HIK VISION DS-PD1-EB-WS2 User manual

DS-PD1-EB-WS2
Wireless Panic Buon
LEDs : General LEDs
(i) From power up: Not learnt
Appearance Descripon
Register Panic Buon Locally
Register Panic Buon Locally via APP
(ii) Learning process
(iii) 8 x Flashes: Learnt
(iv) 18 x Slow flashes: Fault with new baery installed
(v) Signal strength sent to control panel
(vi) Hold up alarm has been acvated
(vii) Control panel has not received the signal from HUD
Diagram References:
ENGLI S H
Specificaon
Baery Informaon

The baery supplied has been chosen to provide long service life
whilst, for safety reasons, having limited output current.
When disposing of the product, the baery must be removed and
disposed of separately inaccordance with the local regulaons.
.
(iv) 18 x Slow flashes:
Fault with new baery
installed
(iii) 8 x flashes: Learnt
(i) From power up:
Not learnt
(ii) Learning process
(vii) Control panel has
not received the
signal from HUD
(vi) Panic alarm has
been triggered
A
A
B
CLEDs - General LEDs
DB
C
D
C
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the RE Direcve 2014/53/EU,
the EMC Direcve 2014/30/EU, the LVD Direcve
2014/35/EU, the RoHS Direcve 2011/65/EU.
Learn Panic Button via APP
1Log in to the APP Store and input “Hik-Connect”
to search the mobile client.
5
6
Log in the Hik-Connect and ap the icon “+” at
the upper-right coner of the Hik-Connect page to
add the security control panel. You can scan the
QR code on the device rear panel or on the
package box, or input the device serial No.
manually to add the device when the device is in
the registraon mode.
Aer adding the security control panel, tap the
arming status icon on the right of the security
control panel’s name to enter the Paron page.
Learn Panic Button onto Control Panel
Appearance
With in 50cm
Panic Buon
Indicator
Panic Buon
2Download and install Hik-Connect to your phone.
3Aer installing, tap to run the client.
4Power on the security control panel.
7Tap the “+” icon on the Paron page to add the
peripherals.
Register Detector
Control Panel
1. Make the security control panel enter the registraon mode.
2. Register the panic buon: Hold any one of the buons unl the
two LEDs flash alternately. The green LED will flash 8 mes if the
registraon is finished.
3. Communicaon Test: press the buon to trigger the alarm .
Note: The distance between the security control panel and the
detector should be less than 50 cm.
Unregister Detector
Inialize the Detector
1. Remove the baery to power the panic buon off.
2. Hold any of the buons and reinstall the baery to power the
detector on at the same me. Release the buon while the two
LEDs flash once together. When the inializaon is completed, the
indicator turns to alternately flashing red and green.
Please register the device winthin 90 seconds after it being powered on.
Hold-upfunconYes
LED indicaonRed, Amber,Green
Operang temperature -10°C to +40°C
Dimensions (H x W x D) 72 x 30 x 20mm
Transmission frequency
Range in open space 300m
Baerytype CR1/3N
Baeryvoltage 3V
Threshold2.1V+/- 5%
Electrical conformity CE
Warranty 2 years
Seng devices technical characteriscs
Environmental and operang features
Electrical & baery
Cerficaons and warranty
433.6MHZ

Product Informaon
User Manual
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co.,
Ltd.
ALL RIGHTS RESERVED.
Any and all informaon, including, among others, wordings,
pictures, graphs are the properes of Hangzhou Hikvision
Digital Technology Co., Ltd. or its subsidiaries (hereinaer
referred to be “Hikvision”). This user manual (hereinaer
referred to be “the Manual”) cannot be reproduced, changed,
translated, or distributed, parally or wholly, by any means,
without the prior wrien permission of Hikvision. Unless
otherwise spulated, Hikvision does not make any warranes,
guarantees or representaons, express or implied, regarding to
the Manual.
About this Manual
This manual is applicable to Panic Buton.
The Manual includes instrucons for using and managing the
product. Pictures, charts, images and all other informaon
hereinaer are for descripon and explanaon only. The
informaon contained in the Manual is subject to change,
without noce, due to firmware updates or other reasons.
Please find the latest version in the company website
(hp://overseas.hikvision.com/en/).
Please use this user manual under the guidance of
professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the
properes of Hikvision in various jurisdicons. Other
trademarks and logos menoned below are the properes of
their respecve owners.
FCC Informaon
FCC Informaon
Please take aenon that changes or modificaon not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protecon against harmful interference in a
residenal installaon. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instrucons, may cause harmful interference
to radio communicaons. However, there is no guarantee that
interference will not occur in a parcular installaon. If this
equipment does cause harmful interference to radio or television
recepon, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
FCC Condions
This device complies with part 15 of the FCC Rules. Operaon is
subject to the following two condions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operaon