensitivity 0.5 V to 10 Vpp
Trigger level range:
With auto level Adjustability of the level between the peak
values of the signal
Without auto level -8div. to +8 div.
External -5 V to +5 V
Trigger types:
Slope:
Slope direction Rising, falling, both
Sources CH 1, CH 2, Line, Ext [CH 1 to CH 4, Line, Ext.]
Coupling
Auto level Adjustability of the level between the peak
values of the signal, 5 Hz to 300/400/400MHz
AC 5 Hz to 300/400/400 MHz
DC 0 to 300/400/400 MHz
HF 30 kHz to 300/400/400 MHz
LF 0 kHz to 5 kHz, selectable for DC, Auto level
Noise rejection (low-pass) 100 MHz, selectable for DC, AC, Auto level
Pulse width:
Polarity Positive, negative
Functions ti>t, ti<t, ti=t, ti/=t, t1<ti<t2, not (t1<ti<t2)
Pulse duration 16ns to 8.589 s, resolution 4 ns/1 µs
Video Pos./neg. sync. impulse
Standards PAL, SECAM, NTSC, PAL-M, SDTV 576i,
HDTV 720p, HDTV 1080i, HDTV 1080p
Fields Upper, lower, both
Line All, line number selectable
Source CH 1, CH 2, Ext. [CH 1 to CH 4]
Logic:
Logic functions AND, OR, TRUE, FALSE, with or without eval-
uation of the duration of the logic operation
Duration functions ti>t, ti<t, ti=t, ti/=t, t1<ti<t2, not (t1<ti<t2),
Timeout
Duration 4 ns to 1 s
Source LC0 to 15
State LC0 to 15 X, H, L
Serial Busses: (Options)
I2CStart, Stop, ACK, NACK, Address/Data
SPI Start, End, Serial Pattern (32Bit)
UART/RS-232 Startbit, Frame Start, Symbol, Pattern
LIN Frame Start, Wake Up, Identifier, Data, Error
CAN Frame Start, Frame End, Identifier, Data, Error
Trigger Holdoff: 50ns to >10 s
2nd Trigger (B):
Type Slope trigger
Slope direction Rising or falling
Min. signal height 0.8 div.
Source CH 1, CH 2, Ext. [CH 1 to CH 4]
Coupling (source B/=A): DC, HF, NR
Coupling (source B=A): see trigger A
Level (source B/=A): -8div to +8div. (adjustable separately by A)
Level (source B=A): see level A
Frequency range 0 MHz to 300 / 400 / 500 MHz
Operating modes:
Time based 16 ns to 8.589 s, resolution 4ns/1 µs
Event based 1 to 216
Horizontal System
Domain representation: Time, Frequency (FFT), Voltage (XY)
Representation Time Base: Main-window, main- and zoom-window
Memory Zoom: Up to 200,000:1
Time Base:
Accuracy 15 ppm
Technical Data

Technical Data
Recommended accessories:
HOO10 Analysis of I2C, SPI and UART/RS-232 signals on analog
and logic channels
HOO11 Analysis of I2C, SPI and UART/RS-232 signals on all analog
channels
HOO12 Analysis of CAN and LIN signals on analog and logic channels
for two buses
HO3508 Active 8 channel logic probe
HO3516 2 x HO3508, active 8 channel logic probes
HO720 USB-device/RS-232 dual-interface card
HO740 IEEE-488 (GPIB) interface card, galvanically isolated
HZ46 4RU 19" Rackmount kit
HZ99 Carrying case for protection and transport
HZ100 Differential probe 20:1/200:1
HZ115 Differential probe 100:1/1,000:1
HZ355 500 MHz passive probe 10:1 with automatic identification
HZ355DU Upgrade from 2 x HZ350 to 2 x HZ355
HZO20 High voltage probe 1000:1 (400MHz, 1000Vrms)
HZO30 1 GHz active probe (0.9 pF, 1 MΩ, including many accessories)
HZO40 Active differential probe 200 MHz (10:1, 3,5pF, 1 MΩ)
HZO41 Active differential probe 800 MHz (10:1, 1pF, 200 kΩ)
HZO50 AC/DC current probe 30 A, DC to 100 kHz
HZO51 AC/DC current probe 100/1000 A, DC to 20 kHz
Accessories included:
HO730 Ethernet/USB dual-interface card, Line cord, printed operating
manual, 2/4 probes (amount=number of channels), 10:1 with attenuation ID
(HZ350 400/300 MHz, HZ355 500 MHz), software-CD
HO730
Built-in Ethernet/USB
dual-interface card
Printed operating manual
and software-CD
HZ350
400 MHz passive probe
(for 400/300 MHz oscilloscopes)
HZ355
500 MHz passive probe
(for 500 MHz oscilloscopes)
More information | www.hameg.com 1312 HAMEG INSTRUMENTS | HMO3000 SERIES
Accessories included:
HO730 Ethernet/USB dual-interface card, Line cord, printed operating
manual, 2/4 probes (amount=number of channels), 10:1 with attenuation ID
(HZ350 400/300 MHz, HZ355 500 MHz), software-CD
HO730
Built-in Ethernet/USB
dual-interface card
Printed operating manual
and software-CD
Recommended accessories:
HOO10 Analysis of I2C, SPI and UART/RS-232 signals on analog
and logic channels
HOO11 Analysis of I2C, SPI and UART/RS-232 signals on all analog
channels
HOO12 Analysis of CAN and LIN signals on analog and logic channels
for two buses
HO3508 Active 8 channel logic probe
HO3516 2 x HO3508, active 8 channel logic probes
HO720 USB-device/RS-232 dual-interface card
HO740 IEEE-488 (GPIB) interface card, galvanically isolated
HZ46 4RU 19" Rackmount kit
HZ99 Carrying case for protection and transport
HZ100 Differential probe 20:1/200:1
HZ115 Differential probe 100:1/1,000:1
HZ355 500 MHz passive probe 10:1 with automatic identification
HZ355DU Upgrade from 2 x HZ350 to 2 x HZ355
HZO20 High voltage probe 1000:1 (400MHz, 1000Vrms)
HZO30 1 GHz active probe (0.9 pF, 1 MΩ, including many accessories)
HZO40 Active differential probe 200 MHz (10:1, 3,5pF, 1 MΩ)
HZO41 Active differential probe 800 MHz (10:1, 1pF, 200 kΩ)
HZO50 AC/DC current probe 30 A, DC to 100 kHz
HZO51 AC/DC current probe 100/1,000 A, DC to 20 kHz
HZ350
400 MHz passive probe
(for 400/300 MHz oscilloscopes)
HZ355
500 MHz passive probe
(for 500 MHz oscilloscopes)
Aging ±5 ppm/year
Refresh operating modes 1 ns/div. to 20 ms/div.
Roll operating modes 50 ms/div. to 50 s/div.
Deskew: -62,5 ns to +61,5 ns
Step size 500 ps
Search functions: Slope, Pulse, Peak, Rise-/Falltime, Runt
Marker: up to 8 user definable marker for easy naviga-
tion; automatic marker function based on
search criteria
Digital Storage
Sampling rate: 2 x 2 GSa/s, 1 x 4 GSa/s
[4 x 2 GSa/s, 2 x 4 GSa/s]
Logic channels: 16 x 1 GSa/s
Resolution (vertical): 8 Bit, HiRes 10 Bit
Memory: 2 x 4 MPts [4 x 4 MPts], 1x 8 MPts [2 x 8 MPts]
Operation modes: Refresh, Average (1024), Envelope, Peak-
Detect (500ps), Filter, Rol (free run/triggered
from time base 50 ms/div. and slower),
HiRes
Interpolation: CH 1 to CH 4: Sinx/x, Pulse, Linear;
LC0 to 15: Pulse
Persistence: Off, 50 ms to ∞
Delay pretrigger: 0 to 4 Million x (1/samplerate), Interlaced x2
posttrigger 0 to 8,59 Billion x (1/samplerate)
Display refresh rate: Up to 4,800 waveforms/s
Display: Dots, vectors (interpolation), ‘persistence’
Operation/Measuring/Interfaces
Operation: Menu-driven (multilingual), Autoset,
help functions (multilingual)
Frequency counter:
0.5 Hz to 300/400/500 MHz 6 Digit resolution
Accuracy 15 ppm
Aging ±5 ppm/year
Auto measurements: Vpp, Vp+, Vp-, Vrms, Vavg, Vtop, Vbase, amplitude,
phase, frequency, period, risetime 80/ 90%,
falltime 80 /90 %, pos./neg. pulse width, pos./
neg. duty cycle, standard deviation, delay,
pos./neg. edge count, pos./neg. pulse count,
trigger period, trigger frequency
Statistic Min., max., mean, standard deviation,
number of measurements for up to
6 Functions simultaneously
Cursor measurements: ∆V, ∆t, 1/∆t (f), V to GND, Vt related to Trigger
point, ratio X and Y, pulse count, edge count,
peak to peak, peak+, peak-, mean value,
RMS value, standard deviation, rise time,
duty cycle
Application memory: 8 MByte for references, device settings and
formulars
Interface:
Internal 2x USB-Host (type A) (1x front side, 1x rear
side), mass storage (FAT16/32)
Exchangeable HO730 Dual-Interface Ethernet/USB-Device
(type B)
Video OUT: DVI-D (480 p, 60 Hz) for external display,
HDMI compatible
Trigger OUT: BNC (rear side), Modes: Trigger, Mask
Optional: USB-Device/RS-232 Dual-Interface (HO720),
IEEE-488 (GPIB) (HO740)
Mathematic functions
Quickmath: ADD, SUB, MUL, DIV
Editor for formula sets: Max. 5 formulas per formula set
Label for: Math. memories and formula set
Sources: All channels and math. Memories,
constants
Targets: Math. memories
Functions: ADD, SUB, 1/X, ABS, MUL, DIV, SQ, POS,
NEG, INV, SQR, MIN, MAX, LOG10, LN,
Integral, Differential, High-pass filter,
Low-pass filter
Display: Up to 4 math. memories with label
Mask test: Signal test (pass/fail) based on previously
defined mask
Quickview: Display of Vp+, Vp-, RMS value, rise time,
fall time
General Information
Probe ADJ Output: 1 kHz/1MHz square wave signal
approx. 0,2Vpp (ta <4 ns)
Bus Signal Source (4Bit): SPI, I2C, UART, retangle, 4Bit counter,
4 Bit random pattern
Internal RTC (Realtime clock): Date and time for stored data
Line voltage: 100 V to 240V, AC 50 Hz to 60Hz, CAT II
Power consumption: Max. 70 [90] W
Protective system: Safety class I (EN61010-1), CSA (pending)
Operating temperature: +5 °C to +40 °C
Storage temperature: -20 °C to +70 °C
Rel. humidity: 5 % to 80% (non condensing)
Theft protection: Kensington Lock
Dimensions (W x H x D): 285 x 175 x 220 mm
Weight: 3.6kg
All data valid at 23°C after 30 minute warm-up.
Recommended Accessories
HO720
USB-device/RS-232 dual-
interface card
HZ99
Carrying case for
protection and transport
HZO20
High voltage probe 1000:1
(400 MHz, 100 0 Vrms)
HZO30
1 GHz active probe
(0.9 pF, 1 MΩ, including many accessories)
HZO40
Active differential probe
200 MHz (10:1, 3.5 pF, 1 MΩ)
HZO41
Active differential probe
800 MHz (10:1, 1 pF, 200 kΩ)
HZO50
AC/DC current probe 30 A,
DC to 100 kHz
HZO51
AC/DC current probe
100/1000 A, DC to 20 kHz
HZ115
Active differential
high voltage probe
HZ355
500 MHz passive probe 10:1
with automatic identication
HZ355DU
Upgrade from
2 x HZ350 to 2 x HZ355,
only available when
purchasing a HMO3000
(300 MHz / 400 MHz
models)
HO740
IEEE-488 (GPIB) interface
card, galvanically isolated
HZ46
4 RU 19” rackmount kit
Accessories

HMO compact series
Bandwidth 200 MHz 150 MHz 100 MHz 70 MHz
Model: 4 channel
2 channel
HMO2024
HMO2022
HMO1524
HMO1522
HMO1024
HMO1022
HMO724
HMO722
Sampling rate (per analog channel) 1 GSa/s
Maximum sampling rate 2 GSa/s
Memory depth per channel 1MPts.
Maximum memory 2 MPts.
Max number of logic channels 8
Input impedance 1 MΩ / 50 Ω 1 MΩ
V/div. @ 1 MΩ 1 mV/div. to 10 V/div.
V/div. @ 50 Ω 1 mV/div. to 1 V/div. n/a
DC-offset ± 0.2V to ± 100V –
Component tester ■
14 HAMEG INSTRUMENTS | HMO3000 SERIES
HMO Compact Series
8 different models in a compact design with bandwidths from 70 to 200 MHz
available with 2 or 4 channels. The mixed signal functionality is always included
in the HMO compact series with no software option being necessary to unlock it.
Key facts
❙ 2 GSa/s real time, low noise fl ash A/D converter
❙2 MPts memory, zoom up to 50,000:1
❙MSO functionality included as standard
(HO3508 logic probe with 8 channels required)
❙Component tester for capacitors, inductors and semiconductors
❙Vertical sensitivity up to 1mV/div.
❙Trigger modes: slope (A/B), pulse width, video, logic, serial buses (optional)
❙Serial bus trigger and hardware accelerated decode incl. list view.
Options: I2C + SPI + UART/RS-232 (HOO10/HOO11), CAN + LIN (HOO12)
❙28 auto-measurement parameters plus statistics, formula editor, ratio cursor
❙6-digit hardware counter
❙FFT up to 64 kPts (dBm, dBV, Vrms)
❙Pass/fail test based on masks
❙ Automatic search for user-de ned events
❙ Display: 12 div. x-axis, 20 div. y-axis (Virtual Screen)
❙ 2x USB for mass storage, RS-232/USB dual interface for remote control
200 MHz | 150 MHz | 100 MHz | 70 MHz
HMO compact series
Small foot print Bus signal sourceBuilt-in component tester
From entry level to
high performance.
Oscilloscopes from
the T&M expert.
Fast operation, easy to use, precise measurements –
that’s Rohde & Schwarz oscilloscopes.
R&S®RTO: high performance (Bandwidths: 600MHz to 4GHz)
R&S®RTM: upper midrange (Bandwidths: 350MHz and 500MHz)
HMO3000: midrange (Bandwidths: 300MHz to 500 MHz)
HMO Compact: value range (Bandwidths: 70MHz to 200MHz)
All Rohde & Schwarz oscilloscopes incorporate time domain,
logic, protocol and frequency analysis in a single device.
Take the dive at www.scope-of-the-art.com

value-instruments.com
HAMEG Instruments GmbH
Industriestr. 6 | 63533 Mainhausen | Germany | Phone [phone]
www.hameg.com
R&S® is a registered trademark of Rohde & Schwarz GmbH &Co. KG
HAMEG Instruments® is a registered trademark of HAMEG
Instruments GmbH | Trade names are trademarks of the owners
11 / 2013 | © HAMEG Instruments GmbH | 4A-D000-0430
Printed in Germany | Subject to change without notice