Havis C-DMM-3005 User manual

C‐DMM‐3005_INST_8‐18


INSTALLATIONINSTRUCTIONS
C‐DMM‐3005FlipupDashMonitorMount
2018‐2019DodgeCharger(PolicePursuitPackage)
**DoesNOTworkinvehiclewith12.1inchIntegratedTouchScreenDisplay**
TOOLSREQUIRED:
RatchetWrench Dashpanelremovaltool OpenEndWrench‐7/16”
SocketSet   Phillipsscrewdriver
Always!
ReadallinstructionsbeforeinstallinganyHavis,Inc.products.
Checkforobstructions(Wires,brakelines,fueltank,etc.)beforedrillinganyholes!
Usehardwareprovidedwithinstallkit
HARDWAREandPARTS:
QTY DESCRIPTIONPART#
1DriversidesupportbracketCM009445
1Passengersidesupportbracket  CM009444
2SidemountingbracketCM009446
410‐32x3/8"MachinescrewGSM33117
4#10StarwasherGSM31034
410‐32NylocknutGSM30015
4#10FlatwasherGSM31003
1VESArotatorplateCM009068
1PVCwasherCM008582
21/4"PlasticwasherCM86600
21/4"SteelwasherGSM31005
21/4"NylocknutGSM30016


Notes:
TheC‐DMM‐3000swivelplateacceptsC‐MM‐301offsetbracketusedwithC‐MM‐2XXadaptors.
C‐MM‐2XXseriesadaptorbracketsarenotneededformostVESA75andotherHavisDockingStation
mountingapplications.
CM009068VESArotatorplategivesadditionalpositioningoptions,butisnotrequireddependingon
mountingpreference.

C‐DMM‐3005_INST_8‐18


C‐DMM‐3005
Assembly
CM009068
VESA75rotatorplate
CM008582
PVCspacer
GSM31005
–
Flatwasher
CM86600–Nylonflatwasher
GSM30016–Nylocknut
CM009446
Sidemountingbracket
CM009445
Driverside
supportbracket
CM009444
Passengerside
su
pp
ortbracket
GSM31003
–
Flatwasher
GSM30015–Nylocknutwasher
GSM33117‐10‐32x3/8Machinescrew
GSM31003‐#10flatwasher
Forattachingsidemountingbracketsto
mainframe(notshown)

C‐DMM‐3005_INST_8‐18


DodgeChargerDash
Priortoinstallation.
Repeatprocessforbothsides.
Makesurebracketsfitaroundradiosnug.
Temporarilyremovetwo(2)OEMscrewsand
attachsupportbracketwithOEMscrewasshown.
10mmsocket.
Gentlypryalongthedashwithaflatbladepanel
removaltool.Slowlyworkingalongtheframe.
Temporarilyremoveradiotouchscreen.
NOTE:Thetouchscreenhasatheftdeterrentsystembuilt
insowesuggestleavingthemainpowerpluggedin.
Phillipsscrewdriver.
Dashpanelpartiallyremoved.


C‐DMM‐3005_INST_8‐18




Reinstalltheradiotouchscreenusingthe
previouslyremovedOEMhardware.
AttachmainC‐DMM‐3005frametothesidesupport
bracketsusing10‐32x3/8”screwsandstarwashers.
Makesurethesidemountingbracketsare
evenalongthedashandthedashisfully
seatedbackintoplace.
Attachsidemountingbracketstothesidesupport
bracketsusing10‐32nylocknutsandflatwashers.
Carefullyreinstallpreviouslyremoveddashpanel.Repeatprocessfordriversideandtightenhardware.

C‐DMM‐3005_INST_8‐18



AttachVESArotatorplatetothemountingbracket
ofthedeviceyouareattaching.
Installationisnowcomplete.
Doublecheckallhardware,latchingandwire
harnessclearance.
AttachtherotatorplatetotheswivelusinglargePVC
washer,1/4nylonwashers,metalwashers,andnylock
nuts andsto
p
nuts.
Attachthedocktothemountingbracket (with
hardwaresuppliedwithdock).Runwiresasdesired.
ConfirmsmoothoperationoftheC‐DMM‐3005.