HunterDouglas RB 500 5-287-216 Series User manual

Installation InstructionS
RB 500 Motorized Roller Shades
4" Fascia Coupled
Series 5-287–216
1
Compatible Motors
LT50 RA 525A2
LT50 Altus RTS 525A2
Sonesse 50 RTS 506S2
Sonesse 50 DCT 506S2
Sonesse 50 RA 506S2
Sonesse 50 RS485 506S2
Sonesse 50 RTS 510S2
Sonesse 50 DCT 510S2
Sonesse 50 RA 510S2
Sonesse 50 RS485 510S2
Sonesse ULTRA 50 RTS 506A2
Sonesse ULTRA 50 RA 506A2
Sonesse ULTRA 50 RS485 506A2
LT50 RS485 515S2
LT50 RS485 535A2
Sonesse ULTRA 50 DC RTS 504A8
Sonesse 50 DC RS485 504A8
Sonesse 30 RTS
Sonesse 30 DCT
Sonesse 30 RS485

Insert the Plate L into the intermediate bracket.
Turn the Plate L in the rolling off direction(1) and
secure with the locking .)2(pilc
Not necessary when using bracket with leveler.
Install the clutch bracket and intermediate bracket
first.
a) recess b) ceiling c) wall
Place the shade with the idle end onto the bracket.
Push the shade against tube bearing plug and lift it up ...
Installation
1
2
2
1
a
c
b
2

Turn the blind (10°) in the rolling off direction (1) and
1
2
Fix the blind by turning the locking ring against the
bearing.
3

To adjust skewing, put the provided Allen key into
the screw of the leveller and turn it left or right to
move the blind up and down. Support lifting of large
heavy blinds with the palm of your hand.
Option: Leveller
4

2
1
click
21
3I
Install the outer bracket with the screws provided.
.
Use a pair of pliers to break off the stopper from the
intermediate bracket.
Slide the aligner or the connector set through the
intermediate bracket into the tube bearing plug.
Press the idle end, lift the roller shade and snap it
into the bracket.
Place the tube adapter on the aligner or connector
head.
Fix the roller shade by turning the locking ring
against the idle end.
Place the front profile in the bracket. Make sure that
the profile slides under the nose of the bracket.
To align the bottom rails, push the shade against
the idle end (1), turn the shade, level the bottom rail
with the other one (2). Release to fix the position (3).
Not possible when using connector set.
To adjust skewing, put the provided Allen key into
the screw of the leveller and turn it left or right to
move the shade up and down. Support lifting of large
heavy roller shades with the palm of your hand.
Option: Leveller
5
Installation: Coupled shade

2
1
click
21
3
Fix the outer bracket with the screws provided.
Install the main roller shade (without the end cap).
Use a pair of pliers to break off the stopper from the
bracket on the idle end side.
Slide the aligner or the connector through the brack-
et into the idle end.
Press the tube bearing plug, lift the roller shade
and snap it into the bracket.
Place the tube with plug connector on the aligner or
connector set head.
Fix the roller shade by turning the locking ring
against the idle end.
Place the front profile in the bracket. Make sure that
the profile slides under the nose of the bracket.
To align the bottom hembars, pull the shade away
from aligner set (1), turn shade to line up bottom
hembars together (2). Release shade to secure
position (3). Not possible when using connector set.
To adjust skewing, put the provided Allen key into
the screw of the leveller and turn it left or right to
move the shade up and down. Support lifting of large
heavy roller shades with the palm of your hand.
Installation
Option: Leveller
6

2
1
click
21
3
Fix the outer bracket with the screws provided.
Install the main roller shade (without the end cap).
Use a pair of pliers to break off the stopper from the
bracket on the idle end side.
Slide the aligner or the connector through the brack-
et into the idle end.
Press the idle end, lift the roller shade and snap it
into the bracket.
Place the tube adapter on the aligner or connector
head.
Secure shade band by turning the locking ring
on tube bearing plug furthest away from the bracket.
Place the fascia in the bracket. Make sure that
the fascia slides under the nose of the bracket.
To align the bottom rails, push the shade against
the idle end (1), turn the shade, level the bottom rail
with the other one (2). Release to fix the position (3).
Not possible when using connector set.
To adjust skewing, put the provided Allen key into
the screw of the leveler and turn it left or right to
move the shade up and down. Support lifting of large
heavy roller shades with the palm of your hand.
Installation
Option: Leveler
7

1
2
click
Place the screw driver under the bracket cover, turn
the screw driver and slide the bracket cover from the
bracket.
Slide the bracket covers onto the brackets.
Press the bottom of the front profile upwards (1)
and pull it outwards (2).
Move the roller shade downwards out of the brack-
et. Pull the aligner or connector out of the idle end.
Unfasten the locking ring. Slide a screw driver
between locking ring and bracket and push the idle
end in the crank direction.
Type 5-237
5-247
5-307
5-327
Push the fascia to snap it into the bracket.
Installation Instruction
Roller Shade (Fascia)
Coupled Shades
Removal
8

1
2
click
Place the screw driver under the end cap, turn
the screw driver and slide the end cap from the
bracket.
Slide the end caps onto the brackets.
Press the bottom of the fascia upwards (1)
and pull it outwards (2).
Move the roller shade downwards out of the brack-
et. Pull the aligner or connector out of the idle end.
Unfasten the locking ring. Slide a screw driver
between locking ring and bracket and push the tube
bearing plug in the aligner/connector direction.
Type 5-237
5-247
5-307
5-327
Push the profile to snap it into the bracket.
Installation Instruction
Roller Shade (Fascia)
Coupled Shades
Removal
9

Connect the motor and all controls in accordance
with all safety standards.
2
10