Htek UC842 User manual

Hardware Overview
LEDs
1. Power Indicator: Steady green when power on, blinking green when the call is ringing.
2. Line Keys
Steady green: during the conversation, or plan to dial a call.
Blinking red: the call is ringing.
Off: idle interface
Place a call
Three ways to make a call:
1) Handset: Pick up the handset; enter the number, and then press the send soft key or
press .
2) Speaker: Press or the line keys; enter the number, and then press the send soft key
or press .
3) Headset: Press ; enter the number, and then press the send soft key or press .
Note: You can also use Contacts or call log to dial the number you want, press place the
call by the three ways mentioned. More, you can also alternate the mode during the
call.
End a call
To end a call in three different modes:
1) Handset: hang up the handset or press the cancel soft key.
2) Speaker: press , or press the cancel soft key
3) Headset: press the cancel soft key.
Answer a call
1) Handset: pick up the handset;
2) Speaker: press ;
3) Headset: press .
Note: You can also reject the call by press the Reject soft key.
Redial
Press to redial the last call that dialed.
Hold
Press or press the hold soft key during a call to hold the call,
Press or resume soft key to resume the call.
Call Transfer
Blind Transfer
a. Press or transfer soft key during the conversation, the call is on hold now.
b. Enter the number that transfers to.
c. Press or the transfer soft key, and now the blind transfer completed.
Attended Transfer (at least one line key set as Auto)
a. Press or transfer soft key during the conversation, the call is on hold now.
b. Enter the number that transfer to, and press the send soft key or .
c. Start the second conversation, press or transfer soft key, then, transfer completed.
Semi-Attended Transfer (at least one line key set as Auto)
a. Press or transfer soft key during the conversation, the call is on hold now.
b. Enter the number transfer to, and then press , then you can hear the ring tone.
c. Press or the Tran soft key, and now the Semi-attended transfer completed.
Call Conference
Assuming that A and B are in conversation. A wants to bring C (or D & E) in a conference:
1) A press line 2, the call is placed on hold.
2) A enter the number of C and then press send soft key or . C answers the call.
3) A press or the conference soft key, then A, B and C are now in a conference.
4) If add D&E, press Line 3, the current conference is on hold, dial D and press , the four
are in conference. Press line 4, and dial E, press , then A,B,C,D,E are in conference.
Note: 1) If C does not answer the call, A can back to continue the conversation with B;
2) Once A hangs up the call, the conference is ended, while if B or C drops the call, A&C
or A&B conversation continues.
Call Mute
Press to mute the microphone during the call
Press again to un-mute the conversation.

Instrucon
Configuraon
1. Configuraon via Phone
a. Press Menu→Seng→Advanced Sengs (Default password: admin)
b. Select Network: To configure the Wan Port (DHCP/Stac/PPPoE), PC Port…
c. Select Accounts: To configure enable the account; fill the SIP SERVER, Outbound Proxy, ID…
d. Save the configuraon
2. Configuraon via Web
a. Get the IP address from the phone: Press Menu→Status.
b. Login: input the IP address in the web browser. The PC and phone should be in the same
segment) /Login name: admin password: admin (default)
c. Configure: select network/Account…to fill the relevant content.
d. Save the configuraon, or if want to reboot, click the reboot buon.
Support Contact
Nanjing Hanlong Technology Co., Ltd.
[e-mail]
Tel: [phone]
Fax: [phone]
www.htek.com
5th Floor, 1st Building
Huashen Tech Park
10 Huashen Temple
Yuhuatai Dis. Nanjing 210012
China
© Nanjing Hanlong Technology Co., Ltd. 2005-2016 All rights reserved.
Quick Reference
For
UC842, UC840P, UC804P, UC804